PubMed Health⌕ Search

Biomedical subjects

A Folch

Publications and source records attributed to A Folch.

6 recordsLinked to original sources
PubMed2000

Microfabricated elastomeric stencils for micropatterning cell cultures.

Here we present an inexpensive method to fabricate microscopic cellular cultures, which does not require any surface modification of the substrate prior to cell seeding. The method utilizes a reusable elastomeric stencil (i.e., a membrane containing thru holes) which seals spontaneously against the surface. The stencil is applied to the cell-culture substrate before seeding. During seeding, the stencil prevents the substrate from being exposed to the cell suspension except on the hole areas. After cells are allowed to attach and the stencil is peeled off, cellular islands with a shape similar to the holes remain on the cell-culture substrate. This solvent-free method can be combined with a wide range of substrates (including biocompatible polymers, homogeneous or nonplanar surfaces, microelectronic chips, and gels), biomolecules, and virtually any adherent cell type.

Animals↗
PubMed2000

Microengineering of cellular interactions.

Tissue function is modulated by an intricate architecture of cells and biomolecules on a micrometer scale. Until now, in vitro cellular interactions were mainly studied by random seeding over homogeneous substrates. Although this strategy has led to important discoveries, it is clearly a nonoptimal analog of the in vivo scenario. With the incorporation--and adaptation--of microfabrication technology into biology, it is now possible to design surfaces that reproduce some of the aspects of that architecture. This article reviews past research on the engineering of cell-substrate, cell-cell, and cell-medium interactions on the micrometer scale.

Animals↗
PubMed1999

Molding of deep polydimethylsiloxane microstructures for microfluidics and biological applications.

Here we demonstrate the microfabrication of deep (> 25 microns) polymeric microstructures created by replica-molding polydimethylsiloxane (PDMS) from microfabricated Si substrates. The use of PDMS structures in microfluidics and biological applications is discussed. We investigated the feasibility of two methods for the microfabrication of the Si molds: deep plasma etch of silicon-on-insulator (SOI) wafers and photolithographic patterning of a spin-coated photoplastic layer. Although the SOI wafers can be patterned at higher resolution, we found that the inexpensive photoplastic yields similar replication fidelity. The latter is mostly limited by the mechanical stability of the replicated PDMS structures. As an example, we demonstrate the selective delivery of different cell suspensions to specific locations of a tissue culture substrate resulting in micropatterns of attached cells.

Biocompatible Materials↗
PubMed1999

Numerical model of fluid flow and oxygen transport in a radial-flow microchannel containing hepatocytes.

The incorporation of monolayers of cultured hepatocytes into an extracorporeal perfusion system has become a promising approach for the development of a temporary bioartificial liver (BAL) support system. In this paper we present a numerical investigation of the oxygen tension, shear stress, and pressure drop in a bioreactor for a BAL composed of plasma-perfused chambers containing monolayers of porcine hepatocytes. The chambers consist of microfabricated parallel disks with center-to-edge radial flow. The oxygen uptake rate (OUR), measured in vitro for porcine hepatocytes, was curve-fitted using Michaelis-Menten kinetics for simulation of the oxygen concentration profile. The effect of different parameters that may influence the oxygen transport inside the chambers, such as the plasma flow rate, the chamber height, the initial oxygen tension in the perfused plasma, the OUR, and K(m) was investigated. We found that both the plasma flow rate and the initial oxygen tension may have an important effect upon oxygen transport. Increasing the flow rate and/or the inlet oxygen tension resulted in improved oxygen transport to cells in the radial-flow microchannels, and allowed significantly greater diameter reactor without oxygen limitation to the hepatocytes. In the range investigated in this paper (10 microns < H < 100 microns), and for a constant plasma flow rate, the chamber height, H, had a negligible effect on the oxygen transport to hepatocytes. On the contrary, it strongly affected the mechanical stress on the cells that is also crucial for the successful design of the BAL reactors. A twofold decrease in chamber height from 50 to 25 microns produced approximately a fivefold increase in maximal shear stress at the inlet of the reactor from 2 to 10 dyn/cm2. Further decrease in chamber height resulted in shear stress values that are physiologically unrealistic. Therefore, the channel height needs to be carefully chosen in a BAL design to avoid deleterious hydrodynamic effects on hepatocytes.

Animals↗
PubMedDate not supplied

Cellular micropatterns on biocompatible materials.

We present a method to produce micropatterns of cells on tissue culture substrates. A network of deep elastomeric microchannels defining the desired pattern is sealed onto the surface of interest, and a protein template is created by injecting sub-milliliter quantities of protein solution into the microchannels. Protein adsorbs only on the areas that were exposed to the microflow. After the channels are flushed and the elastomer is removed, cells attach only on the protein template. Micropatterns of collagen or fibronectin were used to selectively adhere cells on various biomedical polymers and on heterogeneous or microtextured substrates. Since the bare substrate areas remain apt for seeding other, more adhesive cell types such as fibroblasts, we were able to create micropatterned co-cultures. Our method allows for inexpensive patterning of a rich assortment of biomolecules, cells, and surfaces under physiological conditions.

Animals↗