PubMed Health⌕ Search

Biomedical subjects

C S Hsu

Publications and source records attributed to C S Hsu.

At least 37 records · Page 2Linked to original sources
PubMed1996

[The bonding mechanisms of base metals for metal-ceramic crown microstructure analysis of bonding agent and gold bond between porcelain and base metals].

The use of base metal alloys for porcelain fused to a metal crown and bridges has increased recently because of lower price, high hardness, high tensile strength and high elastic modulus. The addition of beryllium to base metal alloys increased fluidity and improved casting fitness. Beryllium also controlled surface oxidation and bonding strength. The bonding agent and gold bonding agent also affected the bonding strength between porcelain and metal alloys. Four commercially available ceramic base alloys were studied (two alloys contained beryllium element, another two did not). The purpose of this investigation was to study the microstructure between porcelain matrix, bonding agent and alloy matrix interfaces. A scanning electron micro-probe analyzer and energy dispersive X-ray spectroscopy (EDXS) were used to study the distribution of elements (Ni, Cr, Mo, Cu, O, Si, Sn, Al) in four base alloys. The following results were obtained: 1. The thickness of the oxidized layer of Rexillium III alloy and Unitbond alloy (contained beryllium) was thinner than Unibond alloy and Wiron 88 alloy (no beryllium). 2. The thickness of the oxidized layer of alloys in air (10 minutes and 30 minutes) was thinner in Unitbond (2.45 microns and 3.80 microns) and thicker in Wiron 88 (4.39 microns and 5.96 microns). 3. The thickness of the oxidized layer occurring for a duration of ten minutes (in vaccum) showed that the Rexillium III alloy was the thinnest (1.93 microns), and Wiron 88 alloy was the thickest (2.30 microns). But in thirty minutes (vacuum), Unitbond alloy was the thinnest (3.37 microns), and Wiron 88 alloy was the thickest (5.51 microns). 4. The intensity of Cr elements was increased obviously near the interface between Unitbond alloy, Wiron 88 alloy (no beryllium) and oxidized layer, but the intensity of Ni and Mo elements was slightly increased. The intensity of Cr element was not increased markedly between Rexillium III alloy, Unitbond alloy (beryllium) and oxidized layer. 5. A white-grayish oxidized layer appeared at the metal-ceramic interfaces but the thickness of oxidized layer was not obviously different. 6. The use of bonding agent at metal-ceramic interface leads to the deposition of many Sn elements at about 40 microns range within the porcelain surface. 7. Second interaction phases at the porcelain layer appeared when gold bonding agent was used, and a 50-100 microns microleakage occurred at the metal-ceramic interface.

Dental Bonding↗
PubMed1996

[The shear bond strength of porcelain and base metal alloys for metal-ceramic crown the study of metal roughness and microstructure].

The metal-ceramic crown has become a predominant restoration in fixed prosthodontics. The base metal has the quality of lower price, high tensile strength, high elastic modulus. The base metal alloy that contain beryllium element increases fluidity and improved casting performance. Beryllium also controls surface oxidation and affects the metal ceramic bonds. Preparation of surface prior to porcelain bonding has been a subject of controversy among dental ceramists. Two ceramic base metal alloys (one alloy contains beryllium, another is not) were studied. This investigation evaluated the polishing effects of 50 microns, 100 microns aluminum oxide sandblasting, carbide bur, carborundum point and separating disk upon two base metal alloys, Rexillium III and Wiron 88. A scanning electron microscope was used to study the surface texture. The following results were obtained: 1. The most roughest surface was created with 50 microns aluminum oxide sandblasting. The carbide bur produced the least roughed surface. 2. There are specific surface texture patterns after polishing with five different grinding materials. 3. The metal surfaces treated with 50 microns and 100 microns aluminum oxide have same micro-structure pictures, but there are much more undercuts treated with 100 microns aluminum oxide. 4. The usage of carbide bur resulted in less undercuts of metal surface at two metal alloys. 5. The usage of carborundum point and disk resulted in abrasive particles that retained on the grinding metal surface at two metal alloys. 6. The surface of Wiron 88 alloy usually had wrinkle texture but not the Rexillium III alloy.

Crowns↗
PubMed1996

Recurrent epistaxis following nasotracheal intubation--a case report.

Epistaxis is one of the common complications of nasotracheal intubation. Clinical patterns of all nasal bleeding are mild and may stop spontaneously in most patients. Serious nasal bleeding requiring hospitalization are rare. Nasal bleeding occurs more frequently in children than in adults. Among adults, men have a higher incidence than women. Although numerous publications have reported the cases of initial epistaxis caused by nasotracheal intubation, recurrent epistaxis was reported rarely. We experienced a case of recurrent epistaxis occurring in the 6th, 8th, 15th and 18th day after nasotracheal intubation. Herein, we describe the clinical events and discuss the causes of epistaxis.

Adult↗
PubMed1995

[Arytenoid subluxation following endotracheal intubation--a case report].

A previously healthy 39-yr-old man was scheduled for exploratory laparotomy due to acute abdomen. There was no sign of difficult intubation. After induction of anesthesia with thiopental and succinylcholine, the trachea was easily intubated with a 7.0 mm cuffed endotracheal tube. Surgery for a ruptured appendix with 2 drainage tubes lasted for 75 min was uneventful. At the end of surgery, the endotracheal tube was removed without difficulty. On the 1st postoperative day, the patient developed stridor. The symptom persisted even after conservative treatment and removal of NG tube. On the 12th postoperative day, a telescopic videolarygoscopy revealed immobile right vocal cord with anterior and medial displacement to the right. Arytenoid cartilage was moderately edematous. A diagnosis of right arytenoid subluxation was then made. On the 17th postoperative day, a closed reduction of right arytenoid cartilage using direct laryngoscope was performed successively under general anesthesia. Eight weeks after the reduction, his voice and laryngoscopic findings were normal. There has been only 18 reports with 27 cases of this complication found in the literature. However, it is generally believed that it is not so unusual. The post-intubation syndromes, such as sore throat, dysphonia, odynophagia, difficulty in swallowing or breathing which persists beyond 5 days warrant ENT consultation. Abnormal mobility of vocal cord, edema over arytenoid area found by indirect laryngoscopy should suggest the complication. Further confirmation is then needed. Although the result of our case is good, the reduction should ideally be done within 24-48 h after the incidence to avoid unfavorable long-term sequelae.

Adult↗
PubMed1992

[The stress distribution of prefabricated screw posts. Part III: Techniques].

Some commonly used endodontic screw posts were analysed for various techniques of post insertion by photoelastic stress distribution. These endodontic dowels were installed in assumed clinical conditions. These conditions included: (1) no backing off during post installation, (2) the channelling of the post without cleaning, (3) a smaller drill was used prepare the post channel, and (4) an axis deviated contrangle was used to prepare the post channel. According to this photoelastic analysis, the techniques of post insertion may affect the stress distribution. Suggestions for post insertion are as follows: 1. The stress can be reduced by counterrotating the dowel one-fourth turn after resistance to installation has been detected. 2. The channel should be cleaned thoroughly before post insertion. 3. Because accurate post fit is important to maximize both retention and support, the screw post should be used with the matched post/reamer system; and accurate contrangle drilling should be maintained.

Humans↗
PubMed1991

The cytological diagnosis of nasopharyngeal carcinoma using a silk swab stick.

A prospective study was carried out to investigate the efficacy of exfoliative cytology for the diagnosis of nasopharyngeal carcinoma. Exfoliated nasopharyngeal cells were collected from patients with a clinical suspicion of carcinoma by scraping the nasopharyngeal mucosa with a piece of silk wrapped around one end of a wooden stick. Ninety-eight patients were investigated in this manner, and the results of cytological investigation compared with the histological findings. The sensitivity of cytological investigation was 71% and the overall accuracy was 86%. The combined use of cytology and serology as a method of screening for nasopharyngeal carcinomas is discussed.

Adolescent↗
PubMed1990

Effect of isoproterenol on the uptake of [14C]glucose into glial cells.

The effect of isoproterenol on the uptake of [14C]glucose into cultured glial cells was investigated in the present study. Isoproterenol markedly stimulated the uptake of [14C]glucose 30 min after incubation. This action was produced in a dose-dependent manner. A positive correlation between the increase of [14C]glucose uptake and the stimulation of adenylate cyclase induced by isoproterenol was obtained (r = 0.99). The effect of isoproterenol was reduced by the beta-adrenergic blockers but not by other blockers, indicating the selective action of isoproterenol. The results obtained suggest that isoproterenol stimulates the uptake of glucose into glial cells through the activation of beta-adrenoceptors which are linked to adenylate cyclase.

Animals↗
PubMed1989

[Changes in microstructure of ceramic alloys after heat and electrochemical acid treatment].

The technique of electrochemical etching was developed by Dr. Tegart for application in both research and industry in 1959. There is considerable evidence showing that in conjunction with chemical bonding, surface roughness of etched casting restorations can apparently improve the mechanical adherence between the porcelain and the metal. It is obvious that surface roughness produced by sandblasting or electrochemical etching of the metal substrate not only provides mechanical interlocking but also increases the surface area for porcelain attachment. It was observed in this study that a properly heat-treated surface was significantly rougher than a surface without appropriate treatment after electrochemical acid etching. The roughness of base metals also treated with 0.5N nitric acid appeared greater obvious than those treated with 10% sulfuric acid. The etching pattern can be evaluated by selective removal of the alloy phases present between the dendritic arms in the base metal alloy. The technique of electrochemical acid etching is limited to alloys that solidify with a multiphasic structure- that is, a base metal alloy. And there are no known noble alloys suitable for this technique in this experiment. Electrolytic etching is most conveniently evaluated under a light microscope at about 30-80 magnifications to inspect surface relief and etching patterns. It remains to be determined by further research what is the exact cause of the increased roughness and how it improves the metal for ceramic mechanical bonding.

Acid Etching, Dental↗
PubMed1988

Ageing and infection.

An increased morbidity and mortality due to infectious disease has been noted in the ageing. Two alternative explanations may account for this. Changes in the immune system and inflammatory responses with age or an increase in age-related diseases may underlie the increased susceptibility. A review of studies of healthy older individuals demonstrates changes in the immune system with ageing but minimal change in the inflammatory response. Investigations of severe infection in older nursing-home patients requiring hospitalization indicate that infection as a cause of admission and death is significantly more common in individuals who are bedridden because of serious cardiovascular or neurological disease and require urinary catheterization. The evidence indicates that underlying disease, not the senescence of host resistance, leads to severe infection in the ageing.

Adult↗
PubMed1987

Shear strength of the composite bond to etched porcelain.

The shear bond strength of composite resin to porcelain was investigated to optimize variables for bonding porcelain laminate veneers. Scanning electron microscopy was initially used to examine the surface configuration of porcelain prepared under various conditions. A factorial experiment was undertaken to determine the effects of three different bonding methods on both etched and non-etched porcelain. Composite resin was bonded to the porcelain groups using (a) unfilled resin, (b) silane, and (c) silane with dentin adhesive. The results indicated a significant difference in shear bond strength for the three bonding groups, depending on the porcelain surface condition. For the unetched samples, significant differences in bond strength were obtained for all three bonding conditions. However, for the etched group, there were no differences between the silane and silane-with-dentin-adhesive groups. Porcelain etching significantly increased bond strength across all three bonding methods and was the main contributor to the obtained values.

Acid Etching, Dental↗