PubMed Health⌕ Search

Biomedical subjects

Bengt Kasemo

Publications and source records attributed to Bengt Kasemo.

At least 19 recordsLinked to original sources
PubMed2006

Signaling between cells attached to a surface.

We present a kinetic model allowing one to classify likely scenarios of protein-mediated communication between attached cells of two distinct types. In our treatment, messenger proteins, synthesized in type-1 cells, are considered to penetrate the external membrane of these cells, diffuse in the extracellular medium, associate with the receptors in the external membrane of cells of both types, and induce intracellular signal transduction cascades, influencing the development of cells. Protein degradation inside and outside cells is taken into account as well.

Animals↗
PubMed2006

Fabrication of hydroxyapatite ultra-thin layer on gold surface and its application for quartz crystal microbalance technique.

We present a method for coating gold quartz crystal microbalance with dissipation (QCM-D) sensor with ultra-thin layer of hydroxyapatite nanocrystals evenly covering and tightly bound to the surface. The hydroxyapatite layer shows a plate-like morphology and less than 20 nm in thickness. The hydroxyapatite sensor operated in liquid with high stability and sensitivity. The in-situ adsorption mechanism and conformational change of fibrinogen on gold, titanium and hydroxyapatite surfaces were investigated by QCM-D technique and Fourier-transform infrared spectroscopy. The change of secondary structures of fibrinogen adsorbed on the surfaces depended on the adsorbed amounts of protein. The secondary structure of fibrinogen adsorbed on the surfaces changes with increasing coverage. This is explained by repulsion among fibrinogens, affecting water structure and thus the strength of fibrinogen interactions on the surface. The study indicates that the hydroxyapatite sensor is applicable for qualitative and conformational analysis of protein adsorption.

Adsorption↗
PubMed2006

Adsorption and spontaneous rupture of vesicles composed of two types of lipids.

To analyze the adsorption of single vesicles composed of two types of lipids (e.g., zwitterionic and positively charged lipids or zwitterionic and negatively charged lipids), we propose a statistical model taking into account lipid-surface interactions, lipid-lipid lateral interactions, and vesicle bending energy. Our treatment specifies how these parameters govern vesicle adsorption, shows how the radius of the vesicle-surface contact area may depend on the vesicle composition, and clarifies the conditions for vesicle rupture.

Adsorption↗
PubMed2006

Plasmonic properties of supported Pt and Pd nanostructures.

The plasmonic properties of nanodisk arrays of Pt, Pd, and, for comparison, Ag are studied over a large size and spectral range and analyzed theoretically by an electrostatic model. Pt and Pd nanodisks exhibit broad localized surface plasmons with a higher sensitivity of the plasmon to the disk aspect ratio compared to Ag. Extinction cross-sections are generally about 50% smaller for Pt and Pd. The spectral plasmon positions, line-widths, and extinction cross-sections are well reproduced by the model.

Computer Simulation↗
PubMed2005

Simulation of proliferation of neural stem cells on a surface with emphasis on spatial constraints on cell division.

We present Monte Carlo lattice simulations of proliferation of cells on a surface in the situation when the cell-cell adhesion is relatively strong and the cells may form islands and/or flattened hemispheres. The model parameters were chosen to mimic proliferation of adult rat neural stem cells (or, more specifically, adult hippocampal progenitor cells) deposited on polyornithine and laminin coated polystyrene. The results obtained show that the spatial constraints on cell division may result in slowdown of the exponential growth. Depending on the rules used for cell division, this effect may be either nearly negligible or appreciable. In the latter case, the scale of the deviations from the exponential growth is comparable with that observed in our experiments. In the simulations, the slowdown of the growth starts however somewhat earlier and occurs in a less abrupt manner. This seems to indicate that the spatial constraints on division of cells are not the main factor behind the experimentally observed termination of the growth.

Animals↗
PubMed2005

A dual-frequency QCM-D setup operating at elevated oscillation amplitudes.

An often raised, but rarely addressed, question with respect to applications of the quartz crystal microbalance technique is whether the shear oscillation of the sensor surface influences the adsorption kinetics or binding events being studied. Motivated by this uncertainty, as well as by the possibility of using elevated amplitudes to influence and steer specific biomolecular interactions, we have further developed the quartz crystal microbalance with dissipation monitoring (QCM-D) technique to operate in dual-frequency mode. One mode (one harmonic) is utilized for continuous excitation of the QCM-D sensor at resonance, at variable driving amplitudes, while the other mode (another harmonic) is used for combined frequency and energy dissipation (damping) measurements. To evaluate this experimental approach, we investigated the following: (i) the well-established process by which intact lipid vesicles adsorb and decompose into a planar supported lipid bilayer on SiO2, recently shown to be very sensitive to external perturbations, and (ii) specific streptavidin binding to biotin-modified surfaces. In the former case, we observed a clear influence of elevated oscillation amplitudes on the bilayer formation kinetics, while in the latter case, no influence was observed for protein monomers. However, binding was inhibited when the biotin-binding protein was coupled to colloidal particles (o.d. approximately 200 nm).

Journal Article↗
PubMed2005

In situ reactivity and FTIR study of the wet and dry photooxidation of propane on anatase TiO2.

The photocatalytic oxidation (PCO) of trace amounts of propane (500 ppm) on nanocrystalline anatase TiO2 has been investigated in situ as a function of temperature (T = 318-473 K), humidity (C(H2O) = 0-4%), and time by means of mass spectrometry and diffuse reflectance Fourier transform infrared spectroscopy (DRIFT). Propane adsorbs associatively on TiO2 at 318 K in dry air, while at 473 K small amounts of thermal dissociation products appear on the surface. In agreement with previous studies, propane is found primarily to be converted to acetone by reactions with photogenerated oxygen radicals. Various successive reaction paths exist, where the branching depends on the temperature and hydroxylation state of the surface. Under dry conditions at 318 K, acetone oxidation is initially kinetically hindered, while, above 400 K, acetone readily decomposes. The thermally assisted reaction channel leads to detrimental bonding of surface species and inhibition of the catalytic activity. It is manifested by a coloration of the sample and suggested to be coupled to surface reduction. Under humidified conditions, there is an optimum of the PCO in C(H2O) and T space, which is estimated to correspond to an equilibrium coverage of one monolayer of H2O (or bilayer). The latter reaction condition also corresponds to sustained high propane conversion and is characterized by rapid establishment of steady state rates. The optimum PCO is discussed in terms of a balance between (i) sustaining enough of a photoactive water monolayer to avoid detrimental bonding of surface species, (ii) allowing reactants to adsorb and access bulk TiO2 photoexcitations, and at the same time (iii) maximizing the thermally assisted decomposition of intermediates.

Journal Article↗
PubMed2005

Confined plasmons in nanofabricated single silver particle pairs: experimental observations of strong interparticle interactions.

We report on the optical properties of single isolated silver nanodisks and pairs of disks fabricated by electron beam lithography. By systematically varying the disk size and surface separation and recording elastic scattering spectra in different polarization configurations, we found evidence for extremely strong interparticle interactions. The dipolar surface plasmon resonance for polarization parallel to the dimer axis exhibited a red shift as the interdimer separation was decreased; as expected from previous work, an extremely strong shift was observed. The scattering spectra of single particles and pairs separated by more than one particle radius can be well described by the coupled dipole approximation (CDA), where the particles are approximated as point dipoles using a modified dipole polarizability for oblate spheroids. For smaller particle separations (d < 20 nm), the simple dipole model severely underestimates the particle interaction, indicating the importance of multipolar fields and finite-size effects. The discrete dipole approximation (DDA), which is a finite-element method, describes the experimental results well even at d < 20 nm, including particles that have metallic bridges.

Journal Article↗
PubMed2005

Controlling plasmon line shapes through diffractive coupling in linear arrays of cylindrical nanoparticles fabricated by electron beam lithography.

The effect of diffractive coupling on the collective plasmon line shape of linear arrays of Ag nanoparticles fabricated by electron beam lithography has been investigated using Rayleigh scattering spectroscopy. The array spectra exhibit an intricate multi-peak structure, including a narrow mode that gains strength for interparticle distances that are close to the single particle resonance wavelength. A version of the discrete dipole approximation method provides an excellent qualitative description of the observed behavior.

Electrons↗
PubMed2004

Simultaneous surface plasmon resonance and quartz crystal microbalance with dissipation monitoring measurements of biomolecular adsorption events involving structural transformations and variations in coupled water.

Simultaneous quartz crystal microbalance with dissipation monitoring (QCM-D) and surface plasmon resonance (SPR) measurements are used to analyze the surface kinetics of two biomacromolecular systems, one lipid and one protein based, undergoing surface-induced conformational changes. First we establish a theoretical platform, which allows quantitative analysis of the combined SPR and QCM-D data. With this theoretical base, new information can be extracted, not obtainable with either technique alone. As an example we demonstrate how time-resolved measurements with these two techniques in combination--yielding three independent measured quantities--add new information about (i) kinetics, i.e. number of adsorbed molecules per unit area versus time, and (ii) temporal variation in the mass fraction of coupled water versus coverage. In particular, it is demonstrated for the first time, how the kinetics of the process during which adsorbed vesicles are spontaneously transformed into a supported phospholipid bilayer (SPB) on SiO(2) can be quantitatively separated into its two dominating states: adsorbed vesicles and supported planar bilayer patches. In addition, the relevance of dynamically coupled water for interpretation and modeling of the QCM-D response during bilayer formation is discussed and further illustrated with a second model system: streptavidin adsorption on a biotin-modified SPB. A very strong coverage dependence in the number of water molecules per protein sensed by the QCM is demonstrated, with strong implications for the use of QCM as a tool for quantitative determination of protein mass uptake kinetics.

Adsorption↗
PubMed2004

A minimal generic model of bacteria-induced intracellular Ca2+ oscillations in epithelial cells.

The toxin alpha-hemolysin expressed by uropathogenic Escherichia coli bacteria was recently shown as the first pathophysiologically relevant protein to induce oscillations of the intracellular Ca(2+) concentration in target cells. Here, we propose a generic three-variable kinetic model describing the Ca(2+) oscillations induced in single rat renal epithelial cells by this toxin. Specifically, we take into account the interplay between 1), the cytosolic Ca(2+) concentration; 2), IP(3)-sensitive Ca(2+) channels located in the membrane separating the cytosol and endoplasmic reticulum; and 3), toxin-related activation of production of IP(3) by phospholipase C. With these ingredients, the predicted response of cells exposed to the toxin is in good agreement with the results of experiments.

Animals↗
PubMed2004

Utilizing adsorbed proteoliposomes trapped in a non-ruptured state on SiO2 for amplified detection of membrane proteins.

The quartz crystal microbalance with dissipation (QCM-D) technique was used to monitor the formation of supported phospholipid bilayers (SPBs) on SiO2 using proteoliposomes with reconstituted proton translocating nicotinamide nucleotide transhydrogenase (TH). Exposure of the surface to such proteoliposomes creates a lipid film composed of a mixture of proteolipid bilayers and adsorbed non-ruptured proteoliposomes, where the fraction of the latter is reduced if the TH-liposomes are pretreated with trypsin to remove the water soluble domains of TH [Langmuir 19 (2003) 842]. In the present work, the latter study is complemented by investigating the influence of trypsin treatment of the mixed adlayer (proteolipid bilayer + non-ruptured proteoliposomes) after adsorption on the surface. This demonstrates how trypsin-cleavage induced rupture of adsorbed TH-liposomes can be utilized to detect the presence of less than 0.04 pmol/cm2 of immobilized TH.

Adsorption↗
PubMed2003

Model porous surfaces for systematic studies of material-cell interactions.

A model system for studying cell-surface interactions, based on microfabricated cell culture substrates, has been developed and is described here. Porous surfaces consisting of interconnecting channels with openings of subcellular dimensions are generated on flat, single crystal, silicon substrates. Channel size (width, depth), distribution, and surface coating can be varied independently and used for systematic investigation of how topographical, chemical, and elastic surface properties influence cell or tissue biological responses. Model porous surfaces have been produced by using two different microfabrication methods. Submicron-sized channels with very high depth-to-width aspect ratios (up to 30) have been made by using electron beam lithography and anisotropic reactive ion etching into single-crystal silicon. Another method uses thick-resist photolithography, which can be used to produce channels wider than 1 microm and with depth-to-width aspect ratios below 20 in an epoxy polymer. Preliminary cell culture tests show that fibroblasts bridge 0.8- to 1.8-microm-wide channels with very few exceptions (i.e., a continuous space below the cell-surface interface is created). It has also been shown that variation of channel periodicity significantly affects fibroblast morphology and attachment density. With this model system, it is possible to load the channels with bioactive substances intended to interact with cells at or near the surface in a time-dependent manner.

Biocompatible Materials↗
PubMed2003

Water condensation kinetics on a hydrophobic surface.

Employing thermal desorption spectroscopy, we show that the effective probability of water condensation at low water vapor pressure on an octane film is much below unity at 100-120 K. This unusual finding is related to a small binding energy of H2O monomers on octane (approximately equal to 0.08 eV), requiring the formation of critical water clusters for condensation to occur. This results in strong temperature and impingement-rate dependencies of the water condensation rate and a nonlinear uptake as a function of dose time. All these features are rationalized quantitatively by a kinetic model of water condensation.

Journal Article↗
PubMed2003

Cell adhesion on supported lipid bilayers.

The cell and protein repellent properties of supported phospholipid bilayer (SPB) membranes were investigated. The SPBs were prepared by vesicle adsorption on SiO(2) surfaces. The vesicles of phosphatidylcholine fuse and rupture, and form a supported bilayer covering the surface. We carried out cell culture experiments on several surfaces, including SPBs, using two types of epithelial cells to address the cell adhesional properties. The Quartz Crystal Microbalance Dissipation (QCM-D) technique was used to monitor the SPB formation and subsequent protein adsorption. Neither cell type adhered or proliferated on SiO(2) surfaces coated with SPBs, whereas both cell types adhered and proliferated on the three control surfaces of SiO(2), tissue culture glass, and TiO(2). The QCM-D measurements showed that about two orders of magnitude less mass adsorbed on a SPB surface compared to a TiO(2) surface, from serum-containing media (10% fetal bovine serum). The reduced adsorption on the SPB is a likely explanation for the nondetectable epithelial cell adhesion on the SPB surface. Biomembranes are therefore attractive candidate systems to achieve alternating cell-resistant and cell-interacting regions on surfaces, by including specific cell-binding proteins in the latter regions.

Adsorption↗
PubMed2003

Response of rat osteoblast-like cells to microstructured model surfaces in vitro.

The role of surface microtopography in combination with different surface wettability for rat calvaria cell differentiation was examined. Mineralization and alkaline phosphatase (ALP) activity of rat calvaria cells on flat polydimethylsiloxane (PDMS) or PDMS contained pyramids which were either hydrophilic or hydrophobic were compared. ALP expressing cells were more frequent on hydrophilic PDMS contained pyramids. ALP activity, peaked at day 9, was highest for hydrophilic pyramids followed by hydrophobic pyramids and flat hydrophilic PDMS surfaces. A similar pattern was obtained with respect to mineralized nodules. These observations showed that micro-sized surface features promote differentiation of rat calvaria cells. Further, hydrophilic surfaces are more prone to stimulate differentiation in comparison with hydrophobic surfaces. The results suggest that both material surface chemistry and topography affect osteoblast differentiation.

Alkaline Phosphatase↗
PubMed2003

Nanoscale features influence epithelial cell morphology and cytokine production.

Available, easy and fast fabrication methods of nanostructured surfaces, and the knowledge that cells in vivo interacts with nanometer-sized structures/objects, led us to study the impact of nanotopography on cell morphology and cytokine production. Uroepithelial cells were seeded on three different substrate types: two with defined nanometer topographies and a flat control, all three having identical surface chemistry. The nanostructured substrates contained hemispherical pillars or step edges, the latter in the form of parallel grooves and ridges. Qualitative and quantitative analysis of cell morphology and cytokine production were studied. Both quantities were significantly different between cells cultured on hemispherically structured surfaces compared to flat control surfaces. Cells cultured on hemispherically structured surfaces showed a decrease in IL-6 and IL-8 production and were less spread, less round and more stellate (larger dispersion). Only cell morphology differed between cells cultured on grooved surfaces and flat control surfaces. These findings suggest that epithelial cell morphology and cytokine production are dependent on the underlying nanotopography.

Biocompatible Materials↗