Biomedical subjects

Bradley R Ringeisen

Publications and source records attributed to Bradley R Ringeisen.

6 recordsLinked to original sources

PubMed2006

A biofilm enhanced miniature microbial fuel cell using Shewanella oneidensis DSP10 and oxygen reduction cathodes.

A miniature-microbial fuel cell (mini-MFC, chamber volume: 1.2 mL) was used to monitor biofilm development from a pure culture of Shewanella oneidensis DSP10 on graphite felt (GF) under minimal nutrient conditions. ESEM evidence of biofilm formation on GF is supported by substantial power density (per device cross-section) from the mini-MFC when using an acellular minimal media anolyte (1500 mW/m2). These experiments demonstrate that power density per volume for a biofilm flow reactor MFC should be calculated using the anode chamber volume alone (250W/m3), rather than with the full anolyte volume. Two oxygen reduction cathodes (uncoated GF or a Pt/vulcanized carbon coating on GF) were also compared to a cathode using uncoated GF and a 50mM ferricyanide catholyte solution. The Pt/C-GF (2-4% Pt by mass) electrodes with liquid cultures of DSP10 produced one order of magnitude larger power density (150W/m3) than bare graphite felt (12W/m3) in this design. These advances are some of the required modifications to enable the mini-MFC to be used in real-time, long-term environmental power generating situations.

Bioelectric Energy Sources↗

PubMed2006

High power density from a miniature microbial fuel cell using Shewanella oneidensis DSP10.

A miniature microbial fuel cell (mini-MFC) is described that demonstrates high output power per device cross-section (2.0 cm2) and volume (1.2 cm3). Shewanella oneidensis DSP10 in growth medium with lactate and buffered ferricyanide solutions were used as the anolyte and catholyte, respectively. Maximum power densities of 24 and 10 mW/m2 were measured using the true surface areas of reticulated vitreous carbon (RVC) and graphite felt (GF) electrodes without the addition of exogenous mediators in the anolyte. Current densities at maximum power were measured as 44 and 20 mA/m2 for RVC and GF, while short circuit current densities reached 32 mA/m2 for GF anodes and 100 mA/m2 for RVC. When the power density for GF was calculated using the cross sectional area of the device or the volume of the anode chamber, we found values (3 W/m2, 500 W/m3) similar to the maxima reported in the literature. The addition of electron mediators resulted in current and power increases of 30-100%. These power densities were surprisingly high considering a pure S. oneidensis culture was used. We found that the short diffusion lengths and high surface-area-to-chamber volume ratio utilized in the mini-MFC enhanced power density when compared to output from similar macroscopic MFCs.

Anthraquinones↗

PubMed2006

Jet-based methods to print living cells.

Cell printing has been popularized over the past few years as a revolutionary advance in tissue engineering has potentially enabled heterogeneous 3-D scaffolds to be built cell-by-cell. This review article summarizes the state-of-the-art cell printing techniques that utilize fluid jetting phenomena to deposit 2- and 3-D patterns of living eukaryotic cells. There are four distinct categories of jetbased approaches to printing cells. Laser guidance direct write (LG DW) was the first reported technique to print viable cells by forming patterns of embryonic-chick spinal-cord cells on a glass slide (1999). Shortly after this, modified laser-induced forward transfer techniques (LIFT) and modified ink jet printers were also used to print viable cells, followed by the most recent demonstration using an electrohydrodynamic jetting (EHDJ) method. The low cost of some of these printing technologies has spurred debate as to whether they could be used on a large scale to manufacture tissue and possibly even whole organs. This review summarizes the published results of these cell printers (cell viability, retained genotype and phenotype), and also includes a physical description of the various jetting processes with a discussion of the stresses and forces that may be encountered by cells during printing. We conclude the review by comparing and contrasting the different jet-based techniques, while providing a map for future experiments that could lead to significant advances in the field of tissue engineering.

Animals↗

PubMed2005

Proteomic analysis of formalin-fixed prostate cancer tissue.

Proteomic analysis of formalin-fixed paraffin-embedded (FFPE) tissue would enable retrospective biomarker investigations of this vast archive of pathologically characterized clinical samples that exist worldwide. These FFPE tissues are, however, refractory to proteomic investigations utilizing many state of the art methodologies largely due to the high level of covalently cross-linked proteins arising from formalin fixation. A novel tissue microdissection technique has been developed and combined with a method to extract soluble peptides directly from FFPE tissue for mass spectral analysis of prostate cancer (PCa) and benign prostate hyperplasia (BPH). Hundreds of proteins from PCa and BPH tissue were identified, including several known PCa markers such as prostate-specific antigen, prostatic acid phosphatase, and macrophage inhibitory cytokine-1. Quantitative proteomic profiling utilizing stable isotope labeling confirmed similar expression levels of prostate-specific antigen and prostatic acid phosphatase in BPH and PCa cells, whereas the expression of macrophage inhibitory cytokine-1 was found to be greater in PCa as compared with BPH cells.

Amino Acid Sequence↗

PubMed2005

Laser printing of single cells: statistical analysis, cell viability, and stress.

Methods to print patterns of mammalian cells to various substrates with high resolution offer unique possibilities to contribute to a wide range of fields including tissue engineering, cell separation, and functional genomics. This manuscript details experiments demonstrating that BioLP Biological Laser Printing, can be used to rapidly and accurately print patterns of single cells in a noncontact manner. Human osteosarcoma cells were deposited into a biopolymer matrix, and after 6 days of incubation, the printed cells are shown to be 100% viable. Printing low numbers of cells per spot by BioLP is shown to follow a Poisson distribution, indicating that the reproducibility for the number of cells per spot is therefore determined not by the variance in printed volume per drop but by random sampling statistics. Potential cell damage during the laser printing process is also investigated via immunocytochemical studies that demonstrate minimal expression of heat shock proteins by printed cells. Overall, we find that BioLP is able to print patterns of osteosarcoma cells with high viability, little to no heat or shear damage to the cells, and at the ultimate single cell resolution.

Cell Count↗

PubMedDate not supplied

Laser printing of pluripotent embryonal carcinoma cells.

A technique by which to print patterns and multilayers of scaffolding and living cells could be used in tissue engineering to fabricate tissue constructs with cells, materials, and chemical diversity at the micron scale. We describe here studies using a laser forward transfer technology to print single-layer patterns of pluripotent murine embryonal carcinoma cells. This report focuses on verifying cell viability and functionality as well as the ability to differentiate cells after laser transfer. We find that when cells are printed onto model tissue scaffolding such as a layer of hydrogel, greater than 95% of the cells survive the transfer process and remain viable. In addition, alkaline comet assays were performed on transferred cells, showing minimal single-strand DNA damage from potential ultraviolet-cell interaction. We also find that laser-transferred cells express microtubular associated protein 2 after retinoic acid stimulus and myosin heavy chain protein after dimethyl sulfoxide stimulus, indicating successful neural and muscular pathway differentiation. These studies provide a foundation so that laser printing may next be used to build heterogeneous multilayer cellular structures, enabling cell growth and differentiation in heterogeneous three-dimensional environments to be uniquely studied.

Animals↗