Biomedical subjects

Andrew J Moore

Publications and source records attributed to Andrew J Moore.

8 recordsLinked to original sources

PubMed2006

Dynamic two-axis curvature measurement using multicore fiber Bragg gratings interrogated by arrayed waveguide gratings.

We describe the use of arrayed waveguide gratings (AWGs) in the interrogation of fiber Bragg gratings (FBGs) for dynamic strain measurement. The ratiometric AWG output was calibrated in a static deflection experiment over a +/-200 microepsilon range. Dynamic strain measurement was demonstrated with a FBG in a conventional single-mode fiber mounted on the surface of a vibrating cantilever and on a piezoelectric actuator, giving a resolution of 0.5 microepsilon at 2.4 kHz. We present results of this technique extended to measure the dynamic differential strain between two FBG pairs within a multicore fiber. An arbitrary cantilever oscillation of the multicore fiber was determined from curvature measurements in two orthogonal axes at 1125 Hz with a resolution of 0.05 m(-1).

Journal Article↗

PubMed2006

High-speed phase-stepped digital speckle pattern interferometry using a complementary metal-oxide semiconductor camera.

A digital speckle pattern interferometer based on a complementary metal-oxide semiconductor (CMOS) camera is described. The temporal evolution of dynamic deformation is measured using interframe phase stepping. The flexibility of the CMOS detector is used to identify regions of interest with full-field time-averaged measurements and then to interrogate those regions with time-resolved measurements sampled at up to 70 kHz. A numerical and analytical investigation shows that the maximum surface velocity that can be reliably measured with interframe phase stepping corresponds to +/-0.3 times the surface velocity at which the interferogram is sampled at the Nyquist limit.

Journal Article↗

PubMed2006

High-speed photogrammetry system for measuring the kinematics of insect wings.

We describe and characterize an experimental system to perform shape measurements on deformable objects using high-speed close-range photogrammetry. The eventual application is to extract the kinematics of several marked points on an insect wing during tethered and hovering flight. We investigate the performance of the system with a small number of views and determine an empirical relation between the mean pixel error of the optimization routine and the position error. Velocity and acceleration are calculated by numerical differencing, and their relation to the position errors is verified. For a field of view of approximately 40 mm x 40 mm, a rms accuracy of 30 mum in position, 150 mm/s in velocity, and 750 m/s2 in acceleration at 5000 frames/s is achieved. This accuracy is sufficient to measure the kinematics of hoverfly flight.

Animals↗

PubMed2005

Process control of laser conduction welding by thermal imaging measurement with a color camera.

Conduction welding offers an alternative to keyhole welding. Compared with keyhole welding, it is an intrinsically stable process because vaporization phenomena are minimal. However, as with keyhole welding, an on-line process-monitoring system is advantageous for quality assurance to maintain the required penetration depth, which in conduction welding is more sensitive to changes in heat sinking. The maximum penetration is obtained when the surface temperature is just below the boiling point, and so we normally wish to maintain the temperature at this level. We describe a two-color optical system that we have developed for real-time temperature profile measurement of the conduction weld pool. The key feature of the system is the use of a complementary metal-oxide semiconductor standard color camera leading to a simplified low-cost optical setup. We present and discuss the real-time temperature measurement and control performance of the system when a defocused beam from a high power Nd:YAG laser is used on 5 mm thick stainless steel workpieces.

Journal Article↗

PubMed2005

Transverse load and orientation measurement with multicore fiber Bragg gratings.

We demonstrate the sensitivity of Bragg gratings in a multicore fiber to transverse load. The Bragg peaks are split because of stress-induced birefringence, the magnitude of which depends upon the load and grating position relative to the load axis. Experiments show that a set of gratings in a four-core fiber can measure a load axis angle to +/- 5 degrees and a load magnitude to +/- 15 N m(-1) up to 2500 N m(-1). We consider alternative designs of multicore fiber for optimal load sensing and compare experimental and modeled data.

Journal Article↗

PubMed2005

Volume three-dimensional flow measurements using wavelength multiplexing.

Optically distinguishable seeding particles that emit light in a narrow bandwidth, and a combination of bandwidths, were prepared by encapsulating quantum dots. The three-dimensional components of the particles' displacement were measured within a volume of fluid with particle tracking velocimetry (PTV). Particles are multiplexed to different hue bands in the camera images, enabling an increased seeding density and (or) fewer cameras to be used, thereby increasing the measurement spatial resolution and (or) reducing optical access requirements. The technique is also applicable to two-phase flow measurements with PTV or particle image velocimetry, where each phase is uniquely seeded.

Algorithms↗

PubMed2004

Differential birefringence in Bragg gratings in multicore fiber under transverse stress.

We present experimental measurements of the peak splitting of the reflection spectra of fiber Bragg gratings as a result of birefringence induced by transverse loading of a multicore fiber. Measurements show that the splitting is a function of the applied load and the direction of the load relative to the azimuth of the fiber. A model for calculating the stress in the fiber that is due to an applied load is in good agreement with our experimental observations.

Journal Article↗

PubMed2002

Closed-loop phase stepping in a calibrated fiber-optic fringe projector for shape measurement.

Active homodyne feedback control can be used to stabilize an interferometer against unwanted phase drifts introduced by, for example, temperature gradients. The technique is commonly used in fiber-optic sensors to maintain the fiber at its most sensitive (quadrature) position. We describe an extension of the technique to introduce stabilized, pi/2-rad phase steps in a full-field interferometer. The technique was implemented in a single-mode, fiber-optic interference fringe projector used for shape measurement and can be easily applied to other fiber- or bulk-optic interferometers, for example, speckle pattern and holographic interferometers. Fresnel reflections from the distal fiber ends undergo a double pass in the fibers and interfere at the fourth port of a directional coupler. The interference intensity (and hence phase) is maintained at quadrature by feedback control to a phase modulator in one of the fiber arms. Stepping between quadrature positions (separated by pi rad for light undergoing a double pass) introduces stabilized phase steps in the projected fringes (separated by pi/2 rad for a single pass). A root-mean-square phase stability of 0.61 mrad in a 50-Hz bandwidth and phase step accuracy of 1.17 mrad were measured.

Journal Article↗