PubMed Health⌕ Search

Biomedical subjects

Elliot M Levine

Publications and source records attributed to Elliot M Levine.

8 recordsLinked to original sources
PubMed2006

Fibroblast growth factor 2 induced proliferation in osteoblasts and bone marrow stromal cells: a whole cell model.

Fibroblast growth factor 2 (FGF2) can enhance the proliferative capacity of bone and bone marrow stromal cells; however, the mechanisms behind this effect are not well described. We present a whole-cell kinetic model relating receptor-mediated binding, internalization, and processing of FGF2 to osteoblastic proliferative response. Focusing on one of the potential signaling complex stoichiometries, we utilized experimentally measured and modeled estimated rate constants to predict in vitro proliferation and distinguish between potential binding orders. We found that piecewise assemblage of a ternary signaling complex may occur in several ways depending on the local binding environment. Using experimental data of endocytosed FGF2 as a constraint, we have also shown evidence of potential multistep processes involved in heparan-sulfate proteoglycans-bound FGF2 release, internalization, and fragment formation in conjunction with the normal metabolism of the proteoglycan.

Animals↗
PubMed2004

Bioreactor-based bone tissue engineering: the influence of dynamic flow on osteoblast phenotypic expression and matrix mineralization.

An important issue in tissue engineering concerns the possibility of limited tissue ingrowth in tissue-engineered constructs because of insufficient nutrient transport. We report a dynamic flow culture system using high-aspect-ratio vessel rotating bioreactors and 3D scaffolds for culturing rat calvarial osteoblast cells. 3D scaffolds were designed by mixing lighter-than-water (density, <1g/ml) and heavier-than-water (density, >1g/ml) microspheres of 85:15 poly(lactide-co-glycolide). We quantified the rate of 3D flow through the scaffolds by using a particle-tracking system, and the results suggest that motion trajectories and, therefore, the flow velocity around and through scaffolds in rotating bioreactors can be manipulated by varying the ratio of heavier-than-water to lighter-than-water microspheres. When rat primary calvarial cells were cultured on the scaffolds in bioreactors for 7 days, the 3D dynamic flow environment affected bone cell distribution and enhanced cell phenotypic expression and mineralized matrix synthesis within tissue-engineered constructs compared with static conditions. These studies provide a foundation for exploring the effects of dynamic flow on osteoblast function and provide important insight into the design and optimization of 3D scaffolds suitable in bioreactors for in vitro tissue engineering of bone.

Alkaline Phosphatase↗
PubMed2004

Quantitative analysis of three-dimensional fluid flow in rotating bioreactors for tissue engineering.

Tissue engineering has emerged as a viable alternative to the problem of organ and tissue shortage. Our laboratory has developed matrices for bone tissue engineering based on sintered spherical particles and, using bioreactor technology, has demonstrated the ability to produce highly mineralized matrices in vitro. In this study, porous microcapsule scaffolds were developed for bone tissue engineering in the high aspect ratio vessel rotating bioreactor. The motion of individual microcapsules as well as scaffolds in the bioreactor were studied by numerical simulation and in situ imaging analysis. Results show that spherical microcapsules with density less than the surrounding fluid exhibited two motions: (1) a periodic circular orbit with tangential speed equal to the free fall speed of the particle, and (2) an inward radial migration of the circular orbit toward the center of the bioreactor vessel. Lighter-than-water scaffolds were fabricated by sintering poly(lactic-co-glycolic acid) hollow microcarriers with diameter from 500 to 860 microm into a fixed three-dimensional geometry with approximately 30% pore volume and 180 to 190 microm median pore size. Scaffolds were fabricated with aggregate densities ranging from 0.65 g/mL and 0.99 g/mL by appropriate combinations of hollow and solid microcarriers within the scaffold. Scaffold velocity in the bioreactor for the above range of densities was accurately predicted by numerical simulation and ranged from 100 mm/s to 3 mm/s. Maximum shear stress estimation due to media flow over the exterior of the scaffold ranged from 0.3 N/m(2) to 0.006 N/m(2). Internal perfusion velocity through scaffolds also was calculated and ranged from 13 mm/s to 0.2 mm/s. Estimates of maximum interior shear stress ranged from 0.03 to 0.0007 N/m(2). These analytical methods provide an excellent vehicle for the study of bone tissue synthesis in three-dimensional culture with fluid flow.

Bioreactors↗
PubMed2003

Tissue engineered bone: measurement of nutrient transport in three-dimensional matrices.

The classic paradigm for in vitro tissue engineering of bone involves the isolation and culture of donor osteoblasts or osteoprogenitor cells within three-dimensional (3D) scaffold biomaterials under conditions that support tissue growth and mineralized osteoid formation. Our studies focus on the development and utilization of new dynamic culture technologies to provide adequate nutrient flux within 3D scaffolds to support ongoing tissue formation. In this study, we have developed a basic one-dimensional (1D) model to characterize the efficiency of passive nutrient diffusion and transport flux to bone cells within 3D scaffolds under static and dynamic culture conditions. Internal fluid perfusion within modeled scaffolds increased rapidly with increasing pore volume and pore diameter to a maximum of approximately 1% of external fluid flow. In contrast, internal perfusion decreased significantly with increasing pore channel tortuosity. Calculations of associated nutrient flux indicate that static 3D culture and some inappropriately designed dynamic culture environments lead to regions of insufficient nutrient concentration to maintain cell viability, and can result in steep nutrient concentration gradients within the modeled constructs. These quantitative studies provide a basis for development of new dynamic culture methodologies to overcome the limitations of passive nutrient diffusion in 3D cell-scaffold composite systems proposed for in vitro tissue engineering of bone.

Alkaline Phosphatase↗
PubMed2003

Human osteoblast-like cells in three-dimensional culture with fluid flow.

In a previous study, we showed that the combination of appropriately designed three-dimensional (3D) microcarrier scaffolds and fluid flow through and around the scaffolds during high aspect ratio vessel (HARV) rotation enhances the elaboration of mineralized bone matrix by osteoblast-like cells. In this study, we describe the ongoing characterization of our 3D culture system, including the investigation of interior fluid flow within the scaffolds and early stage integrin expression during hydrodynamic culture. Using theoretical and experimental methods, we have estimated that cells cultured on the interior of microcarrier scaffolds experience an interior nutrient flow velocity between 1 x 10(-3) and 1 x 10(-2) cm/s and maximum shear stress of 0.03 N/m(2). Under these conditions, osteoblast-like cells grew extensively in the interior regions of the scaffold and retained their osteoblastic phenotype as measured by alkaline phosphatase. In addition, flow cytometric analysis of the overall cell population showed that cells constitutively expressed integrin alpha3beta1 during 3D hydrodynamic culture.

Alkaline Phosphatase↗