Biomedical subjects

A M Bouwman

Publications and source records attributed to A M Bouwman.

4 recordsLinked to original sources

PubMed2006

The use of Stokes deformation number as a predictive tool for material exchange behaviour of granules in the 'equilibrium phase' in high shear granulation.

The objective of this study was three-fold; to investigate the different mechanisms of material exchange during the equilibrium phase of the granulation process and whether these mechanisms are consistent with the mechanisms described in the growth regime map, to study how material properties and process conditions affect these exchange mechanisms, and to correlate Stokes deformation number to the exchange mechanisms. Microcrystalline cellulose (MCC), alpha-lactose, microfine cellulose (MFC), and dextrin were granulated using water as a binding agent. Once in the equilibrium phase, 5% (w/w) of the granular mass was replaced with wet tracer granules, after which the granulation process was continued. Granules were typically of a size of approximately 1mm in diameter. Therefore, these granules can also be called pellets. Tracer experiments show indeed solid material exchange can take place in the equilibrium phase of the high shear granulation process. Tracer material was equally dispersed throughout the whole batch for all materials tested. However, the granulation time needed to reach this homogeneous distribution varied with material and granulation conditions. Three different mechanisms of material exchange were identified: exchange by disintegration, where granules are rapidly crushed and formed to granules again; exchange by deformation, where abraded granule fragments immediately fuse with other granules; and exchange by distribution, where there is a prolonged period over which both tracer and standard granules stay intact, followed by uncontrolled growth and exchange of material. It was found that it is possible to shift between the mechanisms by changing the process conditions, e.g., changing viscosity or amount of binder liquid. These observations indicate that by choosing the appropriate process conditions improved distribution of small amounts of insoluble materials in the granules can be obtained. A relation exists between the exchange mechanisms and the growth regime map: the disintegration mechanism resembles 'crumb behaviour', the deformation mechanism resembles 'steady growth', and the distribution mechanism resembles 'nucleation' and 'induction growth'. Unfortunately, Stokes deformation number cannot be used as a predictive tool when low viscosity binders like water are used, due to the importance of viscosity in the equation. However, this number is one of the variables of the growth regime map. Since the exchange mechanisms correspond to the granule growth mechanisms in the regime map, alternatively colour experiments might be used to reveal the granulation regime.

Algorithms↗

PubMed2005

The effect of the amount of binder liquid on the granulation mechanisms and structure of microcrystalline cellulose granules prepared by high shear granulation.

The structure of granules changes during the high shear granulation process. The purpose of this research was to investigate the effect of the amount of binder liquid on the structure of the granules and the structural changes which occur during the granulation process, using microcrystalline cellulose (MCC) and water as the model system. The structure is the result of the granulation mechanism; therefore, conclusions can be drawn about the latter by studying the former. X-ray microtomography and scanning electron microscopy (SEM) were applied in order to visualise the densification process of granules, which were first freeze dried in order to preserve their structure. Variations in their porosity were quantified by applying image analysis to the tomography results. In order to link the granule mechanical properties to their structural differences, a micromanipulation technique was used to measure granule resistance to deformation. MCC granules granulated with 100% (w/w) water showed increased densification with time, as expected; detailed examination showed that densification is more pronounced in the core of the granule; whereas the outer part remained more porous. Increased densification reduces deformability, so that granules become more resistant to breakage. The lower deformability of the densified granules in the final stages of granulation might result in establishment of equilibrium between attrition and growth, without substantial gross breakage. On the other hand, when more water was used (125%, w/w), densification was hardly observed; the porosity of the granule core was still high even after prolonged granulation times. This may be explained by the fact that higher water content increases the ease of deformation of granules. This increased deformability led to significant granule breakage even during the final phases of the granulation process. Therefore, for these granules a final equilibrium between breakage and coalescence might be established. This also explains why more granules produced with 125% granulation liquid were composed of fragments of irregular shape. Our results establish the link between the granulation behaviour of MCC in the latter stages and the material structure of these granules, which is determined by their liquid content. The process conditions (amount of liquid) to be chosen depend largely on the final purpose for which the granular material is produced.

Cellulose↗

PubMed2005

The relation between granule size, granule stickiness, and torque in the high-shear granulation process.

PURPOSE: To investigate the background of the observed relationship between measured torque and granule size in high-shear granulation processes. METHODS: Torque was measured during the granulation process; the behavior of individual wet granules during compaction was investigated using micromanipulation. Surface properties of wet granules were manipulated by coating them with talc. RESULTS: The torque-granule size relationship could not be explained by the rise in mass of the individual granules; it occurs rather through an increase in stickiness of the granules when the moisture content is increased. Obviously, the increased stickiness that causes the granules to grow also increases the torque. Increased stickiness was shown to be the result of an increased deformability of the granules at higher moisture contents, in combination with a change in surface properties. The elastic-plastic behavior (ratio of elastic to plastic deformation) was found to change at increasing moisture contents. CONCLUSIONS: Our results imply that changes in the stickiness of the granular material that may be caused by changes in composition shift the torque-size relationship. This may be of particular importance when, for example, granulation results from placebo batches are used to predict the granule size of drug-containing batches.

Particle Size↗

PubMedDate not supplied

Improved efficiency of budesonide nebulization using surface-active agents.

Our aim was to improve the efficiency of nebulised budesonide using surface-active agents. Cationic, anionic, and nonionic detergents were added to commercial budesonide suspension, and the particle size distribution during nebulization was measured using both cascade impaction and laser diffraction. Our results showed that the emitted dose was increased after addition of cationic (p < 0.001) and nonionic detergents (p < 0.01) compared with the commercial formulation alone. The respirable fraction was increased for all detergent formulations (p < 0.001) compared with the commercial formulation. We concluded that cationic and nonionic detergent increased the total output of budesonide from the Sidestream. All detergent formulations increased the respirable fraction of nebulized budesonide.

Administration, Inhalation↗