Biomedical subjects

F Josse

Publications and source records attributed to F Josse.

7 recordsLinked to original sources

PubMed2003

Sensitivity of the acoustic waveguide biosensor to protein binding as a function of the waveguide properties.

The aim of this work is to study the effect of operating frequency, piezoelectric substrate and waveguide layer thickness on the sensitivity of the acoustic waveguide sensor during the specific binding of an antibody by a protein. Shear horizontal (SH) wave devices consisting of (a) a LiTaO3 substrate operating at 104 MHz, (b) a quartz substrate operating at 108 MHz and (c) a quartz substrate operating at 155 MHz were coated with a photoresist polymer layer in order to produce acoustic waveguide devices supporting a Love wave. The effect of the thickness of the polymer layer on the Love wave was assessed by measuring the amplitude and phase of the wave before and after coating. The sensitivity of the above three biosensors was compared during the detection of the specific binding of different concentrations of Immunoglobulin G in the range of 0.7-667 nM to a protein A modified surface. Results indicate that the thickness of the polymer guiding layer is critical for obtaining the maximum sensitivity for a given geometry but a trade-off has to be made between the theoretically determined optimum thickness for waveguiding and the device insertion loss. It was also found that increasing the frequency of operation results in a further increase in the device sensitivity to protein detection.

Acoustics↗

PubMed2001

Guided shear horizontal surface acoustic wave sensors for chemical and biochemical detection in liquids.

The design and performance of guided shear horizontal surface acoustic wave (guided SH-SAW) devices on LiTaO3 substrates are investigated for high-sensitivity chemical and biochemical sensors in liquids. Despite their structural similarity to Rayleigh SAW, SH-SAWs often propagate slightly deeper within the substrate, hence preventing the implementation of high-sensitivity detectors. The device sensitivity to mass and viscoelastic loading is increased using a thin guiding layer on the device surface. Because of their relatively low shear wave velocity, various polymers including poly(methyl methacrylate) (PMMA) and cyanoethyl cellulose (cured or cross-linked) are investigated as the guiding layers to trap the acoustic energy near the sensing surface. The devices have been tested in biosensing and chemical sensing experiments. Suitable design principles for these applications are discussed with regard to wave guidance, electrical passivation of the interdigital transducers from the liquid environments, acoustic loss, and sensor signal distortion. In biosensing experiments, using near-optimal PMMA thickness of approximately 2 microm, mass sensitivity greater than 1500 Hz/(ng/mm2) is demonstrated, resulting in a minimum detection limit less than 20 pg/mm2. For chemical sensor experiments, it is found that optimal waveguide thickness must be modified to account for the chemically sensitive layer which also acts to guide the SH-SAW. A detection limit of 780 (3 x peak-to-peak noise) or 180 ppb (3 x rms noise) is estimated from the present measurements for some organic compounds in water.

Acoustics↗

PubMed2000

Real-time detection of organic compounds in liquid environments using polymer-coated thickness shear mode quartz resonators

The selection of sensitive coatings is a critical task in the design and implementation of chemical sensors using coated thickness shear mode quartz crystal resonators (QCRs) for detection in liquid environments. This design or selection is performed through a study of the sorption process in terms of the partition coefficients of the analytes in the coatings. The partition coefficient, which is controlled by the chemical and physical properties of the coating materials, determines the inherent selectivity and sensitivity toward analyte molecules. The selection of the coatings is logically determined by the interactions between coating and target analyte molecules, but can also be made through a systematic variation of the coating's properties. The determination of the partition coefficients is only accurate if all contributions to the total measured frequency shifts, deltafs, of the coated QCR can be established. While mass loading is often assumed to be the dominant factor used in determining partition coefficients, viscoelastic effects may also contribute to deltafs. Both the effect of viscoelastic properties and the effect of mass loading on the sensor responses are investigated by using a network analyzer and oscillator circuit and by characterizing the total mechanical impedance of the loaded sensor. Different types of coatings including rubbery and glassy polymers are investigated, and the targeted analytes include classes of polar compounds (methanol), nonpolar compounds (toluene, xylenes), and chlorinated hydrocarbons (trichloroethylene, tetrachloroethylene, etc). It is seen that changes in viscoelastic properties due to analyte sorption may be significant enough to place the sensor in the nongravimetric regime. However, for most applications involving the detection of relatively low concentrations of organic compounds and the use of acoustically thin films, changes in the complex shear modulus of the coatings contribute less than 5% of the total shift in the series resonant frequency, depending on the coating. In that case, the measured deltafs and, hence, the calculated approximate classification and selection of the coatings for operation in a complex solution of water/analyte molecules.

Journal Article↗

PubMed1999

Characteristics of acoustic plate modes on rotated Y-cuts of quartz utilized for biosensing applications.

Acoustic plate modes (APM) on various quartz substrates have been investigated in order to determine their usefulness for liquid-sensing applications. The modes have been characterized in terms of their mass sensitivity, mode separation, temperature sensitivity, and reproducibility of the experimental results. Promising characteristics are found for rotated Y-cuts of quartz with the direction of acoustic mode propagation being perpendicular to the X-axis of the quartz crystal. Experiments on the detection of immunochemical reactions are performed using different quartz APM sensors, and the results are compared to similar experiments utilizing APM devices on ZX-LiNbO3.

Animals↗

PubMed1997

On-line detection of nonspecific protein adsorption at artificial surfaces.

A detailed understanding of the interaction of proteins with artificial surfaces is essential for many applications in medicine and biochemistry. The affinity of surfaces toward proteins may, for instance, remove pharmacological proteins from media or control the adherence of pathogenic bacteria to protheses. Only a few analytical techniques now exist that can be used to study the binding process in real time, using unlabeled proteins. By investigating the adsorption kinetics of fibrinogen at differently terminated self-assembled monolayers (SAMs) of alkanethiols on thin gold films, it is demonstrated that acoustic plate-mode sensors are a promising analytical tool for studying the adsorption of proteins. In agreement with previous studies for fibrinogen, it is shown in situ that hexa(ethylene glycol)-terminated SAMs (HS(CH2)11 (OCH2CH2)6OH) exhibit very low protein adsorption and that methyl-terminated SAMs (HS(CH2)11CH3) tend to absorb large amounts of protein nonspecifically. The observed adsorption kinetics deviate from classical Langmuir behavior; these kinetics are compatible with a mechanism that involves an unfolding of fibrinogen after adsorption. Film quality is controlled by IR, XPS, and contact angle measurements.

Adsorption↗

PubMed1996

Multifrequency evaluation of different immunosorbents on acoustic plate mode sensors.

Previous studies of acoustic plate modes on ZX-LiNbO3 have indicated that practical mass-sensitive immunosensors can be implemented by using devices with higher frequencies of operation and/or by improving techniques for the immobilization of antibodies. However, it is also known from these studies that the viscoelastic properties of aminosilane films, used for the covalent immobilization of antibodies on the crystal surface, cannot be ignored in the sensor response. In the present work, in an attempt to study the effect of viscoelasticity of the binding film, three different films with different viscoelasticity and binding capacities, an aminosilane, a dextran, and a poly-(etherurethane)-based immunosorbent (XP-5), were prepared on the sensor surface for the immobilization of antibodies. Immunochemical reactions were monitored by the acoustic plate mode sensor at three different frequencies, thus allowing the direct observation of the frequency dependence of mass sensitivity with different films. Depending on the type of immunosorbent, the sensitivity at the third harmonic was enhanced by a factor of 2-5 with respect to the fundamental response. A third acoustic mode at a closely spaced frequency to the third harmonic yielded lower sensitivity values, which indicates that sensitivity depends not only on the frequency of device operation but also on particle displacement amplitude and components of the selected wave. Since antigen binding capacities of the different immunosorbents were determined independently by a modified ELISA test, sensor responses can also be correlated to the immunosorbent structure, and hence the viscoelastic properties. A dual delay line configuration was used which compensates for second-order effects such as temperature variations and nonspecific adsorption.

Antibodies↗

PubMed1994

Immunoassay for native enzyme quantification in biological samples.

In order to detect low levels of enzyme activity, specifically glucose oxidase, in biological samples, an immunoenzymatic assay was developed since currently available methods could not be used because of either their lack of sensitivity or the conditions prevailing in our samples: turbidity of the medium, presence of redox systems other than glucose oxidase, and high concentration of proteins. The principle of the method is to coat a polystyrene surface with a fragment Fc-specific anti-IgG, then with an antibody directed against the looked-for enzyme, which is simultaneously the antigen and the enzyme activity required for immunoenzymatic detection. We applied this concept to biological samples after glucose oxidase administration to mice. This method achieves specificity and sensitivity (20 ng/mL or 1 ng) with samples of biological origin. No marker is needed since the antigen itself possesses an enzyme activity. This method, which requires a small sample volume (50 microL, 20 microL, if necessary), can be extended easily to the many enzymes currently used as markers. It could also be applied to the native enzymes of medical interest for which antibodies and a colorimetric reaction are available.

Animals↗