PubMed Health⌕ Search

Biomedical subjects

Alfons Baiker

Publications and source records attributed to Alfons Baiker.

At least 19 recordsLinked to original sources
PubMed2006

Oxidic or metallic palladium: which is the active phase in pd-catalyzed aerobic alcohol oxidation?

In situ X-ray absorption spectroscopy combined with on-line catalytic measurements using FT-IR spectroscopy unequivocally identified that metallic palladium is the more active phase in the aerobic oxidation of benzyl alcohol than palladium oxide. The aerobic oxidation of benzyl alcohol in cyclohexane at 50 degrees C was low over oxidized 0.5%Pd/Al2O3 and 5%Pd/Al2O3 catalysts. XANES and EXAFS showed that the catalysts in the as-received state were almost fully oxidized and no reduction of the palladium constituent was observed during time-on-stream. After in situ reduction by hydrogen-saturated cyclohexane, the catalysts were much more active (over 50 times) than before reduction. Both XANES and EXAFS uncovered that the palladium constituent was mainly in a reduced state under these conditions of high catalytic activity. This demonstrates that metallic palladium is the active phase for alcohol dehydrogenation.

Journal Article↗
PubMed2006

Discrimination of active palladium sites in catalytic liquid-phase oxidation of benzyl alcohol.

Knowledge of the structure of active sites is a prerequisite for the rational design of solid catalysts. Using site-selective blocking by CO and isotope labeling combined with in situ attenuated total reflection infrared (ATR-IR) spectroscopy, we were able to discriminate the different sites involved in the liquid-phase oxidation of benzyl alcohol on Pd/Al(2)O(3). The main reaction, that is, the oxidative dehydrogenation of the alcohol to the corresponding aldehyde, showed only little dependence on structure and occurred on all exposed Pd faces, whereas the undesired product decarbonylation occurred preferentially on hollow sites on (111) Pd faces. This explains why specific blocking of the latter sites, as realized in the industrially used Pd-Bi/Al(2)O(3) catalysts, leads to improved catalytic performance.

Journal Article↗
PubMed2006

Time-lapse STM studies of diastereomeric cinchona alkaloids on platinum metals.

The adsorption of cinchonidine (CD) and cinchonine (CN) on Pt(111) and Pd(111) single crystals has been investigated by means of scanning tunneling microscopy (STM) in an ultrahigh vacuum system. In time-lapse series the mobilities of different adsorption species have been determined on a single molecule basis and with varying hydrogen background pressures in the system. The diastereomeric cinchona alkaloids, CD and CN, which are widely used as chiral modifiers of platinum group metals in catalytic enantioselective hydrogenation, showed similar adsorption modes and diffusion behavior on Pt(111), except that the flatly adsorbed CN molecules which were free (not in a dimer/cluster) were significantly more mobile than their CD analogues. CD adsorbed on Pd(111) showed similar adsorption modes as observed on Pt(111) but at considerably higher mobility of the flatly absorbed species already in the low-pressure region. The observed adsorption behaviors are discussed in the context of independent ATR-IR measurements and theoretical calculations. Special emphasis is put on the nonlinear effect observed in hydrogenation reactions with CD/CN mixtures. Our observations corroborate that this effect is mainly a consequence of the different adsorption strengths of CD and CN on Pt.

Journal Article↗
PubMed2006

Cinchonidine adsorption on gold and gold-containing bimetallic platinum metal surfaces: an attenuated total reflection infrared and density functional theory study.

Adsorption of cinchonidine on monometallic Au and bimetallic Pt-Au and Pd-Au thin model films prepared by physical vapor deposition has been investigated with attenuated total reflection infrared (ATR-IR) spectroscopy. On Au the alkaloid forms an adsorbed layer that shows higher stability against desorption than the corresponding adsorption on Pt. In this adsorption layer the intermolecular interactions dominate over metal-adsorbate interactions as indicated by the absence of the spectroscopic features attributed to strongly flat adsorbed species. This behavior is further supported by Density Functional Theory (DFT) calculations indicating that flat and tilted orientations of the quinoline ring have comparable adsorption energy on Au but lower (7-10 kcal/mol) compared to adsorption on Pt (ca. 40 kcal/mol). As a consequence, the creation of a metal surface with isolated chiral sites is prevented by formation of an adsorbed structure formed by intermolecularly bound cinchonidine molecules on Au. While the binding to Pt is due to the formation of sigma-bonds to surface atoms, such aggregates are bound to Au mainly by van der Waals forces. Given this different nature of bonding of cinchonidine to Au and Pt, addition of Au to Pt and Pd films could be used to probe the changes of fractional coverage of the different adsorbed species of cinchonidine on the platinum metals. It is demonstrated that the lowering of the domain size of the platinum group metal by Au can simulate the effect of particle size on the distribution of the surface conformations of the alkaloid on a metal surface.

Journal Article↗
PubMed2006

In situ extended X-ray absorption fine structure study during selective alcohol oxidation over Pd/Al2O3 in supercritical carbon dioxide.

High-pressure in situ X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) data are reported during the selective oxidation of benzyl alcohol to benzaldehyde in supercritical carbon dioxide over a Pd/Al(2)O(3) catalyst (shell impregnated). For this purpose, a continuous-flow system with a spectroscopic cell suitable for in situ X-ray absorption studies on heterogeneous catalysts up to 200 degrees C and 200 bar has been developed. Due to the high contribution of the dense fluid to the overall X-ray absorption, high stability of the process pressure is mandatory, particularly when recording EXAFS spectra. According to EXAFS and XANES results, the palladium particles were fully reduced after exposure to benzyl alcohol in scCO(2). In contrast to Pd-catalyzed liquid-phase oxidation, a higher oxygen tolerance of the catalyst was observed. Palladium was partially oxidized on the surface under typical reaction conditions (0.9 mol % benzyl alcohol/0.5 mol % O(2) in carbon dioxide), which gradually increased when the concentration of oxygen in the feed was raised. Both XANES and EXAFS data uncovered that palladium is mainly oxidized on the surface or within the outermost layers. These results are in accordance with simulations of the XANES data using the FEFF8.20 code (program for ab initio calculations on multiple scattering XAS) and EXAFS data fitting/simulation.

Journal Article↗
PubMed2006

Theoretical and spectroscopic study of the effect of ring substitution on the adsorption of anisole on platinum.

The adsorption of anisole, 3,5-dimethylanisole, and 3,5-bis-(trifluoromethyl)-anisole on Pt(111) was studied theoretically and compared to the adsorption of benzene using relativistically corrected density functional theory. A cluster of 31 platinum atoms was used to simulate the surface. The three anisoles were found to be less strongly adsorbed than the parent molecule benzene, 3,5-bis-(trifluoromethyl)-anisole showing weakest adsorption, with an adsorption energy of only one-third that of benzene. The theoretical study was complemented by in situ ATR-IR spectroscopy of the adsorption of the anisole derivatives on a polycrystalline Pt film. The spectroscopic study indicated that the adsorption strength of the anisoles follows the same order as predicted by the calculations. In addition, catalytic hydrogenation tests showed that the propensity to aromatic ring hydrogenation can also be correlated to the mode and strength of adsorption of the anisoles. The degree of saturation followed the same order as the adsorption strength found by the calculations and indicated by spectroscopy. Although 3,5-dimethyl substitution on anisole resulted in only a partial loss of adsorption energy and reactivity toward ring hydrogenation as compared to anisole, the substitution by CF(3) groups led to a large loss of adsorption energy and complete loss of reactivity toward aromatic ring saturation. Along with the study of the substituent effect on the adsorption of aromatic molecules, the correlation between adsorption and propensity to saturation of aromatic substrates could be corroborated.

Journal Article↗
PubMed2006

2D-mapping of the catalyst structure inside a catalytic microreactor at work: partial oxidation of methane over Rh/Al2O3.

Tremendous changes of the structure of Rh particles occurred during partial methane oxidation to hydrogen and carbon monoxide over a 2.5 wt % Rh/Al(2)O(3) catalyst upon ignition of the catalytic reaction. Furthermore, near the ignition temperature a variation in the Rh-valence state along the catalyst bed was observed. By combining hard X-ray absorption spectroscopy (X-ray absorption near edge structure, XANES) with a charged coupled device (CCD) camera and using a suitable spectroscopic cell with gas supply and on-line mass spectrometry, we demonstrate that 2D-mapping of the Rh-oxidation state in a catalyst bed can be achieved during the catalytic reaction. For this purpose, X-ray images were recorded with the CCD camera at each energy around the Rh K-edge with and without the spectroscopic cell. This resulted effectively in the transmitted and incident intensity at each energy and at each pixel of the spectroscopic cell. Reconstruction of the full Rh K-edge XANES spectra at each pixel revealed the local distribution of oxidized and metallic Rh-species in the catalyst bed. Along the catalyst bed, structural changes were found with a steep gradient within less than 100 microm. Furthermore, a characteristic cone toward the inlet of the spectroscopic cell was observed.

Journal Article↗
PubMed2006

ATR-IR spectroscopy of pendant NH2 groups on silica involved in the Knoevenagel condensation.

The liquid-phase Knoevenagel condensation between benzaldehyde and ethyl cyanoacetate catalyzed by aminopropyl-modified silica has been investigated using in situ attenuated total reflection infrared (ATR-IR) spectroscopy. The aim of the work was to demonstrate the different levels of information on the reaction mechanism that can be achieved by operating the spectroscopic cell in the absence and in the presence of a solvent, in flow-through and stop-flow modes and in combination with concentration modulation spectroscopy. The reaction mechanism involves the formation of an imine intermediate whose existence has been verified in situ by combining in one experiment continuous and stop-flow operations. Identical information has been gained more elegantly using concentration modulation spectroscopy, which additionally provided information on the possible origin of the solvent effect observed in the Knoevenagel reaction. Faster production and consumption of the imine intermediate was observed in cyclohexane solvent than in toluene. Identification of other species evolving on the catalyst surface and monitoring of the effluents of the spectroscopic cell provided some insight in possible catalyst deactivation.

Acetates↗
PubMed2006

The origin of chemo- and enantioselectivity in the hydrogenation of diketones on platinum.

In the Pt-catalyzed hydrogenation of 1,1,1-trifluoro-2,4-diketones, addition of trace amounts of cinchonidine, O-methyl-cinchonidine, or (R,R)-pantoyl-naphthylethylamine induces up to 93% ee and enhances the chemoselectivity up to 100% in the hydrogenation of the activated carbonyl group to an OH function. A combined catalytic, NMR and FTIR spectroscopic, and theoretical study revealed that the two phenomena are coupled, offering the unique possibility for understanding the substrate-modifier-metal interactions. The high chemo- and enantioselectivities are attributed to the formation of an ion pair involving the protonated amine function of the chiral modifier and the enolate form of the substrate. DFT calculations including the simulation of the interaction of a protonated amine with the enolate adsorbed on a Pt 31 cluster revealed that only the C-O bond next to the CF3 group of the substrate is in direct contact with Pt and can be hydrogenated. The present study illustrates the fundamental role played by the metal surface and indicates that also the enol form can be the reactive species in the hydrogenation of the activated ketone on chirally modified Pt.

Alcohols↗
PubMed2006

Simultaneous in situ monitoring of surface and gas species and surface properties by modulation excitation polarization-modulation infrared reflection-absorption spectroscopy: CO oxidation over Pt film.

A method for in situ monitoring of surface and gas species utilizing separately the difference and sum reflectivity of two polarizations, normal and parallel to the surface, measured by polarization-modulation infrared reflection-absorption spectroscopy is presented. Surface and gas-phase spectra were separately but simultaneously obtained from the reflectivities. The technique is combined with modulation excitation spectroscopy to further enhance the sensitivity, and a small-volume cell was designed for this purpose. CO oxidation over a 40 nm Pt film on aluminum was investigated under moderate pressure (atmospheric pressure, 5% CO, and 5%-40% O2) at 373-433 K. The surface species involved in the oxidation process and the gas-phase species, both reactant (CO) and product (CO2), could be simultaneously monitored and analyzed quantitatively. In addition, the reflectivity change of the sample during the reaction was assigned to a near-surface bulk property change, that is, surface reconstruction to the oxide phase. Under an O2-rich atmosphere, two reactive phases, denoted as low- and high-activity phases, were identified. A large amount of atop CO was observed during the low-activity phase, while the adsorbed CO completely disappeared during the high-activity phase. The presence of an infrared-inactive CO2 precursor formed by the reaction between surface oxide and gaseous CO during the high-activity phase was inferred. The desorption of the CO2 precursor is facilitated under a CO-rich atmosphere, most likely, by surface reconstruction to metallic Pt and a competitive adsorption of CO on the surface.

Absorption↗
PubMed2006

Solvent-induced conformational changes of O-phenyl-cinchonidine: a theoretical and VCD spectroscopy study.

The conformational analysis of the synthetic chiral modifier O-phenyl-cinchonidine (PhOCD) used in enantioselective hydrogenations over noble metal catalysts has been performed at a PM3 semiempirical level in vacuum. The minimum energy conformations calculated at the DFT level with a medium-size basis set have been compared to those of the parent alkaloid cinchonidine (CD). PhOCD behaves similarly to CD and shows four main conformers, denoted as Closed(1), Closed(2), Open(3), and Open(4). Open(3) is found to be the most stable in vacuum and in CH2Cl2 and CCl4 solvents. A comprehensive normal-mode analysis has been performed for these conformers, and assignment of the infrared spectrum of PhOCD in CCl4 (epsilon = 2.2) has been performed using the calculated spectrum of Open(3), which appears to be the most populated in this solvent. A combined theoretical-experimental VCD spectroscopy approach was used to increase the spectroscopic sensitivity toward changes in the distribution of conformers upon change of solvent polarity. The VCD spectra confirm that Open(3) is by far the most stable conformation in CCl4 (epsilon = 2.2) and indicate that an excess Closed(2) conformer has to be expected in CD2Cl2 (epsilon = 8.9). The possible influence of this conformational behavior is discussed on the basis of available catalytic data and in relation to the enantioselective potential of PhOCD as a chiral modifier on supported metal catalysts.

Cinchona Alkaloids↗
PubMed2005

Supercritical carbon dioxide: an inert solvent for catalytic hydrogenation?

Various surface species originating from the reaction between CO2 and H2 over Al2O3-supported Pt, Pd, Rh, and Ru model catalysts were investigated by attenuated total reflection infrared (ATR-IR) spectroscopy under high-pressure conditions. Two different spectroscopic cells were used: a variable-volume view cell equipped with ATR-crystal and transmission IR windows (batch reactor) and a continuous-flow cell also equipped with a reflection element for ATR-IR spectroscopy. The study corroborated that CO formation from dense CO2 in the presence of hydrogen occurs over all Pt-group metals commonly used in heterogeneous catalytic hydrogenations in supercritical CO2 (scCO2). In the batch reactor cell, formation of CO was detected on all metals at 50 and 90 degrees C, with the highest rate on Pt. Additional surface species were observed on Pt/Al2O3 at 150 bar under static conditions. It seems that further reaction of CO with hydrogen is facilitated by the higher surface concentration at higher pressure. In the continuous-flow cell, CO coverage on Pt/Al2O3 was less prominent than that in the batch reactor cell. A transient experiment in the continuous-flow cell additionally revealed CO formation on Pt/Al2O3 at 120 bar after switching the feed from a H2-ethane to a H2-CO2 mixture. The in situ ATR-IR measurements indicate that CO formation in CO2-H2 mixtures is normally a minor side reaction during hydrogenation reactions on Pt-group metal catalysts, and dense ("supercritical") CO2 may be considered as a relatively "inert" solvent in many practical applications. However, blocking of specific sites on the metal surface by CO and consecutive products can affect structure sensitive hydrogenation reactions and may be at the origin of unexpected shifts in the product distribution.

Journal Article↗
PubMed2005

In situ spectroscopic investigation of heterogeneous catalysts and reaction media at high pressure.

In situ characterization of catalysts by means of complementary spectroscopic techniques can be regarded as the first step towards rational catalyst design. Spurred by the growing interest of catalytic reactions in supercritical fluids and by several industrial reactions traditionally performed at high pressure (>10 bar), new demands and challenges are put to in situ spectroscopic characterization of heterogeneous catalytic reactions. In this article, we discuss the development and the use of spectroscopic and related techniques suitable for elucidating such high-pressure reactions. Selected examples from phase behaviour studies with a view cell, investigations with transmission and attenuated total reflection (ATR) infrared spectroscopy as well as X-ray absorption spectroscopy (EXAFS, XANES), are presented to show the strategies, opportunities and limitations of such high pressure in situ studies. Different facets appear to be important to gain insight into catalytic reactions in supercritical fluids: the identification of the phase behaviour of the reaction mixture, the behaviour of the fluid inside the porous catalyst, the processes occurring at the solid-fluid interface, the possible dissolution of active species and, similar as in gas-solid reactions, the establishment of structure-activity relationships.

Catalysis↗
PubMed2005

Competition at chiral metal surfaces: fundamental aspects of the inversion of enantioselectivity in hydrogenations on platinum.

O-Phenylcinchonidine (PhOCD) is known to efficiently induce inversion of enantioselectivity with respect to cinchonidine (CD) in the enantioselective hydrogenation of various activated ketones on Pt/Al(2)O(3). To understand the origin of the switch of enantioselective properties of the catalyst, the adsorption of PhOCD has been studied by in situ ATR-IR spectroscopy, in the presence of organic solvent and dissolved hydrogen, i.e., under conditions used for catalytic hydrogenation. The adsorption structures and energies of the anchoring group of CD and PhOCD were calculated on a Pt 38 cluster, using relativistically corrected density functional theory (DFT). Both approaches indicate that both modifiers are adsorbed via the quinoline ring and that the spatial arrangement of the quinuclidine skeleton is critical for the chiral recognition. New molecular level information on the conformation of CD relative to PhOCD adsorbed on a surface is extracted from the ATR spectra and supported by DFT calculations. The result is a clearer picture of the role played by the phenyl group in defining the chiral space created by the modifiers on Pt. Moreover, when CD was added to a pre-equilibrated adsorbed layer of PhOCD, a chiral adsorbed layer was formed with CD as the dominant modifier, indicating that CD adsorbs more strongly than PhOCD. Conversely, when PhOCD was added to preadsorbed CD, no significant substitution occurred. The process leading to nonlinear effects in heterogeneous asymmetric catalysis has been characterized by in situ spectroscopy, and new insight into a heterogeneous catalytic R-S switch system is provided.

Adsorption↗
PubMed2005

Interaction of water, alkyl hydroperoxide, and allylic alcohol with a single-site homogeneous Ti-Si epoxidation catalyst: A spectroscopic and computational study.

Tetrakis(trimethylsiloxy)titanium (TTMST, Ti(OSiMe3)4) possesses an isolated Ti center and is a highly active homogeneous catalyst in epoxidation of various olefins. The structure of TTMST resembles that of the active sites in some heterogeneous Ti-Si epoxidation catalysts, especially silylated titania-silica mixed oxides. Water cleaves the Ti-O-Si bond and deactivates the catalyst. An alkyl hydroperoxide, TBHP (tert-butyl hydroperoxide), does not cleave the Ti-O-Si bond, but interacts via weak hydrogen-bonding as supported by NMR, DOSY, IR, and computational studies. ATR-IR spectroscopy combined with computational investigations shows that more than one, that is, up to four, TBHP can undergo hydrogen-bonding with TTMST, leading to the activation of the O-O bond of TBHP. The greater the number of TBHP molecules that form hydrogen bonds to TTMST, the more electrophilic the O-O bond becomes, and the more active the complex is for epoxidation. An allylic alcohol, 2-cyclohexen-1-ol, does not interact strongly with TTMST, but the interaction is prominent when it interacts with the TTMST-TBHP complex. On the basis of the experimental and theoretical findings, a hydrogen-bond-assisted epoxidation mechanism of TTMST is suggested.

Journal Article↗
PubMed2005

Unraveling the surface reactions during liquid-phase oxidation of benzyl alcohol on Pd/Al2O3: an in situ ATR-IR study.

The palladium-catalyzed liquid-phase reaction of benzyl alcohol to benzaldehyde was investigated in the presence and absence of oxygen by attenuated total reflection infrared (ATR-IR) spectroscopy. The 5 wt % Pd/Al2O3 catalyst was fixed in a flow-through ATR-IR cell serving as a continuous-flow reactor. The reaction conditions (cyclohexane solvent, 323 K, 1 bar) were set in the range commonly applied in the heterogeneous catalytic aerobic oxidation of alcohols. The in situ ATR-IR study of the solid-liquid interface revealed a complex reaction network, including dehydrogenation of benzyl alcohol to benzaldehyde, decarbonylation of benzaldehyde, oxidation of hydrogen and CO on Pd, and formation of benzoic acid catalyzed by both Pd and Al2O3. Continuous formation of CO and its oxidative removal by air resulted in significant steady-state CO coverage of Pd during oxidation of benzyl alcohol. Unexpectedly, benzoic acid formed already in the early stage of the reaction and adsorbed strongly (irreversibly) on the basic sites of Al2O3 and thus remained undetectable in the effluent. This observation questions the reliability of product distributions conventionally determined from the liquid phase. The occurrence of the hydrogenolysis of the C-O bond of benzyl alcohol and formation of toluene indicates that Pd was present in a reduced state (Pd0) even in the presence of oxygen, in agreement with the dehydrogenation mechanism of alcohol oxidation.

Journal Article↗
PubMed2004

Flame synthesis of calcium carbonate nanoparticles.

Calcium carbonate nanoparticles of 20-50 nm size were obtained from a flame spray process where combustion of specific calcium-containing precursors results in amorphous or crystalline calcium carbonate particles depending on the spray flow conditions.

Journal Article↗