Biomedical subjects

D F Bain

Publications and source records attributed to D F Bain.

3 recordsLinked to original sources

PubMed1998

Evaluation of biodegradable rifampicin-bearing microsphere formulations using a stability-indicating high-performance liquid chromatographic assay.

The validation of a rapid and selective stability-indicating high-performance liquid chromatographic procedure for the determination of rifampicin (RIF) and its decomposition products in aqueous solution is described. Direct injection and column switching HPLC procedures have been compared and, owing to the increased sensitivity and precision, the latter has been applied to the study of RIF stability in the presence of isoascorbic acid at pH 7.4. The time-dependent hydrolytic decomposition of RIF to 3-formyl rifamycin SV (RSV) was found to be biexponential. Log concentration versus time plots of RIF and RSV decomposition were found to be parallel, indicating a pseudo equilibrium decomposition process. This feature allowed corrections for the amounts lost to secondary reactions to be calculated when the assay was applied to the determination of release characteristics of RIF from biodegradable poly-d, l-lactide-co-glycolide microspheres.

Antibiotics, Antitubercular↗

PubMedDate not supplied

Solvent influence on spray-dried biodegradable microspheres.

Microspheres of fixed poly(D,L-lactic acid) (PDLLA) composition--Resomer R104:R202H (30:70)--containing 20% w/w rifampicin have been spray-dried from a range of acetonic, halogenated, and solvent mixtures thereof under constant process conditions to examine the influence of solvent selection on microsphere characteristics. Solubility of the polymer composite in the studied solvents determined the kinetics of polymer deposition during drying. Viscosity studies provided an indirect index of solvent power in ascending order: acetone (ACT) < dichloromethane (DCM) < chloroform (CFM) < halothane (HAL). Accordingly, poorer acetonic solvents produced a more open, porous matrix of increased mean diameter, whereas DCM, CFM and HAL generated more coherent matrices of greater density and elevated glass transition temperature, which significantly retarded drug release. Yield generally increased in parallel with solvent strength and microsphere density consistent with the proposed generalized particle formation mechanism. Residual solvent also increased with particle density, both parameters being interrelated and dictated by the inherent affinity of the polymer composite for individual solvents. In turn, the position of glass transition temperature (Tg) and the quantity of associated polymer stress-relaxation were a direct function of amount and persistence of organic residue. The magnitude of these changes determined the relative rates and extents of microsphere ageing, as measured by drug release studies. In general, rate of drug release increased with Tg, after corrections were made for specific surface area (r2 = 0.963). Overall, solvent choice for spray-drying has a remarkable influence on microsphere characteristics and, accordingly, technological as well as toxicological considerations should be paid during selection of same.

Biodegradation, Environmental↗

PubMedDate not supplied

Modulation of rifampicin release from spray-dried microspheres using combinations of poly-(DL-lactide).

Microspheres containing 20% w/w rifampicin (RIF) with smooth morphology have been readily prepared from combinations of low, R104 (Mw, 2000) and moderate, R202H (Mw, 9000), molecular weight poly(D,L-lactide) (PDLLA) as a means to modulate drug release from either polymer when used alone. These have been characterized with respect to their drug loading, granulometry, in vitro drug release and thermal behaviour. Particle size distributions were Gaussian, whereby mean microsphere diameter was found to increase from 2.11 to 2.98 microns as the proportion of more viscous R202H increased, whilst > 95% of particles were < 10 microns, irrespective of the polymer blend used. Use of a reduced inlet temperature for spray-drying gave uncharacteristically high production yields in the range of 55.8-80.7% for the process. Encapsulation efficiencies were quantitative with the weight proportion of drug co-dissolved (p < 0.05), yielding microspheres of high and predictable RIF loading. In vitro drug release revealed a dramatic shift in release profile between 40 and 60% R104. Closer examination in this range showed the predicted pattern of increased release rate as the fraction of more hydrophilic R104 increased. However, disproportionate differences were evident between 44 and 48% R104. From the apparent temperature dependent drug release, the criticality of matrix composition was attributed to the coincidence of matrix softening with the dissolution medium temperature and consequent hydration, which, at a finite composition, resulted in a controlled auto-hydration mechanism. Dramatic dependence of release rate with dissolution methodology was accountable to the fact that drug release was considerably quicker where microspheres remained suspended and individualized with the USP paddle method as opposed to aggregated with the shaking bath methodology. In conclusion, the utility of blending racemic PDLLA to modulate drug release and the convenience of spray-drying as a technique to produce microspheres of predictable character have been demonstrated. The temperature-dependent release exhibited may have application in the site-specific delivery of drugs where local increased biochemical activity promotes drug release in response to an increased pharmacological need.

Aerosols↗