PubMed Health⌕ Search

Biomedical subjects

B S Hsiao

Publications and source records attributed to B S Hsiao.

5 recordsLinked to original sources

Thermally induced phase transitions and morphological changes in organoclays.

Thermal transitions and morphological changes in Cloisite organoclays were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), Fourier transform infrared (FTIR) spectroscopy, and in situ simultaneous small-angle X-ray scattering (SAXS) and wide-angle X-ray diffraction (WAXD) over the temperature range of 30-260 degrees C. On the basis of DSC and FTIR results, the surfactant component in organoclays was found to undergo a melting-like order-disorder transition between 35 and 50 degrees C. The transition temperatures of the DSC peaks (Ttr) in the organoclays varied slightly with the surfactant content; however, they were significantly lower than the melting temperature of the free surfactant (dimethyldihydrotallowammonium chloride; Tm = 70 degrees C). FTIR results indicated that within the vicinity of Ttr, the gauche content increased significantly in the conformation of surfactant molecules, while WAXD results did not show any change in three-dimensional ordering. Multiple scattering peaks were observed in SAXS profiles. In the SAXS data acquired below Ttr, the second scattering peak was found to occur at an angle lower than twice that of the first peak position (i.e., nonequidistant scattering maxima). In the data acquired above Ttr, the second peak was found to shift toward the equidistant position (the most drastic shift was seen in the system with the highest surfactant content). Using a novel SAXS modeling technique, we suggest that the appearance of nonequidistant SAXS maxima could result from a bimodal layer thickness distribution of the organic layers in organoclays. The occurrence of the equidistant scattering profile above Ttr could be explained by the conversion of the bimodal distribution to the unimodal distribution, indicating a redistribution of the surfactant that is nonbounded to the clay surface. At temperatures above 190 degrees C, the scattering maxima gradually broadened and became nonequidistant again but having the second peak shifted toward a scattering angle higher than twice the first peak position. The changes in SAXS patterns above 190 degrees C could be attributed to the collapse of organic layers due to desorption and/or degradation of surfactant component, which was supported by the TGA data.

Journal Article↗

Development of a nanostructured DNA delivery scaffold via electrospinning of PLGA and PLA-PEG block copolymers.

The present work utilizes electrospinning to fabricate synthetic polymer/DNA composite scaffolds for therapeutic application in gene delivery for tissue engineering. The scaffolds are non-woven, nano-fibered, membranous structures composed predominantly of poly(lactide-co-glycolide) (PLGA) random copolymer and a poly(D,L-lactide)-poly(ethylene glycol) (PLA-PEG) block copolymer. Release of plasmid DNA from the scaffolds was sustained over a 20-day study period, with maximum release occurring at approximately 2 h. Cumulative release profiles indicated amounts released were approximately 68-80% of the initially loaded DNA. Variations in the PLGA to PLA-PEG block copolymer ratio vastly affected the overall structural morphology, as well as both the rate and efficiency of DNA release. Results indicated that DNA released directly from these electrospun scaffolds was indeed intact, capable of cellular transfection, and successfully encoded the protein beta-galactosidase. When tested under tensile loads, the electrospun polymer/DNA composite scaffolds exhibited tensile moduli of approximately 35 MPa, with approximately 45% strain initially. These values approximate those of skin and cartilage. Taken together, this work represents the first successful demonstration of plasmid DNA incorporation into a polymer scaffold using electrospinning.

Animals↗

Dislocation-controlled perforated layer phase in a PEO- b-PS diblock copolymer.

Small angle x-ray analyses show that the shear-induced hexagonal perforated layer phase in a poly(ethylene oxide)- b-polystyrene diblock copolymer consists of trigonal (R3;m) twins and a hexagonal (P6(3)/mmc) structure, with trigonal twins being majority components. Transmission electron microscopy reveals that the hexagonal structure is generated through sequential intrinsic stacking faults on the second layer from a previous edge dislocation line, while the trigonal twins are formed by successive intrinsic stacking faults on neighboring layers due to the plastic deformation under mechanical shear.

Journal Article↗

A novel approach to extract morphological variables in crystalline polymers from time-resolved synchrotron SAXS data.

A novel approach to extract morphological variables in crystalline polymers from time-resolved SAXS data using the method of correlation and interface distribution functions has been devised. The principle of the calculation is based on two alternative expressions of Porod's law using the form of the interference function. The approach enables the continuous estimate of the Porod constant, and corrections for liquid scattering and finite interface between the two phases, from the time-resolved data. A model of lamellar morphology has been implemented to interpret the calculated correlation and interface distribution functions. Many detailed morphological variables such as lamellar long period, thicknesses of crystal and amorphous phases, interface thickness, and scattering invariant can be estimated. An example analysis of isothermal crystallization in PET measured by synchrotron SAXS is demonstrated.

Journal Article↗