Biomedical subjects

Baikun Li

Publications and source records attributed to Baikun Li.

4 recordsLinked to original sources

PubMed2005

The impact of ultraviolet light on bacterial adhesion to glass and metal oxide-coated surface.

Biofouling of glass and quartz surfaces can be reduced when the surface is coated with photocatalytically active metal oxides, such as TiO2 (anatase form) or SnO2. We measured the attachment of eight strains of bacteria to these two metal oxides (TiO2 and SnO2), and to an uncoated glass (control; designated Si-m) before and after exposure to UV light at wavelengths of 254 nm (UVC) or 340 nm UV (UVA). TiO2-coated surfaces were photocatalytically active at both 254 and 340 nm as evidenced by a decrease in the water contact angle of the surface from 59 degrees +/-2 to <5 degrees. The water contact angle of the SnO2 surface was reduced only at 254 nm, while contact angle of the Si-m glass surface was not altered by light of either wavelength. Bacterial adhesion decreased by 10-50% to photocatalyzed glass surfaces. In all cases, bacteria exposed to the UV light were completely killed due to a combination of exposure to UV light and the photocatalytic activity of the glass surfaces. These results show that UV light irradiation of TiO2-coated surfaces can be an effective method of reducing bacterial adhesion.

Bacillus subtilis↗

PubMed2004

Bacterial adhesion to glass and metal-oxide surfaces.

Metal oxides can increase the adhesion of negatively-charged bacteria to surfaces primarily due to their positive charge. However, the hydrophobicity of a metal-oxide surface can also increase adhesion of bacteria. In order to understand the relative contribution of charge and hydrophobicity to bacterial adhesion, we measured the adhesion of 8 strains of bacteria, under conditions of low and high-ionic strength (1 and 100 mM, respectively) to 11 different surfaces and examined adhesion as a function of charge, hydrophobicity (water contact angle) and surface energy. Inorganic surfaces included three uncoated glass surfaces and eight metal-oxide thin films prepared on the upper (non-tin-exposed) side of float glass by chemical vapor deposition. The Gram-negative bacteria differed in lengths of lipopolysaccharides on their outer surface (three Escherichia coli strains), the amounts of exopolysaccharides (two Pseudomonas aeruginosa strains), and their known relative adhesion to sand grains (two Burkholderia cepacia strains). One Gram positive bacterium was also used that had a lower adhesion to glass than these other bacteria (Bacillus subtilis). For all eight bacteria, there was a consistent increase in adhesion between with the type of inorganic surface in the order: float glass exposed to tin (coded here as Si-Sn), glass microscope slide (Si-m), uncoated air-side float glass surface (Si-a), followed by thin films of (Co(1-y-z)Fe(y)Cr(z))3O4, Ti/Fe/O, TiO2, SnO2, SnO2:F, SnO2:Sb, A1(2)O3, and Fe2O3 (the colon indicates metal doping, a slash indicates that the metal is a major component, while the dash is used to distinguish surfaces). Increasing the ionic strength from 1 to 100 mM increased adhesion by a factor of 2.0 +/- 0.6 (73% of the sample results were within the 95% CI) showing electrostatic charge was important in adhesion. However, adhesion was not significantly correlated with bacterial charge and contact angle. Adhesion (A) of the eight strains was significantly (P < 10(-25)) correlated with total adhesion free energy (U) between the bacteria and surface (A = 2162e(-1.8U)). Although the correlation was significant, agreement between the model and data was poor for the low energy surfaces (R2 = 0.68), indicating that better models or additional methods to characterize bacteria and surfaces are still needed to more accurately describe initial bacterial adhesion to inorganic surfaces.

Bacillus subtilis↗

PubMed2004

Micro-profiles of activated sludge floc determined using microelectrodes.

The microbial activity within activated sludge floc is a key factor in the performance of the activated sludge process. In this study, the microenvironment of activated sludge flocs from two wastewater treatment plants (Mill Creek Wastewater Treatment Plant and Muddy Creek Wastewater Treatment Plant, with aeration tank influent CODs of 60-120 and 15-35 mg/L, respectively) were studied by using microelectrodes. Due to microbial oxygen utilization, the aerobic region in the activated sludge floc was limited to the surface layer (0.1-0.2mm) of the sludge aggregate at the Mill Creek plant. The presence of an anoxic zone inside the sludge floc under aerobic conditions was confirmed in this study. When the dissolved oxygen (DO) in the bulk liquid was higher than 4.0mg/L, the anoxic zone inside the activated sludge floc disappeared, which is helpful for biodegradation. At the Muddy Creek plant, with its lower wastewater pollutant concentrations, the redox potential and DO inside the sludge aggregates were higher than those at the Mill Creek plant. The contaminant concentration in the bulk wastewater correlates with the oxygen utilization rate, which directly influences the oxygen penetration inside the activated sludge floc, and results in redox potential changes within the floc. The measured microprofiles revealed the continuous decrease of nitrate concentration inside the activated sludge floc, even though significant nitrification was observed in the bulk wastewater. The oxygen consumption and nitrification rate analyses reveal that the increase of ammonia flux under aerobic conditions correlates with nitrification. Due to the metabolic mechanisms of the microorganisms in activated sludge floc, which varies from one treatment plant to another, the oxygen flux inside the sludge floc changes accordingly.

Ammonia↗

PubMedDate not supplied

Oxidation-reduction potential changes in aeration tanks and microprofiles of activated sludge floc in medium- and low-strength wastewaters.

Real-time control of aeration tank operation is key to high-efficiency pollutant removal and energy savings. One of the aims of this study was to examine the potential for using redox potential (oxidation-reduction potential [ORP]) to indicate wastewater quality online in aeration tanks treating medium (chemical oxygen demand [COD] of 70 to 150 mg/L) and low (COD of 15 to 30 mg/L) pollutant-concentration wastewaters. The field-scale data provide a good relationship between ORP values and nutrient removal along the length of the aeration tanks. The ORP values increased dramatically as organic matter was removed along the aeration tanks, indicating the improvement of the bulk liquor redox status. Dissolved oxygen higher than 1.0 mg/L was necessary for good biodegradation and improvement of the liquid redox status. Nitrification occurred at higher ORP values (380 to 420 mV) than was the case for organic substrate oxidation (250 to 300 mV). The microprofiles obtained from microelectrode measurements substantiate the heterogeneity of the microbial processes inside activated sludge flocs. Because of microbial oxygen utilization, the aerobic region in the activated sludge floc was limited to the top layer (0.1 to 0.2 mm) of the activated sludge aggregate present in medium-strength wastewater, with an anoxic zone dominating inside the flocs. When dissolved oxygen in the bulk water was higher than 4.0 mg/L, the anoxic zone inside the floc disappeared. At low wastewater pollutant concentrations, the ORP and dissolved oxygen inside the activated sludge aggregates were higher than those from medium-strength wastewater. The prospect of using ORP as an online control approach for aeration tank operation and the potential reasons for activated sludge floc size varying with pollutant strengths are also discussed.

Air Movements↗