Biomedical subjects

Bernd Reitemeier

Publications and source records attributed to Bernd Reitemeier.

7 recordsLinked to original sources

PubMed2006

A process for making cutaneous radiation applicators based on digital data.

An optical modeling process for facial regions and other body surfaces has been developed. The body part in question is digitized using optical 3-D metrology to obtain a comprehensive dataset. The data is then prepared for further use by smoothing the point clusters. The radiophysically significant position of the radioactive material, e. g., seeds, aluminum tubes, etc., can be accurately determined using CAD modeling. Subsequently, a rapid prototyping process (fused deposition modeling [FDM]) is used to implement the CAD model directly in order to create a radiation applicator that can be used in practice. Biologically compatible polycarbonate can be used for this purpose.

Brachytherapy↗

PubMed2004

Optical modeling of extraoral defects.

In order to reduce the stress caused to patients by conventional methods of modeling using computed tomography (CT) or magnetic resonance imaging (MRI), an optical modeling process has been developed for extraoral defects and body areas. The selected body part is digitized using optical 3-coordinate measuring technology, providing an extensive data record. This is adapted for further use by equalizing the point clouds to obtain a Computer Aided Design (CAD) model, which is converted to a physical model by means of a stereolithographic process. With this technology, the patient's physical and psychological stress may be reduced. This article describes a technique for optical modeling of an ocular prosthesis.

Computer-Aided Design↗

PubMed2003

Dimensional changes of one-piece frameworks cast from titanium, base metal, or noble metal alloys and supported on telescopic crowns.

STATEMENT OF PROBLEM: The dimensional accuracy of 1-piece frameworks cast from commercially pure titanium and used to accommodate supporting telescopic crowns has not been demonstrated. PURPOSE: To compare dimensional changes incurred in frameworks cast from commercially pure titanium, a cobalt-chromium alloy, and a noble metal (gold) alloy. MATERIAL AND METHODS: This study was based on 2 different models, both prepared to receive telescopic crowns: 1 with 4 dies, designed to measure dimensional changes of the castings in the horizontal plane; and another with 2 dies, designed to measure dimensional changes in the vertical plane. As variables for the 2-die models, the palatal shape (16- and 20-mm radius) as well as the palatal depth (20-mm radius with the smallest palatal depth of 8 mm, 16-mm radius with flat palate and palatal depth of 10 mm, 16-mm radius with greatest palatal depth of 16 mm) were studied. Ten specimens each were fabricated from a commercially pure titanium, a cobalt-chromium alloy, and a gold alloy. All castings were fabricated under standardized conditions. All measurements were taken with a computer-controlled measuring microscope at the margins of the simulated telescopic crowns; these served to calculate the ideal midpoint from which the distances between the telescopic crowns were measured. The positional relation of the telescopic crowns was determined in horizontal and vertical directions. The measurements of the cast models were compared with measurements of the original model. The distances between the dies and the angles of the chosen telescopic crowns were calculated in fractions of millimeters and the angles were measured in degrees. The Kruskal-Wallis test and the Mann-Whitney U test were used for statistical analysis. The level of significance was alpha=5%. RESULTS: With the following exceptions, none of the 3 alloy types showed significantly different results. With the 4-die model, all 3 alloys showed significant variations from the original model for chosen lengths (P=.001). For those lengths, the dimensional accuracy of the noble metal alloy was approximately 99.9% of the length of the original; for the 2 other alloys, an average value of 99.4% was determined. With the 2-die models the calculated angle was significantly different from the original model for all alloys (P=.001 or.000), independent from the palatal vault and depth. Significant differences from the original model were also found for the distance between the 2 telescopic crowns with all alloys for the 2-die model with a 16-mm depth palatal vault and a 16-mm radius (P=.001,.006, or.009). CONCLUSIONS: Within the limitations of this study, the significant different dimensional changes both for the 4-die models and the 2-die models did not depend on the type of alloy. The 2-die models demonstrated significant dimensional changes resulting from the palatal geometry of the corresponding test models; the 4-die models demonstrated a tendency to contract toward the geometric center.

Chromium Alloys↗

PubMed2002

Effect of posterior crown margin placement on gingival health.

STATEMENT OF PROBLEM: The clinical impact of posterior crown margin placement on gingival health has not been thoroughly quantified. PURPOSE: This study evaluated the effect of posterior crown margin placement with multivariate analysis. MATERIAL AND METHODS: Ten general dentists reviewed 240 patients with 480 metal-ceramic crowns in a prospective clinical trial. The alloy was randomly selected from 2 high gold, 1 low gold, and 1 palladium alloy. Variables were the alloy used, oral hygiene index score before treatment, location of crown margins at baseline, and plaque index and sulcus bleeding index scores recorded for restored and control teeth after 1 year. The effect of crown margin placement on sulcular bleeding and plaque accumulation was analyzed with regression models (P<.05). RESULTS: The probability of plaque at 1 year increased with increasing oral hygiene index score before treatment. The lingual surfaces demonstrated the highest probability of plaque. The risk of bleeding at intrasulcular posterior crown margins was approximately twice that at supragingival margins. Poor oral hygiene before treatment and plaque also were associated with sulcular bleeding. Facial sites exhibited a lower probability of sulcular bleeding than lingual surfaces. Type of alloy did not influence sulcular bleeding. CONCLUSION: In this study, placement of crown margins was one of several parameters that affected gingival health.

Adult↗

PubMed2002

Evaluation of a device for attenuation of electron release from dental restorations in a therapeutic radiation field.

STATEMENT OF PROBLEM: For some patients, radiation treatment is a part of tumor therapy in the head and neck area before and/or after surgery. The oral cavity and teeth are thereby frequently exposed to high doses of radiation. In this situation, electronic backscatter from dental materials may damage the surrounding soft tissue. PURPOSE: This study determined the degree of absorption and the backscatter effect of therapeutic radiation used in the presence of 4 different dental materials. The efficacy of a protective stent also was investigated. MATERIAL AND METHODS: The influence of 4 dental materials (a high-gold alloy, pure titanium, amalgam, and a synthetic material) on radiation dose distribution was tested on 2 test models that simulated the presence of teeth. An alanine dosimeter was used to make measurements with and without the presence of a protective stent. To verify the results, one of the test models was compared to a computer simulation. RESULTS: Backscatter effects on the surface of dental materials caused an increase of up to 170% of the radiation dose measured without the materials. The rate of overdose increased with the atomic number of the dental material. The extent of the backscatter effect was a maximum of 4 mm. CONCLUSION: The considerable overdose of 170% found in this study suggests that soft tissue surrounding dental restorations should be protected from radiation. The backscatter results indicate that soft tissue could be effectively shielded with a 3-mm synthetic stent.

Absorption↗

PubMed2002

A pilot study of three methods for the reduction of bacterial contamination of dental unit water systems in routine use.

Three different methods for minimizing the bacterial contamination of the water system in a SIRONA C2 type dental unit were investigated sequentially. Without any decontamination method, water from the hand piece, air-water-jet and mouthwash were continuously contaminated by 10(3) to 10(5) colony forming units (cfu) of aerobic mesophilic bacteria per milliliter. A reduction to below 100 cfu/ml was achieved by continuous adding of a chemical microbicide based on hydrogen peroxide and silver ions. However, this was only possible after rinsing the system thoroughly for at least two minutes after interruptions of the treatment. Long-lasting low counts of below 100/ml were obtained by means of an in-line bacteria filter, in connection with the provision of a thermo-chemical or thermal decontamination of the water pipes and hand pieces after the filter. The electrolyte release of chlorine from the dental unit tap water by anodic oxidation without addition of any chemical disinfectant also resulted in continuously low colony numbers of the water. In this case, regular decontamination of the end parts of the pipes and hand pieces was not necessary.

Bacteria↗

PubMedDate not supplied

Metal-ceramic failure in noble metal crowns: 7-year results of a prospective clinical trial in private practices.

PURPOSE: The aim of this study was to evaluate the clinical performance of metal-ceramic crowns placed in 10 private practices. MATERIALS AND METHODS: In this prospective clinical trial, 95 patients were provided with 190 noble-metal metal-ceramic single crowns. RESULTS: The 7-year survival rates of the crowns were 95.5% (target event: any removal), 99.5% (target event: removal because of defective veneer), and 92.4% (target event: metal-ceramic complication of any kind). No significant explanatory variables for metal-ceramic complications could be detected by bivariate and multivariate testing. The consequences resulting from metal-ceramic defects were of minor clinical significance in most cases. CONCLUSION: The findings support previous claims that metal-ceramic restorations perform very well clinically, including in practices outside academic environments.

Adult↗