Biomedical subjects

Elise F Morgan

Publications and source records attributed to Elise F Morgan.

4 recordsLinked to original sources

PubMed2004

Postoperative rhabdomyolysis following laparoscopic gastric bypass in the morbidly obese.

HYPOTHESIS: Laparoscopic approaches for weight reduction in the morbidly obese have become common with more than 50,000 bariatric surgical procedures being performed in 2001. The objective of this article is to raise awareness among surgeons of a new complication of rhabdomyolysis from this frequent procedure. DESIGN: Case series extracted from surgical database from January 2, 2001, through December 31, 2002. PATIENTS AND METHODS: We identified 5 cases of postoperative rhabdomyolysis in morbidly obese patients who underwent laparoscopic duodenal switch procedures with parietal gastrectomy. The cause, pathogenesis, and clinical features are reviewed and discussed. RESULTS: Postoperative rhabdomyolysis developed in 5 of 353 morbidly obese patients who underwent consecutive laparoscopic duodenal switch procedures, an incidence of 1.4%. All 5 patients were male, had a mean peak serum creatine kinase level of 19 680 U/L, and reported muscle pain in either the buttock, hip, or shoulder regions during the early postoperative period. CONCLUSIONS: We hypothesized that morbidly obese patients develop critical surface and deep tissue pressures during bariatric surgery, increasing their risk for tissue injury and rhabdomyolysis. Unexplained elevations in the serum creatinine level or reports of buttock, hip, or shoulder pain in the postoperative period should raise the possibility of rhabdomyolysis and prompt clinical investigation. We recommend routine preoperative and postoperative measurements of the serum creatine kinase and serum creatinine levels to aid detection. Surgeons need to keep a low index of suspicion because early diagnosis and treatment are the cornerstones of successful management of rhabdomyolysis.

Acute Kidney Injury↗

PubMed2004

Comparison of the elastic and yield properties of human femoral trabecular and cortical bone tissue.

The ability to determine trabecular bone tissue elastic and failure properties has biological and clinical importance. To date, trabecular tissue yield strains remain unknown due to experimental difficulties, and elastic moduli studies have reported controversial results. We hypothesized that the elastic and tensile and compressive yield properties of trabecular tissue are similar to those of cortical tissue. Effective tissue modulus and yield strains were calibrated for cadaveric human femoral neck specimens taken from 11 donors, using a combination of apparent-level mechanical testing and specimen-specific, high-resolution, nonlinear finite element modeling. The trabecular tissue properties were then compared to measured elastic modulus and tensile yield strain of human femoral diaphyseal cortical bone specimens obtained from a similar cohort of 34 donors. Cortical tissue properties were obtained by statistically eliminating the effects of vascular porosity. Results indicated that mean elastic modulus was 10% lower (p<0.05) for the trabecular tissue (18.0+/-2.8 GPa) than for the cortical tissue (19.9+/-1.8 GPa), and the 0.2% offset tensile yield strain was 15% lower for the trabecular tissue (0.62+/-0.04% vs. 0.73+/-0.05%, p<0.001). The tensile-compressive yield strength asymmetry for the trabecular tissue, 0.62 on average, was similar to values reported in the literature for cortical bone. We conclude that while the elastic modulus and yield strains for trabecular tissue are just slightly lower than those of cortical tissue, because of the cumulative effect of these differences, tissue strength is about 25% greater for cortical bone.

Aged↗

PubMed2003

Trabecular bone modulus-density relationships depend on anatomic site.

One outstanding issue regarding the relationship between elastic modulus and density for trabecular bone is whether the relationship depends on anatomic site. To address this, on-axis elastic moduli and apparent densities were measured for 142 specimens of human trabecular bone from the vertebra (n=61), proximal tibia (n=31), femoral greater trochanter (n=23), and femoral neck (n=27). Specimens were obtained from 61 cadavers (mean+/-SD age=67+/-15 years). Experimental protocols were used that minimized end-artifact errors and controlled for specimen orientation. Tissue moduli were computed for a subset of 18 specimens using high-resolution linear finite element analyses and also using two previously developed theoretical relationships (Bone 25 (1999) 481; J. Elasticity 53 (1999) 125). Resultant power law regressions between modulus and density did depend on anatomic site, as determined via an analysis of covariance. The inter-site differences were among the leading coefficients (p<0.02), but not the exponents (p>0.08), which ranged 1.49-2.18. At a given density, specimens from the tibia had higher moduli than those from the vertebra (p=0.01) and femoral neck (p=0.002); those from the trochanter had higher moduli than the vertebra (p=0.02). These differences could be as large as almost 50%, and errors in predicted values of modulus increased by up to 65% when site-dependence was ignored. These results indicate that there is no universal modulus-density relationship for on-axis loading. Tissue moduli computed using methods that account for inter-site architectural variations did not differ across site (p>0.15), suggesting that the site-specificity in apparent modulus-density relationships may be attributed to differences in architecture.

Aged↗

PubMed2002

Quantitative computed tomography estimates of the mechanical properties of human vertebral trabecular bone.

The objective of this study was to report our quantitative computed tomography (QCT) density-mechanical property regressions for trabecular bone for use in biomechanical modelling of the human spine. Cylindrical specimens of human vertebral trabecular bone (from T10 to L4) were cored from 32 cadavers (mean +/- SD age = 70.1 +/- 16.8; 13 females, 19 males) and scanned using QCT. Mechanical tests were conducted using a protocol that minimized end-artifacts over the apparent density range tested (0.09-0.38 g/cm3). To account for the presence of multiple specimens per donor in this data set, donor was treated as a random effect in the regression model. Mean modulus (319 +/- 189 MPa) was higher and mean yield strain (0.78 +/- 0.06%) was lower than typical values reported previously due to minimization of the end-artifact errors. QCT density showed a strong positive correlation with modulus (n = 76) and yield stress (r2 = 0.90-0.95, n = 53, p < 0.001). There was a weak positive linear correlation with yield strain (r2 = 0.58, n = 53, p = 0.07). Prediction errors, incurred when estimating modulus or strength for specimens from a new donor, were 30-36% of the mean values of these properties. Direct QCT density-mechanical property regressions gave more precise predictions of mechanical properties than if physically measured wet apparent density was used as an intermediate variable to predict mechanical properties from QCT density. Use of these QCT density-mechanical property regressions should improve the fidelity of QCT-based biomechanical models of the human spine for whole bone and bone-implant analyses.

Adult↗