PubMed Health⌕ Search

Biomedical subjects

F López

Publications and source records attributed to F López.

At least 19 recordsLinked to original sources
PubMed2006

Ultrasonic characterization of granites obtained from industrial quarries of Extremadura (Spain).

The industry of ornamental rocks, such as granites, represents one of the most important industrial activities in the region of Extremadura, SW Spain. A detailed knowledge of the intrinsic properties of this natural stone and its environmental evolution is a required goal in order to fully characterize its quality. In this work, two independent NDT acoustic techniques have been used to measure the acoustic velocity of longitudinal waves in different prismatic granitic-samples of industrial quarries. A low-frequency transceiver set-up, based on a high-voltage BPV Steinkamp instrument and two 50 kHz probes, has been used to measure pulse travel times by ultrasonic through-transmission testing. In complementary fashion, an Erudite MK3 test equipment with an electromagnetic vibrator and two piezoelectric sensors has also been employed to measure ultrasonic velocity by means of a resonance-based method, using the same types of granite varieties. In addition, a comprehensive set of physical/mechanical properties have also been analyzed, according to Spanish regulations in force, by means of alternative methods including destructive techniques such as strength, porosity, absorption, etc. A large number of samples, representing the most important varieties of granites from quarries of Extremadura, have been analyzed using the above-mentioned procedures. Some results obtained by destructive techniques have been correlated with those found using ultrasonic techniques. Our experimental setting allowed a complementary characterization of granite samples and a thorough validation of the different techniques employed, thus providing the industry of ornamental rocks with a non-destructive tool that will facilitate a more detailed insight on the properties of the rocks under study.

Journal Article↗
PubMed2006

Morbidity and mortality in liver retransplantation.

INTRODUCTION: The incidence of orthotopic liver retransplantation (re-OLT) ranges from 6% to 11%. The most frequent causes of early re-OLT are allograft failure, uncontrolled acute rejection, and vascular complications. MATERIALS AND METHODS: A retrospective study of 512 orthotopic liver transplants (OLTs) in 482 patients over 15 years. RESULTS: The incidence of re-OLT was 6.6%, with a higher percentage of men requiring re-OLT than first-time OLT (75.0% vs 63.0%, P < .05). The reasons for re-OLT were thrombosis 21.7%, aneurysm 6.5%, stenosis 3.2%, primary nonfunction (PNF) 21.7%, and chronic rejection or recurrence of the initial disease 40.4%. Complications included PNF (22.0%), acute renal failure (65.6%), postoperative infection (87.5%), and adult respiratory distress syndrome (9.4%; P < .05). No differences were seen in the incidence of septicemia or postoperative hemorrhage. The average survival was much lower in re-OLT (21.8 days) compared with OLT (194.5 days; P < .05). The mortality rates in re-OLT were 100% for primary biliary cirrhosis, 85.7% for HCV, 50% for alcoholic cirrhosis, and 20% for HBV. A direct association between the Model for End-stage Liver Disease (MELD) score and the number of complications was present. DISCUSSION: There was a greater requirement for re-OLT in men and those patients transplanted due to hepatitis B virus cirrhosis and fulminant hepatitis (P < .05). The re-OLT patients had no greater incidence of sepsis compared with the OLT patients, although they did have a greater incidence of primary graft dysfunction, acute renal failure, adult respiratory distress syndrome, and postoperative infection (P < .05). The MELD was a good parameter for predicting graft evolution. Re-OLT in patients with primary biliary cirrhosis and hepatitis C virus was associated with a high degree of mortality.

Humans↗
PubMed2006

[Renal transplantation in HIV-infected patients in Spain].

HIV infection has experienced dramatic improvement in morbidity and mortality with the highly active antiretroviral therapy (HAART). This prompted a reevaluation of organ-solid transplantation as a treatment option for HIV-infected patients. Some trials in the United States have shown that one- and 2-year graft and patient survival is comparable to HIV-negative transplant population. In Europe the experience is still scarce. The aim of this study is to analyse the outcome and the clinical characteristics of HIV-infected patients who received kidney transplantation in Spain in the HAART era. Ten patients were transplanted in our country since 2001. Only one patient was black. The main cause of end-stage renal disease reported was glomerulonephritis. Six of the recipients were coinfected by hepatitis C virus. Inclusion criteria included undetectable HIV viral load and CD4 counts greater than 200/pL. Immunosuppression consisted of steroids, tacrolimus and mycophenolate mofetil, with antibody induction in 4 cases. The median and mean follow-up was 11 and 16.3+/-15.6 (3-46) months, respectively. One recipient lost his graft because of early renal venous thrombosis. The remaining patients are functioning graft with mean serum creatinina level of 1.5 +/- 0.5 mg/dl. Biopsy-proven acute rejection was diagnosed in 4 recipients and was reversed in all cases with antirejection treatment. The plasma HIV RNA levels have remained controlled and CD4 counts have been stable in excess of 200 cell/microL. None of patients have developed AIDS complications. Recipients receiving protease inhibitor-based HAART regimens required significant dosing modification to maintain appropriate tacrolimus levels. Our results show that renal transplantation can be a safe and effective treatment in select HIV-infected patients. Like other series, the acute rejection rate was higher than in non-HIV recipients. The reasons of this rejection incidence remain unknown.

Adult↗
PubMed2005

Soda-anthraquinone, kraft and organosolv pulping of holm oak trimmings.

The operating conditions for an organosolv (ethyleneglycol) and two alkaline (soda-anthraquinone and kraft) processes for obtaining cellulose pulp and paper from holm oak (Quercus ilex) wood trimmings were optimized. A range of variation for each process variable (viz. temperature, cooking time and soda or ethyleneglycol concentration) was established and a central composite experimental design involving three independent variables at three different variation levels was applied. The results obtained with the three cooking processes used were compared and those provided by the kraft process were found to be the best. Thus, the tensile index values it provided (5.9-16.3 N m/g) were 23.7% and 41.5% better than those obtained with the soda-AQ and ethyleneglycol processes, respectively. Also, the kraft process provided the best burst index, brightness and kappa number values. Based on the optimum working ranges, the temperature and cooking time were the variables resulting in the most and least marked changes, respectively, in pulp properties.

Anthraquinones↗
PubMed2005

Live weight estimation of donkeys in central Mexico from measurement of thoracic circumference.

Body measurements (length from nape of neck to the withers; height to withers; length from withers to tail root; length from shoulder to tuber ischii; thoracic circumference; umbilical circumference) were taken and correlated with live weight from 160 donkeys (mean +/- standard deviation = 6 +/- 2.6 years old) in Central Mexico. The age was assessed from dentition. Sex of the donkeys was also recorded. Sex was an important factor of variation (p = 0.011). Live weight was estimated using two allometric models. Model 1: Live weight = beta x (thoracic circumference)beta1. Model 2: Live weight = betao x (height to the withers) beta1 x (thoracic circumference) beta2. Separate prediction equations were produced for males and females, plus one for the total sampled. The 'best fit' models, were those using thoracic circumference to predict the live weight. Males: live weight = 0.018576 x (thoracic circumference)1.84107 (R2 = 0.9839). Females: live weight = 0.031255 x (thoracic circumference)1.72888 (R2 = 0.9839). The equations derived to estimate the live weight of donkeys in Britain, Morocco and Zimbabwe were less satisfactory for use with donkeys from Central Mexico because they overestimated the live weight.

Animals↗
PubMed2005

Use of ozone and/or UV in the treatment of effluents from board paper industry.

The aim of this work has been to study the viability of ozone and/or UV in the treatment of cardboard industry effluents. Several model compounds have been chosen for the experiments: guaicol, eugenol, glucose, acetate and butyrate. Significant differences in the ozonisation rates are observed between phenolic products coming from lignin (eugenol and guaiacol) and aliphatic compounds. Reactions fit in all cases a pseudo-first order kinetics and are influenced by the pH of the solution. Real effluents have also been tested, and the COD decrease has been found to depend on the fatty acids/phenols ratio. Finally, respirometric studies have shown an increase in the BODst in effluents subjected to a mild oxidation, while under stronger conditions a BODst decrease is observed.

Bacteria, Aerobic↗
PubMed2005

Time course and train-of-four fade of mivacurium block during sevoflurane and intravenous anaesthesia.

BACKGROUND AND OBJECTIVE: Volatile anaesthetics inhibit nicotinic acetylcholine receptors at clinically relevant concentrations with higher affinity for the neuronal nicotinic receptor. The inhibitory effects of propofol on nicotinic receptors have only been documented at supraclinical concentrations. The aim of this study was to determine recovery properties and train-of-four (TOF) fade of mivacurium during sevoflurane and propofol anaesthesia, in order to examine any differences both in the enhancement of the neuromuscular block (postjunctional effects) and in TOF fade (prejunctional effects). METHODS: Twenty ASA I-II adult patients were randomly allocated to maintenance of anaesthesia with sevoflurane (end-tidal concentration 2%) or propofol. Neuromuscular block was assessed by acceleromyography and a single dose of mivacurium (0.15 mg kg(-1)) was administered (in the sevoflurane group after 30 min of exposure to sevoflurane). We measured time for recovery of the first twitch of the TOF (T1) from 25-75%, time from 25% recovery of T1 to achieving a TOF ratio (TOFR) of 0.8, TOFR at 50%, 75% and 90% recovery of T1, and height of T1 at TOFR of 0.7 and 0.9. Data were tested using t-test for independent samples. RESULTS: Recovery times (mean (95% confidence interval, CI)) of mivacurium in the sevoflurane group (T1 25-75%, 11.3 (8.1-14.5) min; T1 25%-TOFR0.8, 19.1 (15.7-22.5) min) were significantly longer (P < 0.05) than in the propofol group (T1 25-75%, 6.5 (5.2-7.7) min; T1 25%-TOFR0.8, 11.3 (7.8-10.3) min). No differences were found in the relations between TOFR and T1 or vice versa, between the groups. CONCLUSIONS: Recovery times after a single dose of mivacurium were prolonged by sevoflurane compared with propofol but no differences in TOF fade were observed between the two anaesthetics.

Adult↗
PubMed2005

[Syndromes of overdrainage of ventricular shunting in childhood hydrocephalus].

Overdrainage in ventricular shunting constitutes a difficult to prevent and to treat complication. The authors reviewed a retrospective series of 512 children submitted to a ventricular shunting procedure aimed at analysing factors influencing this type of complication. The causes for the hydrocephalus were congenital (n=172), post-myelomeningocele (n=123), posthemorrhagic (n=103), tumoral (n=64), postmeningitis (n=40) and posttraumatic (n=10). Eighty-eight children (17.8%) evolved with a complication related to the excessive function of the valve. The authors investigated the relationship between hydrocephalus' etiology and type of overdrainage syndromes. The most frequent complication was ventricular catheter block (n=50), followed by symptomatic slit ventricle syndrome (SVS) (n=19), subdural hematoma (n=10) and trapped fourth ventricle (n=9). There were no statistical differences regarding complications for each etiologic subset of hydrocephalus. SVS occurred in 19 children (3.71%), a low rate according to the current literature. Posthemorrhagic and postinfectious hydrocephalus grouped together showed a higher rate of SVS (p=0.005), a feature that we attributed to the cerebral destruction caused by these two conditions. Treatment of SVS was complex and required diverse procedures, applied in an escalated way, which included five decompressive craniectomies. The authors suggest avoiding, as much as possible, the use of ventricular shunts, and recommend the alternative use of new technology valves and neuroendoscopic procedures.

Cerebrospinal Fluid Shunts↗
PubMed2004

Structural cost of shoot modules and its implications on plant potential fitness in a Mediterranean perennial shrub, Retama sphaerocarpa (L.) Boiss.

This paper introduces a methodology to analyse the structural costs on plant potential fitness, empirically exemplified in the hierarchical shoot system of a Mediterranean perennial plant, Retama sphaerocarpa (L.) Boiss. During growing season every year (March-August), the terminal shoot (which is the basic unit of growth) develops inflorescences, flowers and fruits, as well as new shoots (first-, second- and third-order branching shoots) which have the potential to "behave" as terminal shoots in the following year. Different morphological and demographical aspects of the modules within the terminal shoot were measured in 100 terminal shoots selected from different plants of a natural population of R. sphaerocarpa. Complementary samples of 100 shoots of different branching orders were collected to obtain biomass estimations of the terminal shoots. We propose a simple procedure to estimate structural cost (biomass investment) on plant potential fitness (flowering buds) as a methodology for interpreting and comparing the consequences on fitness of different plant growth patterns. The results of this study exemplify how differential allocation patterns among plant structural modules, depending on their position within the shoot system, can be quantified to estimate their influence upon plant potential fitness.

Biomass↗
PubMed2004

Non-linear filtering of ultrasonic signals using neural networks.

Structure noise from inhomogeneous micro-structures makes the detection of flaws present in highly scattering materials difficult. Several techniques have been applied to improve the signal-to-noise ratio (SNR) in order to make flaw detection easier. Linear filtering does not provide good results because both structure noise and flaw signal concentrate energy in the same frequency band. Non-linear filtering can be used to reduce the structure noise of ultrasonic signals. Therefore, neural networks are applied in this work for this purpose. In order to use neural networks for non-linear filtering, dynamic structures must be applied. The easiest way to implement a neural network with the capability of processing temporal patterns is to consider them spatial ones, applying the signal into a tapped delay line of finite extension, that is the input of a static neural network (for example, a multi-layer perceptron). In this work, a dynamic neural network has been built to filter ultrasonic signals with structure noise, and has been trained with the real-time back-propagation algorithm, using as inputs 3000 synthetic ultrasonic signals of 896 samples each. Target signals for training are the same as the ones used as inputs but without noise. The neural network is trained in order to generate as output the target signal when the noisy input one is applied. For testing the performance of the non-linear filter, a new set of 500 noisy signals has been used. The SNR improvement is about 6 dB average. The results show that this non-linear filtering method is quite useful as pre-processing stage in flaw detection systems.

Algorithms↗
PubMed2004

Characterization and hardening of concrete with ultrasonic testing.

In this study, we describe a technique which can be used to characterize some relevant properties of 26 cylindrical samples (15 x 30 cm2) of concrete. The characterization has been performed, according to Spanish regulations in force, by some destructive and ultrasound-based techniques using frequencies of 40 kHz. Samples were manufactured using different water/cement ratios (w/c), ranging from 0.48 to 0.80, in order to simulate different values of compressive strength at each sample. We have correlated the propagation velocity v of ultrasonic waves through the samples to compressive strength R values. As some other authors remark, there exists an exponential relationship between the two above parameters. We have found that a highly linear relationship is present between R and w/c concentration at the samples. Nevertheless, when the same linear model is adopted to describe the relationship between v and w/c, the value of r decreases significantly. Thus, we have performed a multiple regression analysis which takes into account the impact of different concrete constituents (water, cement, sand, etc.) on ultrasound propagation speed. One of the most relevant practical issues addressed in our study is the estimation of the hardening curve of concrete, which can be used to quantify the viability of applying the proposed method in a real scenario. Subsequently, we also show a detailed analysis of the temporal evolution of v and R through 61 days, beginning at the date where the samples were manufactured. After analyzing both parameters separately, a double reciprocal relationship is deduced. Using the above parameters, we develop an NDE-based model which can be used to estimate hardening time of concrete samples.

Journal Article↗
PubMed2004

[Activity of copper-zinc superoxide dismutase in a global ischemic brain lesion model without arterial hypotension].

OBJECTIVE: To determine the behavior of the copper-zinc superoxide dismutase enzyme (SOD/Cu/Zn) in tissue homogenates of rat brains with ischemic lesions produced following the model of global cerebral ischemia without arterial hypotension. MATERIAL AND METHODS: Thirty rats were randomly assigned to five groups of six animals each. Bilateral carotid occlusion was temporarily produced in 24 rats (4 groups) during periods of 5, 15, 30 and 60 minutes, respectively. All the animals were then submitted to reperfusion for 30 minutes and after that, they were sacrificed. A control group of 6 rats was not exposed to arterial occlusion. Cerebral homogenates of the rats' brain were obtained and submitted to spectrophotometer analysis. RESULT: The control group showed the lowest mean values in SOD/Cu/Zn activity (40.60+/-11.42 U/mg of protein), while the highest mean values (60.34+/- 13.52 U/mg of protein) corresponded to the rats submitted to ischemia for 60 minutes, what indicates a statistically significant difference (p = 0.016) between the two groups. CONCLUSIONS: SOD/Cu/Zn activity in rats increases during the production of ischemic cerebral lesions. The analysis of SOD/Cu/Zn activity showed an important tendency to rise from the 30 minutes period of ischemic lesion and reached statistically significant values at 60 minutes from the beginning of the ischemic injury. The experimental model of global brain ischemia without arterial hypotension used in this study constitutes a reliable method for researching cerebral ischemia.

Animals↗
PubMed2003

Comparison of a high-protein disease-specific enteral formula with a high-protein enteral formula in hyperglycemic critically ill patients.

AIMS: To determine whether a specific high-protein enteral formula with a similar caloric percentage of fat and carbohydrates achieves greater control over glycemic levels and reduces insulin requirements in hyperglycemic critically ill patients when compared to a control high-protein enteral formula. DESIGN: A prospective, randomized, controlled, single-blind trial in two University Hospital Intensive Care Units in Spain. METHODS: We enrolled 50 patients with diabetes mellitus or stress hyperglycemia with basal glycemia > or =160 mg/dl and indication for enteral nutrition > or =5 days. Patients with severe kidney failure, liver failure or obesity were excluded from the study. In the first 48 h of admission, after randomization, 26 patients received the study diet and 24 patients received the control diet. The variables were monitored for 14 days. The Harris-Benedict formula with a fixed stress factor of 1.2 was used to calculate caloric needs. Insulin was administered by continuous infusion. An intention-to-treat analysis was performed. RESULTS: On admission, there were no differences between the study and control group in plasma glucose levels (mg/dl) (190.9+/-45 vs 210.3+/-63) and capillary glucose levels (mg/dl) (226.1+/-73 vs 213.8+/-67). After the feeding trial, there were differences between the study and control group in plasma glucose levels (mg/dl) (176.8+/-44 vs 222.8+/-47, P=0.001), capillary glucose levels (mg/dl) (163.1+/-45 vs 216.4+/-56, P=0.001), insulin requirements/day (IU) 8.73 (2.3-27.5) vs 30.2 (21.5-57.1) (P=0.001), insulin/received carbohydrates (UI/g) 0.07 (0.02-0.22) vs 0.18 (0.11-0.35) (P=0.02) and insulin/received carbohydrates/kg 0.98 (0.26-3.59) vs 2.13 (1.44-4.58) (P=0.04). These differences remain in a day-to-day comparison. There were no differences in the analytical tests, or in digestive or infectious complications. Intensive Care Unit length of stay, mechanical ventilation and mortality were similar in both groups. CONCLUSIONS: Hyperglycemic critically ill patients fed with a high-protein diet with a similar caloric percentage of fat and carbohydrates show a significant reduction in plasma glucose levels, capillary glucose levels and insulin requirements in comparison to patients on a conventional high-protein diet. This better glycemic control do not modify Intensive Care Unit length of stay, infectious complications, mechanical ventilation and mortality.

APACHE↗
PubMed2003

Optimization of hydrogen peroxide in totally chlorine free bleaching of cellulose pulp from olive tree residues.

The influence of the operating conditions used in the bleaching of olive wood trimmings pulp (viz. hydrogen peroxide concentration and time) on the yield, kappa index and viscosity of the resulting pulp and on strength-related properties of paper sheets was studied to determine the optimal bleaching conditions of this pulp. Hydrogen peroxide bleached pulps at different sequences (oxygen, ozone, chlorine dioxide and alkaline extractions) were compared. Hydrogen peroxide bleaching proved to be suitable for this pulp. Considerable improvements in viscosity were obtained with respect to other bleaching sequences such as oxygen, ozone and chlorine dioxide. Hydrogen peroxide bleaching decreased the kappa index 51.3% less than ozone bleaching, 25.0% less than chlorine dioxide (D) and 6.3% less combined chlorine dioxide-alkaline extraction (DE). To obtain kappa indices 50.9% and 37.9% lower than the index achieved by hydrogen peroxide, oxygen (LaO(p)) and ozone (LaO(LaZ)R) sequences respectively were needed. Lower-medium levels of hydrogen peroxide concentrations (1-3%) and high reaction times (210 min) proved to be suitable for bleaching of pulp olive trimming residues. This approach could be used on this residue to produce adequately bleached pulp.

Cellulose↗
PubMed2003

Hydrothermal and pulp processing of Eucalyptus.

Hydrothermal processing of Eucalyptus wood was performed at operation temperature of 181 degrees C, processing time or 37.5 min and solid water ratio of 1/6 to ensure a maximum loss of xylan recuperation with minimum cellulose fibre degradation. Under those conditions, the loss of xylan was 22% less than that achieved with the conditions 196 degrees C, 50.6 min and 1/8 (solid/water). IN In addition, an experimental design was used to study the influence of process variables: temperature (145-175 degrees C), pulping time (40-120 min) and ethanol concentration (40-70% weight concentration), on the properties of pulps (yield, kappa number, viscosity, cellulose, xylan, lignin acetyl groups contents and brightness) and paper sheets (stretch index, burst index and tear index) obtained from the solid fraction after hydrothermal treatment of Eucalyptus globulus. Pulps with acceptably high physical and chemical properties can be obtained operating at 175 degrees C for 90 min with 55% ethanol concentration.

Cellulose↗
PubMed2003

Anesthetic technique and development of pneumocephalus after posterior fossa surgery in the sitting position.

OBJECTIVE: Pneumocephalus is a well-known complication of surgical procedures performed with the patients placed in the sitting position. Its incidence and intensity were prospectively studied in 90 consecutive patients undergoing a posterior fossa procedure in this position. Various anesthetic agents, with different effects on cerebral hemodynamics, were used. MATERIAL AND METHODS: Patients were randomly assigned to one of three groups. In group 1 (n=30), anesthesia was induced and maintained with propofol. In group 2 (n=30), anesthesia was induced with thiopental and maintained with isoflurane. In group 3 (n=30), anesthesia was induced with thiopental and maintained with nitrous oxide and low-dose isoflurane. All patients received a load dose and an infusion of fentanyl. A cerebral computed tomography scan was performed to all patients 8 hours after surgery for detecting the presence and location of intracranial air. The size of pneumocephalus was ascertained using the formula for calculating the volume of a spheroid: v = PI / 6. x. y. z. Preoperative diagnosis, existence of shunted or non-shunted hydrocephalus, type and duration of the surgical procedure, detection of intraoperative venous air embolism, and appearance of new neurological symptoms in the postoperative period, were recorded. RESULTS: All patients included in the study developed postoperative pneumocephalus. There were no significant differences (P = 0.133) in the estimated volume of intracranial air between the groups (group 1, volume = 38.3 -/+ 35.4 ml; group 2, volume = 48.9 -/+ 36.3 ml; group 3, volume = 31.5 -/+ 28.4 ml). Only two patients in the group 2 manifested symptoms of neurological involvement due to the pressure exerted by the intracranial air. CONCLUSIONS: Despite the hypothetical diverse effects of the three anesthetic techniques used in this series on cerebral hemodynamics, our results suggest that none of them has a substantial effect on the amount of intracranial air detected after posterior fossa procedures performed in seated individuals. To the best of our knowledge this is the first report that addresses in a prospective manner the effects of several habitual anesthetic techniques on the development of pneumocephalus in patients submitted to posterior fossa procedures performed in the sitting position.

Adolescent↗
PubMed2002

Ethanol-acetone pulping of wheat straw. Influence of the cooking and the beating of the pulps on the properties of the resulting paper sheets.

The influence of independent variables in the pulping of wheat straw by use of an ethanol-acetone-water mixture [processing temperature and time, ethanol/(ethanol + acetone) value and (ethanol + acetone)/(ethanol + acetone + water) value] and of the number of PFI beating revolutions to which the pulp was subjected, on the properties of the resulting pulp (yield and Shopper-Riegler index) and of the paper sheets obtained from it (breaking length, stretch, burst index and tear index) was examined. By using a central composite factor design and the BMDP software suite, equations that relate each dependent variable to the different independent variables were obtained that reproduced the experimental results for the dependent variables with errors less than 30% at temperatures, times, ethanol/(ethanol + acetone) value, (ethanol + acetone)/(ethanol + acetone + water) value and numbers of PFI beating revolutions in the ranges 140-180 degrees C, 60-120 min, 25-75%, 35-75% and 0-1750, respectively. Using values of the independent variables over the variation ranges considered provided the following optimum values of the dependent variables: 78.17% (yield), 15.21 degrees SR (Shopper-Riegler index), 5265 m (breaking length), 1.94% (stretch), 2.53 kN/g (burst index) and 4.26 mN m2/g (tear index). Obtaining reasonably good paper sheets (with properties that differed by less than 15% from their optimum values except for the burst index, which was 28% lower) entailed using a temperature of 180 degrees C, an ethanol/(ethanol + acetone) value of 50%, an (ethanol + acetone)/(ethanol + acetone + water) value of 75%, a processing time of 60 min and a number of PFI beating revolutions of 1750. The yield was 32% lower under these conditions, however. A comparison of the results provided by ethanol, acetone and ethanol-acetone pulping revealed that the second and third process-which provided an increased yield were the best choices. On the other hand, if the pulp is to be refined, ethanol pulping is the process of choice.

Acetone↗