Biomedical subjects

Binyao Li

Publications and source records attributed to Binyao Li.

5 recordsLinked to original sources

PubMed2006

Morphologies in solvent-annealed thin films of symmetric diblock copolymer.

We have systematically studied the thin film morphologies of symmetric poly(styrene)-block-poly(methyl methacrylate) (PS-b-PMMA) diblock copolymer after annealing to solvents with varying selectivity. Upon neutral solvent vapor annealing, terraced morphology is observed without any lateral structures on the surfaces. When using PS-selective solvent annealing, the film exhibits macroscopically flat with a disordered micellar structure. While PMMA-selective solvent annealing leads to the dewetting of the film with fractal-like holes, with highly ordered nanoscale depressions in the region of undewetted films. In addition, when decreasing the swelling degree of the film in the case of PMMA-selective solvent annealing, hills and valleys are observed with the coexistence of highly ordered nanoscale spheres and stripes on the surface, in contrast to the case of higher swelling degree. The differences are explained qualitatively on the basis of polymer-solvent interaction parameters of the different components.

Journal Article↗

PubMed2005

Polymer surfaces with reversibly switchable ordered morphology.

Honeycomb macroporous films fabricated by the "breath figures" method were composed of poly2-vinylpyridine (P2VP) distributed in the holes of polystyrene (PS). The porous films exhibited reversible behavior responding to water and different solvent vapors. When the porous film was treated with water, the honeycomb pattern would change to the hexagonal islandlike pattern. Once heated to remove the water, the honeycomb pattern emerged again. When the porous film was exposed to different solvent vapors, the same reversible process appeared. Carbon disulfide (CS(2)), toluene (TOL), and tetrahydrofuran (THF) solvent vapors induced the honeycomb pattern into the ordered islandlike pattern, and ethanol, chloroform, methyl ethyl ketone (MEK), and dimethylformamide (DMF) solvent vapors made the islandlike pattern come back to the honeycomb pattern. The hygroscopic property of P2VP and the polymer-solvent interaction are the driving force for the reversibly switchable morphology. The appropriate control of the hole depth is very crucial in determining the reversible changes.

Journal Article↗

PubMed2005

Molecular motions of different scales at thin polystyrene film surface by lateral force microscopy.

Lateral force microscopy (LFM) was used to probe the molecular motions at thin polystyrene film surface. The effect of the applied load on the LFM measurements was investigated by presenting both the LFM results and the surface morphology after several scans over the same area. Depending on the loads, the scanning can be nonperturbative (without alternating the surface morphology) or perturbative (patterning the surface). Temperature-dependent LFM measurements were conducted in order to determine the apparent transitions at the surface. Perturbative scans under high loads (e.g., 150 nN) witnessed that the apparent transitions shifted to low temperatures with an increasing scan rate, while the transitions behaved oppositely under lower loads (1, 10, and 20 nN). The heating effect is suggested to account for the behavior under high loads. According to our results from nonperturbative LFM, the apparent glass transition temperature (T(g)s) is more than 10 K lower than the bulk value. Moreover, rate-dependent LFM measurements were performed under 1 nN in order to detect the surface molecular motions. Time-temperature superposition yields a master curve exhibiting three apparent relaxation peaks. The molecular motions at the surface are discussed on the context of the coupling model.

Journal Article↗

PubMed2005

Controlling the size of nanostructures in thin films via blending of block copolymers and homopolymers.

The effects of molecular weight and concentration of poly (methyl methacrylate) (PMMA) homopolymer or symmetric short polystyrene-block-poly (methyl methacrylate) (PS-b-PMMA) diblock copolymer on the size of the nanostructures of its blends with symmetric long PS-b-PMMA diblock copolymer have been investigated by atomic force microscopy. By careful controlling of the film thickness, solvent selectivity, and annealing time, PMMA cylindrical microdomains oriented normal to the film surface were obtained in all thin films. With the addition of both low- and high-molecular-weight PMMA homopolymers, the cylindrical domain sizes increased although it was less obvious for the lower molecular weight homopolymer. In contrast to the homopolymer, adding the short chain diblock copolymer resulted in a decrease in the cylindrical domain size, which was ascribed to the reduction of the interfacial tension and increase in the stretching energy.

Journal Article↗

PubMed2004

Solvent-induced microphase separation in diblock copolymer thin films with reversibly switchable morphology.

We have studied the surface morphology of symmetric poly(styrene)-block-poly(methyl methacrylate) diblock copolymer thin films after solvent vapor treatment selective for poly(methyl methacrylate). Highly ordered nanoscale depressions or striped morphologies are obtained by varying the solvent annealing time. The resulting nanostructured films turn out to be sensitive to the surrounding medium, that is, their morphologies and surface properties can be reversibly switchable upon exposure to different block-selective solvents.

Journal Article↗