PubMed Health⌕ Search

Biomedical subjects

D Rempel

Publications and source records attributed to D Rempel.

At least 37 records · Page 2Linked to original sources
PubMed1997

The effect of keyboard keyswitch make force on applied force and finger flexor muscle activity.

The design of the force-displacement characteristics or 'feel' of keyboard keyswitches has been guided by preference and performance data; there has been very little information on how switch 'feel' alters muscle activity or applied force. This is a laboratory-based repeated measures design experiment to evaluate the effect of computer keyboard keyswitch design on applied finger force and muscle activity during a typing task. Ten experienced typists typed on three keyboards which differed in keyswitch make force (0.34, 0.47 and 1.02 N) while applied fingertip force and finger flexor electromyograms were recorded. The keyboard testing order was randomized and subjects typed on each keyboard for three trials, while data was collected for a minimum of 80 keystrokes per trial. No differences in applied fingertip force or finger flexor EMG were observed during typing on keyboards with switch make force of 0.34 or 0.47 N. However, applied fingertip force increased by approximately 40% (p < 0.05) and EMG activity increased by approximately 20% (p < 0.05) when the keyswitch make force was increased from 0.47 to 1.02 N. These results suggest that, in order to minimize the biomechanical loads to forearm tendons and muscles of keyboard users, keyswitches with a make force of 0.47 N or less should be considered over switches with a make force of 1.02 N.

Adult↗
PubMed1996

Temperature effects on vibrotactile sensitivity threshold measurements: implications for carpal tunnel screening tests.

This study examines the effect of skin temperature on fingertip vibrotactile sensitivity measurements and the resulting implications for carpal tunnel syndrome screening tests. Twenty subjects (11 men, 9 women) were tested for fingertip vibrotactile thresholds using the method of limits at four different frequencies (31.5, 125, 250, and 500 Hz) and six temperature categories (17 degrees-20 degrees C, 20 degrees-23 degrees C, 23 degrees-26 degrees C, 26 degrees-29 degrees C, 29 degrees-32 degrees C, 32 degrees-35 degrees C). Vibrotactile sensitivity thresholds increased with decreasing fingertip skin temperature. Furthermore, the relationship was a function of vibration frequency. Higher frequencies were more affected by temperature than lower frequencies, with significant effects beginning at 29 degrees C. These temperature-related effects may lead to possible false positive results in screening for carpal tunnel syndrome or other neuropathies. To minimize potential temperature-induced misclassification errors during these screening tests, fingertip skin temperature should be recorded before measurement and probably maintained above 29 degrees C during the measurement.

Adult↗
PubMed1996

Upper-limb Postures and Movements during Diamond Polishing.

Previous occupational health studies of diamond polishers have identified high rates of musculoskeletal disorders of the hands and arms in this population, specifically, ulnar neuropathy in the right elbow. These disorders may be due to the repetitive and forceful motions of the upper extremity required to manipulate the hand-held polishing tools. A video-based, biomechanical analysis of the upper extremities of polishers at several diamond-processing factories in Israel was conducted. Detailed motion measurements of the wrists, elbows, and shoulders of polishers were made while the subjects performed their usual work. During a typical workday, the basic polishing cycle, which involves a series of stereotyped hand and arm movements, is repeated more than 5,000 times. Sustained, extreme flexion of the right elbow, which is the arm holding the eyepiece, may account for the higher rates of ulnar neuropathy in this extremity.

Journal Article↗
PubMed1996

Keyboard reaction force and finger flexor electromyograms during computer keyboard work.

This study examines the relationship between forearm EMGs and keyboard reaction forces in 10 people during keyboard tasks performed at a comfortable speed. A linear fit of EMG force data for each person and finger was calculated during static fingertip loading. An average r2 of .71 was observed for forces below 50% of the maximal voluntary contraction (MVC). These regressions were used to characterize EMG data in force units during the typing task. Averaged peak reaction forces measured during typing ranged from 3.33 N (thumb) to 1.84 N (little finger), with an overall average of 2.54 N, which represents about 10% MVC and 5.4 times the key switch make force (0.47 N). Individual peak or mean finger forces obtained from EMG were greater (1.2 to 3.2 times) than force measurements; hence the range of r2 for EMG force was .10 to .46. A closer correspondence between EMG and peak force was obtained using EMG averaged across all fingers. For 5 of the participants the force computed from EMG was within +/-20% of the reaction force. For the other 5 participants forces were overestimated. For 9 participants the difference between EMG estimated force and the reaction force was less than 13% MVC. It is suggested that the difference between EMG and finger force partly results from the amount of muscle load not captured by the measured applied force.

Adult↗
PubMed1996

Musculoskeletal symptoms related to video display terminal use: an analysis of objective and subjective exposure estimates.

The occupational use of video display terminals (VDTs) has been associated with the increasing incidence of upper extremity musculoskeletal disorders, often called cumulative trauma disorders. To guide clinical and policy decisions about the prevention and treatment of these VDT related disorders, valid and economic measures of total daily VDT use and VDT related job tasks such as data entry or editing will be important. In this study of newspaper reporters and copy editors (n = 83), VDT use was measured with employee self reports and by sampling the work behaviors of a subsample of employees. Behavioral sampling estimated VDT use as a characteristic of the job as opposed to a characteristic of individual employee performance. Overall, the two techniques of measuring occupational VDT use compared favorably, with the exception that self reported hours of VDT use tended to exceed the hours of use estimated by behavioral observation for employees who were younger and those who reported greater job demands. The findings suggest that behavioral sampling is a valid technique for estimating VDT use as a job characteristic.

Adult↗
PubMed1994

Carpal tunnel syndrome among grocery store workers.

The California Department of Health Services evaluated carpal tunnel syndrome (CTS), a median nerve entrapment condition associated with forceful and repetitive wrist motion, among grocery store workers at a large California supermarket where a CTS cluster had been reported. Forceful and repetitive wrist motion was measured, in three exposure levels, through a job classification scheme based upon type of work tasks and average time per week spent performing these tasks. A medical questionnaire and measurements of median sensory nerve conduction were used to measure CTS. CTS prevalence was 23% based upon a sample of 56 participants drawn from a workforce of 69 employees. A relative risk of 8.3 (95% confidence interval 2.6-26.4) for a history of CTS-like symptoms between the high and low exposure level groups held up after adjustment for the potential confounders of age, sex, alcohol consumption, and high-risk medical history. It was concluded that the basic principles of good ergonomic design should be used to prevent or diminish the risk of musculoskeletal injury in the workplace.

Adult↗
PubMed1994

VDT-related musculoskeletal symptoms: interactions between work posture and psychosocial work factors.

Video display terminal (VDT) operators (n = 150) in the editorial department of a large metropolitan newspaper participated in a study of day-to-day musculoskeletal symptoms. Work posture related to the VDT workstation and psychosocial work factors were also investigated for their contributions to the severity of upper body pain, numbness, and stiffness using a representative subsample (n = 70). Self-report measures included Karasek's Job Content Instrument and the author-designed Work Interpersonal Relationships Inventory. Independent observations of work posture were performed using techniques similar to those reported by Sauter et al. [1991]. Pain during the last week was reported by 59% (n = 88) of the respondents, and 28% (n = 42) were categorized by symptom criteria potentially to have musculoskeletal disorders. More hours per day of VDT use and less decision latitude on the job were significant risk factors for potential musculoskeletal CTDs. Head rotation and relative keyboard height were significantly related to more severe pain and stiffness in the shoulders, neck, and upper back. Lower levels of co-worker support were associated with more severe hand and arm numbness. For both the region of the shoulders, neck, and upper back and the hand and arm region, however, the contributions of relative keyboard and seat back heights to symptom severity were modified by psychological workload, decision latitude, and employee relationship with the supervisor. Alternative explanations for these findings are discussed.

Adult↗
PubMed1994

A method of measuring fingertip loading during keyboard use.

A single keycap on a standard alphanumeric computer keyboard was instrumented with a piezoelectric load cell and the fingertip motion was recorded with a high-speed video motion analysis system. Contact force histories between the fingertip and the keycap were recorded while four subjects typed a standard text for five minutes. Each keystroke force history is characterized by three distinct phases: (I) keyswitch compression, (II) finger impact and (III) fingertip pulp compression and release. Each keystroke force history contained two relative maxima, one in phase II and one in phase III. The subject mean peak forces ranged from 1.6 to 5.3 N and the subject mean peak fingertip velocities ranged from 0.3 to 0.7 m/s. Motion analyses and force measurements suggest a ballistic model of finger motion during typing.

Computer Terminals↗
PubMed1994

The effect of wearing a flexible wrist splint on carpal tunnel pressure during repetitive hand activity.

We investigated how repetitive hand activity normally affects carpal tunnel pressure and whether a flexible wrist splint can influence this effect. Nineteen healthy subjects were evaluated under four test conditions: at rest with and without a wrist splint (baseline) and while performing a repetitive task with and without a wrist splint. The task involved loading and unloading 1 lb. cans from a box at a rate of 20 cans per minute for period of 5 minutes. Carpal tunnel pressure and wrist angles were continuously monitored by means of a fluid-filled catheter inserted into the carpal canal and a two-channel electrogoniometer mounted on the dorsum of the hand and forearm. Without the splint, carpal tunnel pressure rose from a median baseline level of 8 +/- 6 mmHg to 18 +/- 13 mmHg during activity. With the splint, carpal tunnel pressure rose from a baseline of 13 +/- 5 mmHg to 21 +/- 12 mmHg during activity. Median carpal tunnel pressure during activity with the splint was no different from that without the splint. Our data indicate that the median nerve is subjected to increased pressure within the carpal tunnel during repetitive hand activity. Wearing a flexible wrist splint during activity limits the range of wrist motion but has no significant effect on carpal tunnel pressure.

Adult↗
PubMed1992

Hospital records as a data source for occupational disease surveillance: a feasibility study.

To assess the feasibility of using hospital records for occupational disease surveillance and to evaluate the quality of the industry/occupation (I/O) information available in these records, the computer file of all discharge diagnoses from a large health maintenance organization during 1985 was reviewed. The frequencies of discharge diagnoses previously listed as Sentinel Health Events (Occupational), or SHE (O), were calculated and three possible SHE(O) diagnoses--lung cancer, bladder cancer, and toxic hepatitis--were selected for further review. Outpatient charts of patients discharged for each diagnosis were abstracted with regard to I/O information and the discharged patients were interviewed by telephone to obtain a lifetime occupational history. The accuracy of the I/O information obtained from the hospital chart was compared to that obtained by patient interview by number of digits matched on standard classification codes. The frequencies of matches for occupation and industry were greater for "usual" than for "last" categories with both cancer diagnoses, but were similar for "usual" and "last" categories with toxic hepatitis. To assess the proportion of each possible SHE(O) diagnosis that was related to workplace exposures, the I/O information obtained by interview was rated in a blinded fashion by an experienced occupational medicine physician. The highest probability ratings for work-relatedness were noted for lung cancer, primarily due to asbestos exposure. The results of this study suggest that hospital records can be used to identify possible SHE(O); if adequate I/O information is available, then work-relatedness can be assessed. However, the accuracy of I/O obtained from hospital charts is relatively low. The efficient and accurate collection of I/O information from hospital records will require the use of a simple, easily coded instrument to be routinely administered on admission.

Asbestos↗
PubMed1991

Respiratory effects of exposure of shipyard workers to epoxy paints.

Epoxy resin systems have been associated with occupational asthma in several case reports, but medical publications contain little on the potential adverse respiratory effects of these chemicals in exposed worker populations. To further evaluate the association of workplace exposure to epoxy paints and respiratory dysfunction, the cross workshift changes in pulmonary function and symptoms of 32 shipyard painters exposed to epoxy paints were compared with 28 shipyard painters not exposed to epoxy paints. The prevalence of lower respiratory tract symptoms was significantly higher among painters exposed to epoxy paints compared with controls. Among exposed painters the mean cross workshift change in forced expiratory volume in one second (FEV1) (-3.4%) was greater than the decrement in the non-exposed group (-1.4%). A significant linear relation was seen between % decrement in FEV1 and hours of exposure to epoxy paints. This study suggests that epoxy resin coatings as used by shipyard painters are associated with increased lower respiratory tract symptoms and acute decrements in FEV1. Adequate respiratory protection and medical surveillance programmes should be established in workplaces where exposure to epoxy resin systems occurs.

Adult↗
PubMed1990

Occupational illness and poison control centers. Referral patterns and service needs.

In a study of occupational illness reported to a regional poison control center and to gauge the center's outreach and services, we did follow-up interviews of 301 case contacts over a 6-month period. We ascertained referral routes, reasons for contacting the poison control center, and awareness of the center's function. For 122 cases a nonphysician was the initial poison control center contact. Of the nonphysician contacts, 41 had already consulted a health care provider and been referred to the poison control center for assistance. Of the 70 persons with exposure, only 21 had been aware before their exposures that poison control center services might include occupational chemical illness consultation. Physicians and nonphysicians expressed similar reasons for contacting the poison control center, with 118 of 301 identifying the need for an exposure hazard risk assessment. These data suggest that although those contacting a poison control center because of occupational illness include a variety of cases, they have many similar service needs.

Humans↗
PubMed1989

Occupational illness: case detection by poison control surveillance.

STUDY OBJECTIVE: To evaluate the usefulness of poison control center detection in occupational illness surveillance. DESIGN: Case series of all occupationally related exposures referred for poison control center consultation over 6 months. Follow-up structured interviews were done of exposed persons and health care providers. Cases were traced under established occupational illness reporting programs. SETTING: A regional poison control center. PATIENTS: Consecutive sample of 461 symptomatic occupational exposure cases. After exclusions and losses to follow-up, interview of 301 patients and the treating physician, physician's assistant, or nurse practitioner for the 223 of the patients under direct medical care. MEASUREMENTS AND MAIN RESULTS: One hundred and fifty-five persons (61%; CI, 55% to 67%) had systemic or respiratory illness; 109 (36%; CI, 31% to 41%) had eye or skin conditions. Work practices were associated with exposures more often than technical failure; 118 persons (39%; CI, 33% to 45%) reported lack of respirators or other appropriate personal protective equipment. For 223 persons who received direct medical care, only five treating health care providers (2%; CI, 0.2% to 4%) reported occupational specialization, although occupational care was a regular practice activity for 128 of the health care providers (57%; CI, 51% to 63%). Sixty-seven cases (22%; CI, 17% to 27%) were detected by the Doctor's First Report surveillance program; 97 cases (32%; CI, 27% to 37%) comprised the maximal detection estimated for Occupational Safety and Health Administration surveillance. CONCLUSIONS: Poison control center detection provides a useful surveillance measure for occupational illness. The proportion of case detection failures by established surveillance programs suggests that the incidence of occupational illness in the United States, which is calculated from these incomplete programs, may be three to five times greater than previously estimated.

Adult↗
PubMed1989

The lead-exposed worker.

The lead standard established by the federal Occupational Safety and Health Administration in 1978 requires physicians and employers to follow very specific guidelines when treating lead-exposed workers. For example, if a worker's blood lead level is 2.90 mumol/L of whole blood or greater, the worker must be removed from work, with full pay and retention of seniority, until the blood level falls below 1.95 mumol/L. Physicians play a key role in the implementation of the lead standard; the standard specifies frequency of blood lead measurements, frequency and extent of medical monitoring, and medical removal from work. This article reviews the lead standard as it applies to physicians and makes recommendations about managing the worker with lead poisoning.

Adult↗
PubMed1988

Soybean flour asthma: detection of allergens by immunoblotting.

A 43-year-old woman developed asthma 6 years after beginning work in a food-processing plant in which soybean flour was used as a protein extender. Symptoms of sneezing, coughing, and wheezing would begin within minutes of exposure to soybean flour and resolve 2 hours after exposure ceased. Skin tests were positive to a soy extract prepared from the flour. Airway hyperreactivity was confirmed by a positive bronchial challenge to methacholine. Bronchial challenge with soybean flour produced an immediate increase in specific airway resistance from 5.0 to 22.7 L. cm of H2O/L/sec. There was no response to challenge with lactose. The patient's allergic response to soy-flour extract was further characterized by several immunologic methods. IgE binding to soy-flour protein by direct RAST was 5.98 times that of a normal control serum. The soy-flour extract was separated by dodecyl sulfate-polyacrylamide gel electrophoresis. Twenty-four protein bands were detected in the crude soy-flour extract. After immunoblotting and subsequent autoradiography, nine proteins with molecular weights ranging from 54,500 to 14,875 were found. Cross-reactivity studies with other legumes demonstrated apparent immunologic identity between a component in green pea extract and a soybean protein with a molecular weight of 17,000. The clinical significance of this cross-reactivity is not known. We conclude that in this case of occupational asthma to soybean flour, multiple allergens were involved. Immunoblotting may be useful in identifying the allergens involved in occupational asthma.

Adult↗