PubMed Health⌕ Search

Biomedical subjects

B Kasemo

Publications and source records attributed to B Kasemo.

At least 19 recordsLinked to original sources

A multitechnique study of liposome adsorption on Au and lipid bilayer formation on SiO2.

We have used a new setup for parallel quartz crystal microbalance with dissipation (QCM-D) and surface plasmon resonance (SPR) measurements to measure the detailed kinetics of vesicle-to-bilayer transformation on SiO2 and vesicle adsorption on Au, respectively. The combination of SPR and QCM-D, complemented by atomic force microscopy measurements, has enabled a complete, time-resolved separation of vesicle and bilayer coverages, and thus, for the first time, allowed precise quantification of the critical surface coverage of vesicles needed for rupture. We furthermore demonstrate and quantify a previously undetected vesicle-size- and concentration-dependent loss of lipid material during the later stages of the process.

Adsorption↗

Imaging and manipulation of adsorbed lipid vesicles by an AFM tip: experiment and Monte Carlo simulations.

Single lipid vesicles adsorbed on SiO(2) were manipulated using an atomic force microscope (AFM) operated in contact mode. For large force setpoints, single vesicles were either pushed sideways or ruptured by the tip, depending on the tip type (sharp or blunt) used, while for small force setpoints the vesicles were imaged by the tip. To extend the interpretation of and to guide the experiment, we have developed a generic model of the vesicle-tip-substrate system and performed Monte Carlo simulations, addressing the influence of force setpoint and tip speed and shape on the type of imaging or manipulation observed. Specifically, we have explored AFM-image height and width variations versus force setpoint, typical AFM images for small and large force setpoints, tip-induced vesicle strain versus force setpoint, typical vesicle shapes during pushing for different tip speeds, and the details of vesicle rupture induced by the tip.

Adsorption↗

Transient and steady state CO oxidation kinetics on nanolithographically prepared supported Pd model catalysts: experiments and simulations.

Applying molecular-beam methods to a nanolithographically prepared planar PdSiO2 model catalyst, we have performed a detailed study of the kinetics of CO oxidation. The model catalyst was prepared by electron-beam lithography, allowing individual control of particle size and position. The sample was structurally characterized by atomic force microscopy and scanning electron microscopy before and after reaction. In the kinetic experiments, the O-rich and CO-rich regimes were investigated systematically with respect to their transient and steady-state behaviors, both under bistable and monostable reaction conditions. Separate molecular beams were used in order to supply the reactants, allowing individual control over the reactant fluxes. The desorbing CO2 was detected by both angle-resolved and angle-integrated mass spectrometries. The experimental results were analyzed using different types of microkinetic models, including a detailed reaction-diffusion model, which takes into account the structural parameters of the catalyst as well as scattering of the reactants from the support. The model quantitatively reproduces the results as a function of the reactant fluxes and the surface temperature. Various kinetic effects observed are discussed in detail on the basis of the model. Specifically, it is shown that under conditions of limited oxygen mobility, the switching behavior between the kinetic regimes is largely driven by the surface mobility of CO.

Journal Article↗

Local reaction rates and surface diffusion on nanolithographically prepared model catalysts: experiments and simulations.

Combining molecular beam methods and angular resolved mass spectrometry, we have studied the angular distribution of desorbing products during CO oxidation on a planar Pd/silica supported model catalyst. The model catalyst was prepared by means of electron beam lithography, allowing individual control of particle size, position, and aspect ratio, and was characterized by atomic force microscopy and scanning electron microscopy before and after reaction. In the experiment, both oxygen and CO rich regimes were investigated using separate molecular beams for the two reactants. This allows exploration of diffusion effects of reactants on the particles and of shadowing and backscattering phenomena. A reaction-diffusion model was developed in order to extract information about local reaction rates on the surface of the catalyst nanoparticles. The model takes into account the structural parameters of the catalyst as well as the backscattering of the reactants and products from the support. It allows a quantitative description of the experimental data and provides a detailed understanding of temperature and reactant flux dependent effects. Moreover, information on the surface mobility of oxygen under steady-state reaction conditions could be obtained by comparison with the experimental results.

Journal Article↗

Two-dimensional hydration shells of alkali metal ions at a hydrophobic surface.

We study the hydration shell formation of alkali metal ions at a graphite surface. Two-dimensional shell structures are found in the initial stage of hydration, in contrast to the three-dimensional structures in bulk water and clusters. Comparison of vibrational spectra with experiments identifies the shell structures and the thermally induced transition from the first to the second shell. We also found intriguing competition between hydration and ion-surface interaction, leading to different solvation dynamics between K and Na. Implications of these results in ionic processes at interfaces are elaborated.

Journal Article↗

Simulations of temperature dependence of the formation of a supported lipid bilayer via vesicle adsorption.

Recent experimental investigations of the kinetics of vesicle adsorption in solution on SiO2 demonstrate a thermally activated transition from adsorbed intact vesicles to a supported lipid bilayer. Our Monte Carlo simulations clarify the mechanism of this process. The model employed is an extension of the model used earlier to describe vesicle adsorption at room temperature. Specifically, it includes limitations of the adsorption rate by vesicle diffusion in the solution, and adsorption- and lipid-membrane-induced rupture of arriving and already adsorbed vesicles. Vesicles and lipid molecules, formed after rupture of vesicles, are considered immobile. With these ingredients, the model is able to quantitatively reproduce the temperature-dependent adsorption kinetics, including a higher critical surface concentration of intact vesicles for lower temperatures, and the apparent activation energy for the vesicle-to-bilayer transition E(a) approximately 5 kcal/mol.

Adsorption↗

Fluctuations and bistabilities on catalyst nanoparticles.

We show that coverage fluctuations on catalyst particles can drastically alter their macroscopic catalytic behavior. Scrutinizing the occurrence of kinetic bistabilities, it is demonstrated by molecular beam experiments on model catalysts that macroscopically observable bistabilities vanish completely with decreasing particle size, as previously predicted by theory. The effect is attributed to fluctuation-induced transitions between two kinetic reaction regimes, with a transition rate controlled by both particle size and surface defects. These results suggest that fluctuation-induced effects represent a general phenomenon affecting the reaction kinetics on nanostructured surfaces.

Journal Article↗

Kinetics of protein aggregation with formation of unreactive intermediates.

Irreversible protein aggregation resulting in formation and deposition of insoluble fibrils or amorphous precipitates is usually assumed to occur via sequential attachment of monomers to soluble intermediates. We complement this scheme by slow conversion of the intermediates to a relatively stable form so that they do not react with monomers but can be trapped by precipitates. For reasonable values of parameters, our model predicts that the aggregation kinetics order may be between 2.0 and 2.5. In particular, the model can be used to explain the reaction order, 2.17 +/- 0.09, observed for aggregation of recombinant human granulocyte colony stimulating factor.

Kinetics↗

Chemically patterned, metal oxide based surfaces produced by photolithographic techniques for studying protein- and cell-surface interactions I: Microfabrication and surface characterization.

Chemical patterns on smooth wafer substrates comprising areas with two different metals have been produced by vacuum metal deposition and photolithographic techniques. The combination of metals has been chosen from the series titanium (Ti), aluminium (Al), vanadium (V) and niobium (Nb), producing patterns (dots and stripes with dimensions of 50, 100 and 150 micrometer) with one of the metals as the background and with the second metal (foreground pattern) deposited on the background metal. The structure and chemical composition of the patterned surfaces were evaluated by scanning electron microscopy, X-ray photoelectron spectroscopy and imaging time-of-flight secondary-ion mass spectrometry. The surfaces proved to be geometrically well defined with the expected surface-chemical composition, i.e. a surface oxide (passive) film essentially composed of TiO(2),Al(2)O(3),V(2)O(5), or Nb(2)O(5). Ti/Ti patterned surfaces were produced as controls and found to show no chemical composition contrast. The surface roughness of the pattern was greater than that of the background by a factor of 2-3, but was still extremely smooth with Ra<2nm. The patterns serve as model surfaces for studying in vitro the behaviour of cells as well as the adsorption of serum proteins on different metal oxides, which will be reported in a companion paper. These surfaces can be used to compare and contrast the response of osteoblasts to Ti and other alloy components, such as Al, V, or Nb, which are used in load-bearing medical implants.

Aluminum↗

Temperature dependence of formation of a supported phospholipid bilayer from vesicles on SiO2.

Adsorption of egg-phosphatidylcholine vesicles and bilayer formation on a SiO2 surface was investigated in the temperature range 278-303 K using the quartz crystal microbalance-dissipation technique. The critical coverage for the vesicle-->bilayer transition is found to decrease with increasing temperature. The temperature dependence of the time-scale characterizing this transition can be represented in the Arrhenius form. Higher temperatures produce a bilayer with fewer trapped, nonruptured vesicles.

Biophysical Phenomena↗

Missing mass effect in biosensor's QCM applications.

Nowadays, liquid applications of quartz crystal microbalance (QCM) opened a way for in situ studies of proteins, vesicles and cells adsorbed from the solution onto the QCM surface. The sensitivity of QCM to the viscoelasticity of the adsorbed biomaterial can be a reason of the experimentally observed deviation from a linear dependence of QCM resonant frequency on mass deposition (the so-called Sauerbrey relation) and can limit its application for biosensoring. Presented here rigorous theoretical analysis explains the deviation from ideal mass response of soft overlayers in the contact with liquid. The fundamental result of the theory is the analog of Sauerbrey relation for layered viscous/viscoelastic medium which can be exploited for the correct physical interpretation of QCM experimental data in biofluids, in particular for measurements of the 'true' surface mass of adsorbed biomolecular films. We predict a new physical effect 'missing mass' of the sample in liquid phase measurements and compare the results given by our theory with QCM measurements on supported membranes.

Adsorption↗

Variations in coupled water, viscoelastic properties, and film thickness of a Mefp-1 protein film during adsorption and cross-linking: a quartz crystal microbalance with dissipation monitoring, ellipsometry, and surface plasmon resonance study.

We have measured the time-resolved adsorption kinetics of the mussel adhesive protein (Mefp-1) on a nonpolar, methyl-terminated (thiolated) gold surface, using three independent techniques: quartz crystal microbalance with dissipation monitoring (QCM-D), surface plasmon resonance, and ellipsometry. The QCM-D and ellipsometry data shows that, after adsorption to saturation of Mefp-1, cross-linking of the protein layer using NaIO4 transforms it from an extended (approximately 20 nm), water-rich, and hydrogel-like state to a much thinner (approximately 5 nm), compact, and less water-rich state. Furthermore, we show how quantitative data about the thickness, shear elastic modulus, and shear viscosity of the protein film can be obtained with the QCM-D technique, even beyond the Sauerbrey regime, if frequency (f) and energy dissipation (D) measurements measured at multiple harmonics are combined with theoretical simulations using a Voight-based viscoelastic model. The modeling result was confirmed by substituting H2O for D2O. As expected, the D2O substitution does not influence the actual adsorption behavior, but resulted in expected differences in the estimated effective density and shear viscosity. These results provide new insight and understanding about the adsorption kinetics and crosslinking behavior of Mefp-1. They also demonstrate how the above three techniques complement each other for biomolecule adsorption studies.

Adsorption↗

Simulation of two-dimensional streptavidin crystallization.

We present lattice Monte Carlo simulations of the growth of streptavidin islands at a biotinylated lipid layer. The model employed takes into account attractive anisotropic lateral interactions between streptavidin tetramers. With a minimal set of interactions, we reproduce the formation of rectangular islands experimentally observed at pH > or = 9.0. Specifically, we analyze two scenarios of the island growth. First, if streptavidin is rapidly adsorbed at t = 0 (stepwise coverage change without ongoing adsorption), the average linear island size is found to grow according to the Lifshitz-Slyozov law, R proportional to t(1/3). Second, if the island growth occurs in parallel with streptavidin adsorption limited by diffusion in the solution, the Lifshitz-Slyozov law is also applicable, but only at the late stage, when the streptavidin coverage is appreciable.

Adsorption↗

Folding of bundles of alpha-helices in solution, membranes, and adsorbed overlayers.

We propose a coarse-grained lattice model for Monte Carlo simulations of folding of proteins consisting of several alpha-helices. A chain representing a protein is considered to contain A and B monomers forming relatively stiff A subchains, mimicking helices, and flexible B links between these subchains, respectively. Using this model, we simulate (1) folding of four-helix proteins in solution; (2) folding of membrane proteins containing one, two, or four helices; and (3) refolding of four-helix proteins adsorbed at the liquid-solid interface. For these cases, we show typical scenarios of protein folding and refolding and study the dependence of the folding time on the chain length. Combining the latter results with those already available in the literature, we discuss the relative rates of folding of proteins belonging to different classes.

Algorithms↗

Ordering of adsorbed proteins.

Adapting a hard hexagon model to describing protein adsorption, we show by using Monte Carlo simulations that the ordering of adsorbed proteins may strongly depend on the relative location of the hydrophilic and hydrophobic patches on their surface. Specifically, proteins may form dimers, trimers, small rings, and zig-zag or straight chains or islands consisting of such fragments.

Adsorption↗

Formation of supported membranes from vesicles.

Using a combination of the quartz crystal microbalance and surface plasmon resonance techniques, we have studied the spontaneous formation of supported lipid bilayers from small (approximately 25 nm) unilamellar vesicles. Together these experimental methods measure the amount of lipid adsorbed on the surface and the amount of water trapped by the lipid. With this approach, we have, for the first time, been able to observe in detail the progression from the adsorption of intact vesicles to rupture and bilayer formation. Monte Carlo simulations reproduce the data.

Adsorption↗

Monte Carlo simulation of diffusion of adsorbed proteins.

We present the results of three-dimensional lattice Monte Carlo simulations of protein diffusion on the liquid-solid interface in a wide temperature range including the most interesting temperatures (from slightly below T(f) and up to T(c), where T(f) and T(c) are the folding and collapse temperatures). For the model under consideration (27 monomers of two types), the temperature dependence of the diffusion coefficient is found to obey the Arrhenius law with the normal value (approximately 10(-2)-10(-3) cm(2)/s) of the preexponential factor. Proteins 2000;39:76-81.

Adsorption↗

Adsorption and coadsorption of water and glycine on TiO2.

Adsorption of water, ions, and biomolecules constitutes the first events occurring at biomaterial-biosystem interfaces. In this work, the adsorption and coadsorption of water and glycine on TiO2 were studied by thermal desorption spectroscopy (TDS). The first water monolayer desorbs in three peaks around 180K, 300K, and 400K, which are assigned to water molecularly adsorbed at oxygen sites, at Ti4+ sites, and to recombination of dissociated water, respectively. A fourth desorption peak (160K), appearing at coverages > 0.8 monolayer, is attributed to water clusters and multilayers. The water-TiO2 interaction is changed if the surface is annealed in vacuum, which leads to increased hydroxylation. Desorption spectra from glycine overlayers evaporated on TiO2 in situ show that around 40% of the first monolayer desorbs as intact molecules ( approximately 300-450 K) and the remainder as dissociation fragments and surface reaction products around 600 K. At coverages > 0.6 monolayers, intact molecules desorbing from cluster multilayers at 310 K are detected. The glycine desorption spectra are unaffected by coadsorbed water. In contrast, coadsorption of glycine displaces water from more strongly bound states in the monolayer to more weakly bound states and clusters, making the surface more hydrophobic. The study shows that TDS is a powerful method for characterizing biomaterial surfaces with regard to their interaction with biologically relevant molecules.

Adsorption↗