Biomedical subjects

B M Wilén

Publications and source records attributed to B M Wilén.

7 recordsLinked to original sources

PubMed2006

Influence of flocculation and settling properties of activated sludge in relation to secondary settler performance.

Floc characteristics were studied at a full scale activated sludge treatment plant with a unique process solution incorporating pre-denitrification with post-nitrification in nitrifying trickling filters. Since greater nitrogen removal is achieved when more secondary settled wastewater is recirculated to the trickling filters, the secondary settlers are always operated close to their maximal capacity. The flocculation and settling properties are therefore crucial and have an effect on the overall plant performance. Since the plant is operated at a short sludge age, these properties change quickly, resulting in variable maximal secondary settler capacity. The dynamics in floc structure and microbial community composition were studied and correlated to the secondary settler performance. Fluorescence in situ hybridisation was used to investigate the microbial community structure and their spatial distribution. The floc structure could to some extent be related to the flocculation and settling properties of the sludge. Even small differences had an influence suggesting that colloidal properties also play a significant role in determining the floc properties. No correlation between microbial community composition and settling properties could be established with the group-specific probes investigated.

Environmental Restoration and Remediation↗

PubMed2006

Rain events and their effect on effluent quality studied at a full scale activated sludge treatment plant.

The effect of rain events on effluent quality dynamics was studied at a full scale activated sludge wastewater treatment plant which has a process solution incorporating pre-denitrification in activated sludge with post-nitrification in trickling filters. The incoming wastewater flow varies significantly due to a combined sewer system. Changed flow conditions have an impact on the whole treatment process since the recirculation to the trickling filters is set by the hydraulic limitations of the secondary settlers. Apart from causing different hydraulic conditions in the plant, increased flow due to rain or snow-melting, changes the properties of the incoming wastewater which affects process performance and effluent quality, especially the particle removal efficiency. A comprehensive set of on-line and laboratory data were collected and analysed to assess the impact of rain events on the plant performance.

Nitrogen↗

PubMed2004

Dynamics in maximal settling capacity in an activated sludge treatment plant with highly loaded secondary settlers.

Secondary settling dynamics at maximal capacity were investigated at a full scale wastewater treatment plant which utilizes a unique process solution incorporating pre-denitrification with post-nitrification in nitrifying trickling filters. Since nitrogen removal is greater when more secondary effluent is recirculated to the trickling filters, the secondary settlers generally operate at close to their maximal capacity. The settling and flocculation properties of the activated sludge are therefore a major capacity-determining factor for plant operation. Due to the short sludge age, the flocculation properties, with respect to both thickening and clarification, can change quickly. The dynamics in these changes were studied and the factors that determine the maximal settling capacity were assessed. Solids flux curves were constructed from batch settling tests and compared with the actual maximal settling capacities.

Bioreactors↗

PubMed2004

Mass transfer impacts in flocculent and granular biomass from SBR systems.

An experimental study was conducted to describe mass transfer impacts within nitrifying aggregates sourced from sequencing batch reactor (SBR) activated sludge systems. Flocculent and granular sludge with high nitrification activity was obtained in two laboratory SBR systems, supplied with a synthetic, ammonium-based feed. The flocculent biomass was fractionated using a sieving procedure, in order to obtain biomass fractions with different particle size distributions. The oxygen uptake rate (OUR) response to changes in dissolved oxygen concentration was measured under highly controlled conditions in a titrimetric and off-gas analysis (TOGA) sensor, and the results used to assess mass transfer effects. As the average particle size of the biomass increased, mass transfer limitations were found to increase significantly. Empirically fitted, apparent K(S,O2) values were demonstrated to be highly dependent on particle size, and reflect the mass transfer limitations occurring in the aggregates within a given system. Such parameters thus have little to do with the actual biokinetic parameter from which they are derived. The results obtained from the TOGA sensor study were consistent with those obtained from a microelectrode study on the same nitrifying granules. Together, these studies add considerable weight to the conclusion that consideration of external and internal mass transfer limitations is vital to the accurate description of activated sludge treatment processes, particularly those with a high oxygen uptake rate.

Biomass↗

PubMed2004

Structure and microbial composition of nitrifying microbial aggregates and their relation to internal mass transfer effects.

This paper presents an analysis of the structure and microbial composition of nitrifying aggregates, formed as either flocs or granules, in sequencing batch reactors (SBR) operated with a high ammonium load. The structure and microbial community of the aggregates was determined by fluorescence in situ hybridisation (FISH). The aggregate structure and size was related to mass transfer limitations observed by measurements of OURs measured by either a titrimetric and off-gas analysis sensor (TOGA) or by microsensors. The FISH analysis showed that the spatial arrangement of the microbial consortia correlated well with the oxygen gradients inside the aggregates. In the larger aggregates, the ammonium- and nitrite-oxidising bacteria were mainly concentrated to the outer 100-200 microm, whereas in the floc system, the bacteria were distributed throughout the entire aggregate. This indicates that the internal mass transfer resistance is considerably larger when the aggregate size increases which is directly supported by TOGA measurements.

Bacteria↗

PubMed2003

Relationship between flocculation of activated sludge and composition of extracellular polymeric substances.

Activated sludge flocs are a flocculated mass of microorganisms, extracellular polymeric substances (EPS) and adsorbed organic and inorganic material. The structure of the floc is very heterogeneous and flocs with very different properties and morphologies may occur, depending on the conditions in the activated sludge treatment plant and wastewater composition. Present thinking suggest that cations, such as calcium, create cationic bridges with EPS excreted by the bacteria and thereby hold the various floc constituents together. However, due to the complex and heterogeneous nature of activated sludge, the mechanisms have neither been thoroughly investigated nor successfully quantified. A better understanding and description of the biological flocculation process is necessary in order to establish more efficient operational strategies. The main aim of this study was to get a comprehensive and unique insight into the floc properties of activated sludge and to assess the relative impact of chemical and physical parameters. A variety of sludges from full scale treatment plants with different settling properties were characterised. The interrelationships between floc parameters such as composition of EPS, surface properties and floc structure, and their effect on the flocculation and separation properties were assessed. The results indicate that the EPS, both in terms of quantity and quality, are very important for the floc properties of the activated sludge. However, presence of filaments may alter the physical properties of the flocs considerably. The EPS showed positive correlations to sludge volume index (SVI) if only sludges with low or moderate numbers of filaments were included. The surface properties were more affected by the composition of the EPS than by the number of filaments. The EPS showed positive correlation to negative surface charge and a negative correlation to relative hydrophobicity and flocculation ability. The negative correlation between flocculation ability and amount of EPS was surprising. The shear sensitivity, measured as degree of erosion of flocs when subjected to shear, was more affected by floc size and number of filaments than amount of EPS.

Bacteria↗

PubMed2002

Modelling the activated sludge flocculation process combining laser light diffraction particle sizing and population balance modelling (PBM).

A technique based on laser light diffraction is shown to be successful in collecting on-line experimental data. Time series of floc size distributions (FSD) under different shear rates (G) and calcium additions were collected. The steady state mass mean diameter decreased with increasing shear rate G and increased when calcium additions exceeded 8 mg/l. A so-called population balance model (PBM) was used to describe the experimental data. This kind of model describes both aggregation and breakage through birth and death terms. A discretised PBM was used since analytical solutions of the integro-partial differential equations are non-existing. Despite the complexity of the model, only 2 parameters need to be estimated; the aggregation rate and the breakage rate. The model seems, however, to lack flexibility. Also, the description of the floc size distribution (FSD) in time is not accurate.

Flocculation↗