PubMed Health⌕ Search

Biomedical subjects

En-Tang Kang

Publications and source records attributed to En-Tang Kang.

10 recordsLinked to original sources
PubMed2007

Nonvolatile polymer memory device based on bistable electrical switching in a thin film of poly(N-vinylcarbazole) with covalently bonded C60.

A functional polymer (PVK-C60), containing carbazole moieties (electron donors) and fullerene moieties (electron-acceptors) in a molar ratio of about 100:1, was synthesized via covalent tethering of C60 to poly(N-vinylcarbazole) (PVK). The molecular structure and composition of PVK-C60 were characterized by FTIR, Raman, and UV-vis absorption spectroscopy, gel permeation chromatography (GPC), X-ray photoelectron spectroscopy (XPS), and cyclic voltammetry (CyV). The C60-modified PVK exhibited an enhanced glass-transition temperature (Tg = 226 degrees C) and good solubility in organic solvents such as toluene, tetrahydrofuran, chloroform, and N,N-dimethylformamide (DMF). It could be cast into transparent films from solutions. For a thin film of PVK-C60 sandwiched between an indium tin oxide (ITO) electrode and an Al electrode (ITO/PVK-C60/Al), the device behaved as nonvolatile flash (rewritable) memory with accessible electronic states that could be written, read, and erased. The polymer memory exhibited an ON/OFF current ratio of more than 105 and write/erase voltages around -2.8 V/+3.0 V. Both the ON and OFF states were stable under a constant voltage stress of -1 V for 12 h and survived up to 108 read cycles at -1 V under ambient conditions.

Journal Article↗
PubMed2006

Bistable electrical switching and memory effects in a thin film of copolymer containing electron donor-acceptor moieties and europium complexes.

A nonconjugated methacrylate copolymer (PCzOxEu) containing carbazole moieties (electron donors), 1,3,4-oxadiazole moieties (electron acceptors), and europium complexes in the pendant groups was synthesized via free radical copolymerization of methacrylate monomers containing the respective functional groups. The molecular structure and composition of PCzOxEu was characterized by elemental analysis, FT-IR, 1H NMR, 13C NMR, UV-vis absorption and fluorescence spectroscopies, gel permeation chromatography (GPC), X-ray photoelectron spectroscopy (XPS), and cyclic voltammetry (CyV). The resulting copolymer exhibited a relatively high glass transition temperature (Tg approximately 125 degrees C) and good solubility in common organic solvents. It could be cast into transparent films from solutions. For a thin film of PCzOxEu sandwiched between an indium-tin oxide (ITO) electrode and an Al electrode (ITO/PCzOxEu/Al), the structure behaved as a nonvolatile flash (rewritable) memory with accessible electronic states that could be written, read, and erased. The polymer memory exhibited an ON/OFF current ratio up to 10(5), switching response time of approximately 1.5 micros, more than 10(6) read cycles, retention time of more than 8 h, and write/erase voltages of about 4.4 V/-2.8 V under ambient conditions. The roles of oxadiazole moieties in improving the response time and retention time of the memory device were elucidated from the molecular simulation results.

Journal Article↗
PubMed2006

Synthesis and dynamic random access memory behavior of a functional polyimide.

The device under testing was a plastic dynamic random access memory based on a donor-functionalized polyimide (TP6F-PI), which exhibited the ability to write, read, erase, and refresh the electrical states. The device had an ON/OFF current ratio up to 105, promising minimal misreading error. Both the on and off states were stable under a constant voltage stress of 1 V and survived up to 108 read cycles at 1 V.

Journal Article↗
PubMed2006

pH- and temperature-responsive hydrogels from crosslinked triblock copolymers prepared via consecutive atom transfer radical polymerizations.

Well-defined poly((2-dimethyl amino)ethyl methacrylate-co-2-hydroxyethyl methacrylate)-b-poly(N-isopropylacrylamide)-b-poly((2-dimethyl amino)ethyl methacrylate-co-2-hydroxyethyl methacrylate), or P(DMAEMA-co-HEMA)-b-P(NIPAAm)-b-P(DMAEMA-co-HEMA), triblock copolymers were synthesized by consecutive atom transfer radical polymerizations (ATRPs), using ethylene glycol di-2-bromoisobutyrate (Br-EG-Br) as the starting ATRP initiator. The hydroxyl groups of the incorporated HEMA units were used as crosslinking sites for the preparation of smart hydrogels. The so-prepared hydrogels exhibited both temperature- and pH-sensitive behavior derived, respectively, and independently, from the P(NIPAAm) blocks and P(DMAEMA) units, in the crosslinked matrices. The hydrogels exhibited a lower critical solution temperature (LCST) of 31-32 degrees C in aqueous media of pH 1-7, not unlike that of the P(NIPAAm) homopolymer. The swelling ratios and swelling/deswelling kinetics of the hydrogels depended strongly on pH and temperature of the medium. The copolymers were characterized by gel-permeation chromatography, X-ray photoelectron spectroscopy (XPS), Fourier-transform infrared (FTIR) spectroscopy, and (1)H nuclear magnetic resonance ((1)H NMR) spectroscopy. The resultant stimuli-responsive hydrogels were characterized by differential scanning calorimetry (DSC). These stimuli-responsive hydrogels will have potential applications in biomedical areas, such as tissue engineering and drug delivery.

Hydrogels↗
PubMed2006

Cellular response to magnetic nanoparticles "PEGylated" via surface-initiated atom transfer radical polymerization.

A new method to PEGylate magnetic nanoparticles with a dense layer of poly(poly(ethylene glycol) monomethacrylate) (P(PEGMA)) by surface-initiated atom transfer radical polymerization (ATRP) is reported. In this approach, an initiator for ATRP was first immobilized onto the magnetic nanoparticle surface, and then P(PEGMA) was grafted onto the surface of magnetic nanoparticle via copper-mediated ATRP. The modified nanoparticles were subjected to detailed characterization using FTIR, XPS, and TGA. The P(PEGMA)-immobilized nanoparticles dispersed well in aqueous media. The saturation magnetization values of the P(PEGMA)-immobilized nanoparticles were 19 emu/g and 11 emu/g after 2 and 4 h polymerization respectively, compared to 52 emu/g for the pristine magnetic nanoparticles. The response of macrophage cells to pristine and P(PEGMA)-immobilized nanoparticles was compared. The results showed that the macrophage cells are very effective in cleaning up the pristine magnetic nanoparticles. With the P(PEGMA)-immobilized nanoparticles, the amount of nanoparticles internalized into the cells is greatly reduced to <2 pg/cell over a 5 day period. With this amount of nanoparticles uptake, no significant cytotoxicity effects were observed.

Animals↗
PubMed2005

Thermoresponsive comb-shaped copolymer-Si(100) hybrids for accelerated temperature-dependent cell detachment.

Well-defined comb-shaped copolymer-Si(100) hybrids were prepared, via successive surface-initiated atom transfer radical polymerizations (ATRPs) of glycidyl methacrylate (GMA) and N-isopropylacrylamide (NIPAAm), for accelerated cell detachment at a lower temperature. The Si-C bonded comb copolymer consisted of a well-defined (nearly monodispersed) poly(glycidyl methacrylate) (P(GMA)) main chain, a well-defined NIPAAm polymer (P(NIPAAm) block, and well-defined P(NIPAAm) side chains. The ring opening reaction of epoxy groups of the P(GMA) main chain with 2-chloropropionic acid resulted in the immobilization of the alpha-chloroester groups (the ATRP initiators for the NIPAAm side chains) and the concomitant formation of hydroxyl groups. P(NIPAAm) acted as the thermoresponsive side chains of the comb copolymer for control of cell adhesion and detachment, while the P(GMA) main chain with hydroxyl groups provided a local hydrophilic microenvironment. The unique microstructure of the comb copolymer brushes facilitated cell recovery at 20 degrees C (below the lower critical solution temperature (LCST) of P(NIPAAm)) without restraining cell attachments and growth at 37 degrees C. The accelerated detachment of cells indicated that the underlying hydrophilic environment of the comb copolymer brushes contributed to speedy hydration of the P(NIPAAm) segments below the LCST. The thermoresponsive comb copolymer-Si(100) hybrids are potentially useful as adhesion modifiers for cells in silicon-based biomedical devices.

3T3 Cells↗
PubMed2004

Plasma protein adsorption and thrombus formation on surface functionalized polypyrrole with and without electrical stimulation.

A surface modification technique was developed in which heparin was covalently immobilized onto electrically conductive polypyrrole (PPY) film through poly(ethylene glycol) methacrylate (PEGMA) graft copolymerization and subsequent cyanuric chloride activation. In vitro plasma protein adsorption and thrombus formation experiments were carried out on the various films. The PEGMA-graft-copolymerized PPY surfaces with immobilized heparin have good bioactivity indicated by low level of protein adsorption, high ratio of albumin to fibrinogen adsorption, and low thrombus formation, making them potentially good candidates for biomedical applications. Since the PPY film retained significant electrical conductivity after surface modification, the effect of electrical stimulation on protein adsorption and thrombus formation was also evaluated. The covalently immobilized heparin on the PPY film was able to retain its bioactivity after 4 days of immersion in PBS. The film after long-term immersion in PBS also retained sufficient electrical conductivity for electrical stimulation still to be effective for reducing protein adsorption.

Journal Article↗
PubMed2003

High density of immobilized galactose ligand enhances hepatocyte attachment and function.

Galactosylated surface is an attractive substrate for hepatocyte culture because of the specific interaction between the galactose ligand and the asialoglycoprotein receptor on hepatocytes. In this study, we described a scheme to achieve high density of immobilized galactose ligands on polyethylene terephthalate (PET) surface by first surface-grafting polyacrylic acid on plasma-pretreated PET film under UV irradiation, followed by conjugation of a galactose derivative (1-O-(6'-aminohexyl)-D-galactopyranoside) to the grafted polyacrylic acid chains. A high galactose density of 513 nmol/cm(2) on the PET surface was used in this study to investigate the behavior of cultured hepatocyte. This engineered substrate showed high affinity to fluorescein isothiocyanate-lectin binding. Primary rat hepatocytes, when seeded at a density of 2 x 10(5) cells/cm(2), attached to the galactosylated PET substrate at a similar efficiency compared with collagen-coated substrate. The hepatocytes spontaneously formed aggregates 1 day after cell seeding and showed better maintenance of albumin secretion and urea synthesis functions than those cultured on collagen-coated surface.

Acrylic Resins↗