Biomedical subjects

Emil Chibowski

Publications and source records attributed to Emil Chibowski.

9 recordsLinked to original sources

PubMed2006

Topography and surface free energy of DPPC layers deposited on a glass, mica, or PMMA support.

An investigation of energetic properties of 1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC) layers deposited on glass, mica, and PMMA (poly(methyl methacrylate)) surfaces was carried out by means of contact angles measurements (advancing and receding) for three probe liquids (diiodomethane, water, and formamide). DPPC was deposited on the surfaces from water (on glass and mica) or methanol (on PMMA) solutions. The topography of the tested surfaces was determined with a help of scanning electron microscopy (SEM) and atomic force microscopy (AFM). Using the measured contact angles, the total apparent surface free energy and its components of the studied layers were determined from van Oss et al.'s (Lifshitz-van der Waals and acid-base components, LWAB) and contact angle hysteresis (CAH) approaches. It allowed us to learn about changes in the surface free energy of the layers (hydrophobicity/hydrophilicity) depending on their number and kind of support. It was found that the changes in the energy greatly depended on the surface properties of the substrate as well as the statistical number of monolayers of DPPC. However, principal changes took place for first three monolayers.

Journal Article↗

PubMed2005

Influence of sodium dodecyl sulfate and static magnetic field on the properties of freshly precipitated calcium carbonate.

Properties of calcium carbonate precipitated from aqueous solutions of CaCl(2) and Na(2)CO(3) in the presence of sodium dodecyl sulfate (SDS) and S-S 0.1 T magnetic field (MF) were studied. The nucleation and precipitation processes of CaCO(3) were investigated by pH and zeta potential measurements at 20 +/- 1 degrees C up to 2 h after mixing the solutions. Also the amounts of calcium carbonate deposited on the glass surfaces and its structure were examined. It was found that SDS influences the kinetics of precipitation, crystallographic forms, and crystal size of CaCO(3). The SDS effects are more pronounced in MF presence. A small amount of SDS accelerates transformation of vaterite into calcite, whereas increasing surfactant concentration moderates such a transformation. On the other hand, in all the systems, MF in the presence of SDS causes a slower transformation of vaterite into calcite. These effects are reflected in pH and zeta potential changes, although there is no clear dependence between the SDS amount present during the precipitation and changes of the parameters investigated. It seems that MF effect is most significant at a defined optimal SDS concentration. The results, however, do not allow suggestion of any detailed mechanism of the field interaction.

Adhesiveness↗

PubMed2005

Investigation of the electrokinetic properties of paraffin suspension. 2. In cationic and anionic surfactant solutions.

Electrical phenomena at nonionogenic hydrophobic surfaces (solid or liquid) in water, electrolyte, and/or surfactant solutions still attract research. In part 1 of this paper we described the electrokinetic behavior of paraffin wax suspension in water and electrolyte solutions (NaCl or LaCl3). On the basis of the latest data of water structure near hydrophobic surfaces it was concluded that immobilized water dipoles at the interface can play an essential role in the zeta potential formation. In this paper were investigated the zeta potentials of paraffin wax in cationic surfactants cetyltrimethylammonium bromide, C16H33(CH3)3NBr, and octadecyltrimethylammonium chloride, C18H37(CH3)3NCl, and anionic surfactant sodium dodecyl sulfate, C12H25SO4Na. Also changes in wettability of the paraffin surface due to the surfactant's adsorption were studied via wetting contact angle measurements and calculation of the surface free energy. It was concluded that at a low surfactant concentration (10(-6) M) the water dipole structure still contributes to the zeta potential, but at a higher one the zeta potential is determined by the surfactant molecules' adsorption. A special role of OH- ions is also clearly seen. Moreover, a functional relationship was found between the surface free energy of the surfactant-covered paraffin surface and the zeta potential.

Adsorption↗

PubMed2005

Investigation of the electrokinetic properties of paraffin suspension. 1. In inorganic electrolyte solutions.

Although electrical properties of nonionogenic hydrophobic surface (solid or liquid) in water and/or electrolyte solutions have been studied for many decades, they are still not well recognized, especially as for the nature of the charge and potential origin. Similarly, water structure at such a surface is still extensively studied. One such system is paraffin wax/water (electrolyte). The zeta potentials and the particle diameters of this system were investigated in this paper. To obtain the suspension of paraffin in water or electrolyte solution (NaCl or LaCl3), the mixture was heated to ca. 70 degrees C and then stirred during cooling. For thus obtained suspensions, the zeta potential was determined as a function of time at 20 degrees C. Also the pH effect on the zeta potentials was investigated. The zeta potentials were calculated from Henry's equation. The results obtained by us are in agreement with those obtained earlier by others. They confirm that although H+/OH- are not surface charge creating ions, OH- ions to some extent are zeta potential determining for the paraffin surface. By use of the potentials and diameters, the electric charge for a spherical particle in the shear plane was calculated. These values are small in the range of 10(-3) C/m2. On the basis of the findings of water structure near hydrophobic surface and the calculated charges, it is concluded that in fact the potential may be created by immobilized and oriented water dipoles.

Journal Article↗

PubMed2003

Surface free energy of a solid from contact angle hysteresis.

Nature of contact angle hysteresis is discussed basing on the literature data (Colloids Surf. A 189 (2001) 265) of dynamic advancing and receding contact angles of n-alkanes and n-alcohols on a very smooth surface of 1,1,2,-trichloro-1,2,2,-trifluoroethane (FC-732) film deposited on a silicon plate. The authors considered the liquid absorption and/or retention (swelling) processes responsible for the observed hysteresis. In this paper hysteresis is considered to be due to the liquid film left behind the drop during retreating of its contact line. Using the contact angle hysteresis an approach is suggested for evaluation of the solid surface free energy. Molecular spacing and the film structure are discussed to explain the difference in n-alkanes and n-alcohols behaviour as well as to explain the difference between dispersion free energy gamma(s)(d) and total surface free energy gamma(s)(tot) of FC-732, as determined from the advancing contact angles and the hysteresis, respectively.

Alcohols↗

PubMed2003

Adhesion of in situ precipitated calcium carbonate in the presence and absence of magnetic field in quiescent conditions on different solid surfaces.

Deposition of in situ precipitated calcium carbonate from Na(2)CO(3) and CaCl2 solutions on different substrates, i.e. stainless steel, copper, aluminium, and glass, was investigated at different temperatures, 20 degrees C, 40 degrees C, 60 degrees C and 80 degrees C, both in the absence and presence of S-S 0.1T magnetic field (MF). It was found that in quiescent conditions during 2h the amounts deposited firmly on the surfaces decreased with increasing temperature. If MF was present the deposition was reduced at all temperatures, and depended on the nature of the substrate. The largest MF effect was found on glass at 60 degrees C, which amounted 50% reduction of the deposit. However, at 80 degrees C no deposition was found in the presence of MF on aluminium surface. At this temperature the reproducibility of the experiments was poor, and an additional effect due to the metal surface corrosion (especially that of aluminium and copper) may be thought in alkaline environment of the experiments (pH ca. 10). Based on optical microscope photographs, it was concluded that the amounts of crystallographic forms of CaCO3 depended on the nature of substrate on which the precipitation and then the adhesion took place. To some extent the ratios of CaCO3 forms precipitated were different in the bulk phase than on the substrate surfaces at the same temperature, and this conclusion was based on the X-ray diffractograms. Some possible mechanisms causing MF effects are discussed.

Aluminum↗

PubMed2003

Influence of impurity ions and magnetic field on the properties of freshly precipitated calcium carbonate.

Static magnetic field (MF) effects on the properties of freshly precipitated calcium carbonate have been investigated in the presence of impurity ion Mg(2+), Fe(2+), or SO4(2-). One or both solutions, CaCl2 and Na2CO3, were exposure to MF (0.5T) for 20min at 20 degrees C. Then calcium carbonate was precipitated and zeta potential, pH and light absorbance (lambda=543.3 nm) were measured. The same parameters were also determined for the reference systems in which the solutions were not MF-treated. It was found that in all the systems tested MF effects as determined by the above mentioned parameters had appeared. They depended on the kind of the impurity ion present, as well as on which solution, CaCl2, Na2CO3 or both, MF interacted. For example, if Mg(2+) ion was present in CaCl2 solution, the largest shift in the zeta potential toward higher positive values was observed if Na2CO3 was MF-treated (e.g. from 2 to 12mV) and the same was true as for the maximum in the light absorbance and the pH increase. Interestingly, if (CaCl2 + Mg(2+)) was MF-treated pH of the slurry had decreased. Moreover, a correlation between above mentioned MF effects and the entropy of hydration of the ions has also been found. This points to the changes in the hydrating water structure caused by magnetic field.

Calcium Carbonate↗

PubMed2002

Problems of contact angle and solid surface free energy determination.

The current general problems of formulation and determination of surface free energy are discussed. So far several theories and approaches have been proposed, but formulation of surface and interfacial free energy, as regards its components, is still a very debatable issue. However, as long as no method for determination of real surface free energy quantities is known, even relative values charged with many simplified assumptions are useful for better understanding of the wetting processes. In this paper special focus is concentrated on powdered solids for which direct measurement of the contact angles is not possible. For such solids the porous layer imbibition techniques are most frequently applied. Then, using the wicking results the contact angle is calculated from Washburn's equation. However, such a procedure leads to overestimated contact angle values in comparison to those measured directly on smooth surfaces of the same solid, if such surface can be obtained at all. As a consequence, the solid surface free energy components calculated via such overestimated contact angles are significantly lower than those obtained from contact angles measured directly. Methodologies to avoid this problem are also described.

Journal Article↗

PubMed2001

A Novel Method for Surface Free-Energy Determination of Powdered Solids.

Interfacial solid/liquid interactions play a crucial role in wetting, spreading, and adhesion processes. In the case of a flat solid surface, contact angle measurements are commonly utilized for the determination of the solid surface free energy and its components. However, if such a surface cannot be obtained, then the contact angle can not be measured directly. Usually methods based on imbibition of probe liquids into a thin porous layer or column are applied. In this paper a novel method, also based on the capillary rise, is proposed for the solid surface free-energy components determination. Actually, it is a modification of the thin column wicking method; similar theoretical background can be applied together with that appropriate for the capillary rise method of liquid surface tension determination. The proposed theoretical approach and procedure are verified by using single glass capillaries, and then alumina and ground glass powders were used for the method testing. Thus obtained surface free-energy components for these solids, for both glass and alumina, agree well with the literature values. Copyright 2001 Academic Press.

Journal Article↗