PubMed Health⌕ Search

Biomedical subjects

Duu-Jong Lee

Publications and source records attributed to Duu-Jong Lee.

At least 19 recordsLinked to original sources

Rapid formation of hydrogen-producing granules in an anaerobic continuous stirred tank reactor induced by acid incubation.

A novel approach to rapidly initiate granulation of hydrogen-producing sludge was developed in an anaerobic continuous stirred tank reactor at 37 degrees C. To induce microbial granulation, the acclimated culture was subject to an acid incubation for 24 h by shifting the culture pH from 5.5 to 2.0. The culture was resumed to pH 5.5 after the incubation and the reactor was operated at hydraulic retention times (HRTs) of 12, 6, 2, 1, and 0.5 h in sequence. Microbial aggregation took place immediately with the initiation of acid incubation and granules were developed at 114 h. No granule was observed in the absence of acid incubation in the control test. Changing the culture pH resulted in improvement in surface physicochemical properties of the culture favoring microbial granulation. The zeta potential increased from -11.6 to -3.5 mV, hydrophobicity in terms of contact angle improved from 31 degrees to 43 degrees and extracellular proteins/polysaccharides ratio increased from 0.2 to 0.5-0.8. Formation of granular sludge facilitated biomass retention of up to 32.2 g-VSS/L and enhanced hydrogen production. The hydrogen production rate and hydrogen yield increased with the reduction in HRT at an influent glucose concentration of 10 g/L once steady granular sludge layer was formed, achieving the respective peaks of 3.20 L/L x h and 1.81 mol-H(2)/mol-glucose at 0.5 h HRT. The experimental results suggested that acid incubation was able to initiate the rapid formation of hydrogen-producing granules by regulating the surface characteristics of microbial aggregates in a well-mixed reactor, which enhanced the hydrogen production.

Anaerobiosis↗

Degradation of phenol by aerobic granules and isolated yeast Candida tropicalis.

Aerobic granules effectively degrade phenol at high concentrations. This work cultivated aerobic granules that can degrade phenol at a constant rate of 49 mg-phenol/g x VSS/h up to 1,000 mg/L of phenol. Fluorescent staining and confocal laser scanning microscopy (CLSM) tests demonstrated that an active biomass was accumulated at the granule outer layer. A strain with maximum ability to degrade phenol and a high tolerance to phenol toxicity isolated from the granules was identified as Candida tropicalis via 18S rRNA sequencing. This strain degrades phenol at a maximum rate of 390 mg-phenol/g x VSS/h at pH 6 and 30 degrees C, whereas inhibitory effects existed at concentrations >1,000 mg/L. The Haldane kinetic model elucidates the growth and phenol biodegradation kinetics of the C. tropicalis. The fluorescence in situ hybridization (FISH) and CLSM test suggested that the Candida strain was primarily distributed throughout the surface layer of granule; hence, achieving a near constant reaction rate over a wide range of phenol concentration. The mass transfer barrier provided by granule matrix did not determine the reaction rates for the present phenol-degrading granule.

Aerobiosis↗

Ionic separation efficiency of a novel electric-field-assisted membrane module comprising an array of microchannel units.

The ionic separation efficiency of a novel membrane module comprising an array of microchannel units is analyzed. Under the Debye-Hückel approximation, we derive a semianalytical expression for the ionic separation efficiency. Analyses reveal that the effects of the size of the microchannel, the fixed charge density in the membrane layer, and the permittivity of the membrane layer on ionic separation efficiency depend strongly on the valence type of electrolyte in treated water. Under the condition of a symmetric electrolyte, the ionic separation efficiency is found to be about unity and unresponsive to variation of system parameters. If the valence of the cation is higher than that of the anion, the ionic separation efficiency is larger than unity, and decreases to unity as the size of the microchannel increases. In contrast, if the valence of the cation is lower than that of the anion, the ionic separation efficiency is smaller than unity and increases to unity as the size of the microchannel increases. Under the latter two conditions, the effects of both fixed charge density in the membrane layer and permittivity of the membrane layer on the ionic separation efficiency are found to be reversed.

Journal Article↗

Residence time distribution for electrokinetic flow through a microchannel comprising a bundle of cylinders.

The electrokinetic flow of an electrolyte solution through a microchannel that comprises a bundle of cylinders is investigated for the case of constant surface potential. The system under consideration is simulated by a unit cell model, and analytical expressions for the flow field and the corresponding residence time distribution under various conditions are derived. These results are readily applicable to the assessment of the performance of a microreactor such as that which comprises a bundle of optical fibers. Numerical simulations are conducted to investigate the influences of the key parameters, including the thickness of the double layer, the strength of the applied electric field, the magnitude of the applied pressure gradient, and the characteristic sizes of a microchannel, on the residence time distribution. We show that the following could result in a shorter residence time: thin double layer, strong applied electric field, large applied pressure gradient, and small number of cylinders. Based on the thickness of the double layer, criteria are proposed for whether the flow field can be treated as a laminar flow or as a plug flow, two basic limiting cases in reactor design.

Journal Article↗

Fluorecent staining for study of extracellular polymeric substances in membrane biofouling layers.

Membrane biofouling by microbial products adversely impacts the feasibility of adopting membrane bioreactors (MBRs) for treating wastewater. The fouling layer structure determines the pressure drop across the fouling layer. Three-dimensional distributions of nucleic acids, proteins, alpha-D-GLUCOPYRANOSE POLYSACCHARIDES, AND B-D-glucopyranose polysaccharides in the fouling layer formed on a mixed cellulose ester membrane were generated utilizing a quadruple staining protocol combined with confocal laser scanning microscopy (CLSM). For the first time, this study constructed a three-dimensional volumetric grids model representing the fouling layer structure on the basis of a series of CLSM images. Quantitative structural information about the fouling layer was extracted from the CLSM images.

Bacteria↗

Electrokinetic flow in an elliptic microchannel covered by ion-penetrable membrane.

The electrokinetic flow of an electrolyte solution in an elliptical microchannel covered by an ion-penetrable, charged membrane layer is examined theoretically. The present analysis extends previous results in that a two-dimensional problem is considered, and the system under consideration simulates the flow of a fluid, for example, in a microchannel of biological nature such as vein. The electroosmostic volumetric flow rate, the total electric current, the streaming potential, and the electroviscous effect of the system under consideration are evaluated. We show that, for a constant hydraulic diameter, the variations of these quantities as a function of the aspect ratio of a microchannel may have a local minimum or a local maximum at a medium level of ionic strength, which depends on the thickness of the membrane layer. For a constant cross-sectional area, the electroosmostic volumetric flow rate, the total electric current, and the streaming potential increase monotonically with the increase in the aspect ratio, but the reverse is true for the electroviscous effect.

Electrons↗

Leachate pretreatment for enhancing organic matter conversion in landfill bioreactor.

Direct recycling of leachate from refuse of high food waste content was shown to ineffectively stabilize the refuse. This work aims at evaluating the effects of three pretreatments of leachate on the refuse stabilization efficiency were investigated. Pretreatment of leachate using an anaerobic upflow filtration bioreactor (UFB) or a well-decomposed waste layer could reduce the COD and provide methanogens, both were beneficial to establish early methanogenesis status. Using an aerobic sequential batch reactor (SBR) to pretreat the leachate could reduce its COD to 1000 mg l(-1), but the fully developed methanogenesis phase would be built up in a later stage. The organic matters in the effluent leachate inhibited both the hydrolysis/acidogenesis and the methanogenesis steps in the refuse. With the dilution and acid neutralization effects by the recycled leachate, a favorable methanogenetic environment could be produced from the column's top, which moved downward along, and finally made the breakthrough of the column.

Anaerobiosis↗

Soluble microbial products (SMP) and soluble extracellular polymeric substances (EPS) from wastewater sludge.

Laspidou and Rittmann (Water Research 36:2711-2720, 2002) proposed that the soluble extracellular polymeric substances (EPS) are identical to soluble microbial products (SMP) in sludge liquor. In this paper, we compared the physicochemical characteristics of the SMP and soluble EPS from original and aerobically or anaerobically digested wastewater sludge. The surface charges, particle sizes, residual turbidities of polyaluminum chloride (PACl) coagulated supernatant, and chemical compositions of the SMP and soluble EPS containing suspensions were used as comparison index. Experimental results revealed that the particles in SMP and soluble EPS fractions extracted from original wastewater sludge, before and after digestion, were not identical in all physicochemical characteristics herein measured. The current test cannot support the proposal by Laspidou and Rittmann (Water Research 36:2711-2720, 2002) that SMP is identical to the soluble EPS from a wastewater sludge.

Aerobiosis↗

In situ distributions and characteristics of heavy metals in full-scale landfill layers.

The leachate from methanogenic landfill normally contains low concentrations of heavy metals. Little samples had ever been collected from the full-scale landfill piles owing to technical difficulty for well drilling. We drilled two wells in Hangzhou Tianziling landfill, 20 m and 32 m in depth each, and collected solid samples of waste age of 1-4 years from both wells. The total amounts, the sequentially extracted amounts, and the chemical binding forms of heavy metals of the samples collected at different depths were measured. With the correlation between leachate production amount and the yearly rainfall amount, the leached ratio of the heavy metals were estimated only 0.13%, 1.8%, 0.15%, and 0.19% of Cu, Cd, Pb, and Zn, respectively. The heavy metals amounts in the main compositions of MSW, like glass, food waste, paper, coal cinders, were measured using fresh MSW samples. Afterward, the contents of heavy metals initially landfilled were estimated. A positive correlation was noted between the measured and the estimated initial contents of heavy metals, indicating that the low migration of heavy metals in landfill layers. However, among the metals investigated, Zn has shown better mobility inside landfill layers. Acid volatile sulfide (AVS) and the simultaneously extracted metals (SEM) were measured for all collected samples with optimal reaction conditions identified to yield nearly perfect sulfide recovery as follows: 100 g wet samples, 80 mL min(-1) N(2) flow rate, reaction time of 150 min. The SEM/AVS ratios ranged 25-45, indicating that the AVS was insufficient to immobilize the SEM. Sequential extraction using six-fraction scheme revealed that the sum of exchangeable and the avid soluble fractions of heavy metals follow: Zn>Cd>Cu, Ni, Pb>Cr. The insoluble fraction of heavy metals in MSW was high, for instance, over 80% for Cr and Pb high insoluble fractions of heavy metals in the landfilled MSW and the sorption capability of the methanogenic landfill layers should be responsible to the low concentrations of heavy metals found in leachate.

Metals, Heavy↗

Enzymatic hydrolysis of polysaccharide-rich particulate organic waste.

Hydrolysis of organic particulates in rapid fermentative processes can be inhibited. The volatile fatty acids (VFA) released during fermentation reduce pH. Whether VFA or the drop in pH inhibits hydrolysis is unclear. The effects of pH and acetate on the enzymatic hydrolysis of a potato sample that contains both carbohydrate and protein were studied at fixed pH (5-9) in the presence/absence of 20 g/L of acetate. Experimental results showed that the effects of pH and acetate on the hydrolysis of carbohydrate differed from those on the hydrolysis of protein. Numerous kinetic models fitted the hydrolysis data obtained during the first 40 h of hydrolysis when inhibitory effects were insignificant. The Chen-Hashimoto model was used herein to fit the hydrolysis data obtained during 144 h of reaction. Also, the non-competitive inhibition model of three inhibitors (H(+), OH(-), total/undissociated/dissociated acetate) successfully described the inhibition of the hydrolysis of both carbohydrate and protein.

Acetates↗

Dissolved organic matter (DOM) in recycled leachate of bioreactor landfill.

Landfill leachate needs sufficient treatment before safe disposal. Bioreactor landfill technology could effectively degrade the organic matters in recirculated leachate, hence leaving a leachate stream of low biodegradability. This study characterized the dissolved organic matter (DOM) in the leachate from simulated bioreactor landfill columns with or without presence of trace oxygen. The removal efficiencies of this DOM using coagulation-sedimentation or electrolysis processes were demonstrated. Recirculated leachates were sampled from the simulated landfill columns applying conventional mode, intermittent-aeration mode, and natural aeration mode, whose DOM was fractionated into humic acids (HA), fulvic acids (FA) and hydrophilic fractions (HyI) by the XAD-8 resin combined with the cation exchange resin method. The recirculated leachate had low BOD/COD ratio, high humic substances contents, and high aromatic content. Their HA fraction comprised mainly large molecules (>10 k Da), while the FA and HyI were composed of smaller molecules (<50 k and <4 k Da, respectively). With the presence of oxygen, the TOC contents and the contents of HA, FA and HyI in leachate reduced, with FA and HyI fractions of molecular weight (MW) lower than 4 k Da more readily degraded. The organic matters left in leachates from intermittent-aeration mode and natural aeration mode were of low biodegradability. It was tested in the following sections the effects of coagulation-sedimentation process and of electrolysis process on the removal of residual DOM in recirculated leachate. Coagulation-sedimentation tests revealed that poly ferric sulphate (PFS) could remove more COD (58.1%) from leachate than polyaluminum chloride (PACl) (22.9%), particularly on the HA fraction with MW>10 k Da. Coagulation-sedimentation could not remove most of HyI in leachate. Furthermore, the corresponding BOD/COD ratio was not improved through coagulation. Electrolysis test could also effectively removed HA of MW>10 k Da. However, the biodegradability of treated effluent considerably was improved. The electrolysis could decompose high MW substances and increase biodegradability of recirculated leachate from bioreactor landfill.

Aerobiosis↗

Leaching of carbonated air pollution control residues using compliance leaching tests.

The leaching characteristics of air pollution control (APC) residues collected in Shanghai, China, were compared by performing three compliance leaching tests. These were the standard Chinese method for determining the leaching toxicity of solid waste (GB 5086.1-1997), the USEPA's Toxicity Characteristic Leaching Procedure (TCLP), and the new European shake test (EN 12457-3). In particular, behaviors of raw samples and samples that had been subjected to natural aging were compared. Both the leaching tests and natural aging substantially affected the leaching results concerning the APC residue samples. Most importantly, EN and GB tests classified the raw APC residues as hazardous, but the residues passed the TCLP test as nonhazardous. After it had been naturally aged for 720 h, however, the aged sample was classified as hazardous by the TCLP and EN tests, but as nonhazardous by the GB test. Metals that are thought to have been immobilized by carbonation were released at pH 6.3. Model calculations based on the geochemical thermodynamic equilibrium model MINTEQA2 revealed that the formation of metal carbonates did not correspond to the noted change in the leaching behaviors in the three leaching tests. Rather, the partial neutralization of alkaline ash by dissolved CO2 changing the final pH of the leachate dominated the leaching characteristics. The leaching results showed a change in leachate pH.

Acetic Acid↗

In vitro and in vivo release of gentamicin from biodegradable discs.

Osteomyelitis is an infection of the bone and successful treatment involves the removal of the affected bone and the tissue by a surgical procedure following prolonged systemic and local antibiotic therapy for 4 to 6 weeks. The current local treatment is done by poly methyl methacrylate (PMMA) beads loaded with gentamicin and PMMA, being nondegradable, is to be removed by a second surgical procedure. The current study aims to develop a biodegradable composition that gives sustained release and hence reducing the need for a second surgery. Gentamicin-loaded discs were produced by compressing microparticle-gentamicin mixture obtained by spray drying a mixture of gentamicin in a solution of a biodegradable polymer. Different copolymers of poly (DL-lactic-co-glycolic acid) (PLGA) were used to study the effect of copolymer ratio and the hydrophilic-hydrophobic nature of the polymer. Theoretical drug loading up to 25% were studied and it was observed that 10% drug loading was optimum for gentamicin to be used as solid in spray drying. The results showed that about 60% of the drug is released in about 5 to 6 days and the remaining drug is released in about 30 days in total. An in vivo study was carried on rabbit femur and the local area and systemic concentration of gentamicin was monitored. It was observed that the local area concentration of gentamicin was above minimum inhibitory concentration for more than 20 days and this was also validated by computer simulations.

Animals↗

Drag on two coaxial, nonuniformly structured flocs in a uniform flow field.

The drag on two coaxial flocs of nonuniform structure in a Newtonian fluid is evaluated for Reynolds number ranges from 0.1 to 40. A two-layer model is adopted to simulate various possible structures of a floc. The influences of the key parameters of the problem under consideration, including the separation distance between two flocs, the Reynolds number, and the ratios (inner radius/outer radius) and (permeability of outer layer/permeability of inner layer), on the drag acting on two flocs are investigated. We show that if Reynolds number is small, the drag on the leading floc is about the same as that on the rear floc. However, if Reynolds number is sufficiently large, because wakes are formed in the rear region of the leading floc, the drag on it is greater than that on the rear floc. For a fixed mean permeability, the more nonuniform the floc structure is, the more important is its influence on the drag, and the more appreciable the deviation of the drag coefficient-Reynolds number curve from a Stokes'-law-like relation.

Journal Article↗

Aging of air pollution control residues from municipal solid waste incinerator: role of water content on metal carbonation.

This work studies the effect of water content on the aging of APC residues, with a liquid to solid ratio (L/S) of 0.25 or 10, aged with or without exposure to ambient air. After the residue was mixed with water, CaSO4 and (Na,K)Al3(SO4)2(OH)6 in the raw sample yielded ettringite. When CO2 were available, this ettringite was further transformed to gypsum, calcite and possibly gibbsite. Experimental data revealed that the concentrations of Pb, Zn, Cd, Hg, and Cu fell with age, whereas that of Cr increased. Given L/S=10, excess Ca2+ ions were present in the suspension, so a precipitate of primarily calcite crystals of sizes under 5 microm formed on the air-water surface. This layer significantly reduced the rates of decline of Pb, Zn, Cd and Hg contents, and also reduced the increasing rate of Cr content in the suspension. This result follows from the mass transfer barrier of CO2 added at the air-water surface and the occurrence of subsequent chemical reactions in the suspension. An estimate of the mass transfer rate revealed that the rate-controlling step with L/S=10 was the dissolution and diffusion of CO2 in the bulk solution. However, at L/S=0.25, the rate-limiting step was the dissolution of metals from ash particles. Water content is a very important process factor, whose distribution in the sample, and the resulting competition between carbonate ion flux and heavy metal flux, govern the reaction time required during the natural aging process.

Air Pollution↗

Gentamicin-loaded discs and microspheres and their modifications: characterization and in vitro release.

Osteomyelitis is an infection of the bone, and successful treatment involves local administration for about 6 weeks. Gentamicin is a very hydrophilic drug and tends to come out into the water phase when microspheres are fabricated using solvent evaporation method. Hence, spray drying is an option, and it was observed that the release rate tends to be fast when the particle size is small and large particles cannot be prepared by spray drying. In an effort to get better encapsulation efficiency and release rate, we have worked on the possibility of compressing the microspheres into discs and modifying the porosity of the discs by using biocompatible materials like polyethylene glycol (PEG) and calcium phosphates and also on the fabrication of double-walled and composite microspheres. In the case of microspheres, two methods of fabrication both based on solvent evaporation method were employed. The two polymers used are poly-L-lactide (PLLA) and copolymers of poly-DL-lactic-co-glycolic acid (PLGA). One method is based on the spreading coefficient theory for the formation of double-walled microspheres by using single solvent, while the other is based on the property of PLLA not being soluble in ethyl acetate (EA). Characterization to check if the microspheres formed are double-walled was performed. The fabrication method where two solvents, dichloromethane (DCM) and ethyl acetate, were used gave double-walled microspheres, while the other where only dichloromethane was used gave composites. The double-walled microspheres were smaller in size compared to the composites, which were in the range of 100-600 microm. This can be attributed to the difference in the fabrication procedure. We were able to achieve better encapsulation efficiencies of more than 50% and slower release rates, which lasted for about 15 days. It was observed that size played a major role in the encapsulation efficiency and release rates. The possibility of achieving better results by studying the effect of concentration of polymer in solvent and the effect of using different polymers was investigated.

Anti-Bacterial Agents↗

Characteristics of air pollution control residues of MSW incineration plant in Shanghai.

A unique type of waste--air pollution control (APC) residues--has received increasing attention in China since the first large-scale incinerator, Shanghai Yuqiao municipal solid waste (MSW) incineration plant, was installed in the country in 2002. The APC residues of this particular plant are similar to other residues that will be produced in other incineration plants under construction in China. This work examines for the first time the benchmark contaminants of APC residues from the Yuqiao Plant, with reference to soluble salts, heavy metals and dioxins. Experimental findings reveal that the residues contained a marked amount of soluble salts, of up to 17.4-21.9% (mostly chlorides), 0.98-1.5 ngTEQ/gash of dioxins and various heavy metals. Lead is of particular concern, and requires stabilization before disposal. Heavy metal speciation schemes were implemented herein to determine the leaching characteristics. The correlation between the amounts of soluble salts or chemical speciation of the heavy metals and the leaching toxicity of these heavy metals in the residues is considered.

Air Pollutants↗

Effects of feed solutions on refuse hydrolysis and landfill leachate characteristics.

Tap water, aerobically pre-treated leachate, and anaerobically pre-treated leachate, were each fed into the top of a series of three simulated landfills columns, filled with municipal solid waste collected in Shanghai, China. Changes in leachate, including pH, total organic carbon (TOC), and volatile fatty acids (VFAs), and the produced biogas were monitored over time. The tap-water-fed columns had a low hydrolysis rate that yielded an acidic environment (pH 4.8-5.4) in the leachate that inhibited methanogenesis reaction in the refuse. When aerobically pre-treated leachate was fed into the columns, the hydrolysis rate of total organic carbon fluctuated between 200 and 400 mg d-1 and methanogenesis in the refuse column was only partly activated. The hydrolysis rate of refuse fed with anaerobically pre-treated leachate was the highest among the three solutions. The high alkaline levels of the anaerobically pre-treated leachate and its methanogenic bacteria led to an early activation of methanogenesis in the refuse columns. The VFAs contributed approximately 40-60% of TOC in tap-water-fed columns, 60-80% of TOC in the columns fed aerobically pre-treated leachate, and up to 70-90% of TOC in columns fed with anaerobically pre-treated leachate. The feed solution had considerably affected leachate characteristics, and then the build-up of the methanogenesis in the refuse column and the composition of fermentation products in the leachate. The success of a bioreactor landfill depends on whether the recycled leachate could yield a favorable methanogenic environment in the top refuse layer, or whether an appropriate pre-treatment is adopted to modify the leachate characteristics.

Bacteria, Aerobic↗