PubMed Health⌕ Search

Biomedical subjects

Fritz H Frimmel

Publications and source records attributed to Fritz H Frimmel.

At least 19 recordsLinked to original sources

Degradation of endocrine disrupting bisphenol A by 254 nm irradiation in different water matrices and effect on yeast cells.

The photodegradation of bisphenol A (BPA) in pure water, surface water and wastewater effluents was studied. The effect of different hydrogen peroxide concentrations on degradation was investigated. The rate of BPA photolysis in the presence of hydrogen peroxide was lower in wastewater effluent than in purified water. Phenol, 1,4-dihydroxylbenzene and 1,4-benzoquinone were identified by means of HPLC as intermediate products of the photodegradation of bisphenol A. In addition, the disappearance of the estrogenic activity of bisphenol A during irradiation was shown by the YES test. Based upon the YES test results, there was a strong decrease of estrogenic activity of parent compound after 120 min irradiation in the presence of hydrogen peroxide.

Benzhydryl Compounds↗

Monitoring the formation of an Aureobasidium pullulans biofilm in a bead-packed reactor via flow-weighted magnetic resonance imaging.

The biofilm-forming fungus, Aureobasidium pullulans DSM 2404, was grown in a bead-packed reactor. Alterations within the reactor were analysed in several cross-sectional slices by magnetic resonance imaging (MRI) with flow contrast. For the first time, biofilm accumulation could be continuously elucidated without using any contrast agents, and the non-stationary flow through the fixed-bed reactor could be visualized. The results indicate that the non-stationary flow through the biofilm reactor changes significantly due to the changing reactor morphology. Preferential flow lines arise during biofilm formation. The accumulation of the biomass was determined and compared to gravimetrical biomass data. The described technique can be used to monitor hydrodynamic transport, and to combine flow-field characteristics with morphological data for the prediction of undesirable reactor processes, e.g. clogging.

Ascomycota↗

Photodegradation of endocrine disrupting chemical nonylphenol by simulated solar UV-irradiation.

The photolysis of nonylphenol (NP) was investigated using a solar simulator in the absence/presence of dissolved organic matter (DOM), HCO3-, NO3- and Fe(III) ions. The effects of different parameters such as initial pH, initial concentration of substrate, temperature, and the effect of hydrogen peroxide concentration on photodegradation of nonylphenol in aqueous solution have been assessed. The results indicate that the oxidation rate increases in the presence of H2O2, Fe(III) and DOM with dissolved organic carbon concentrations not higher than 3 mg L(-1). Phenol, 1,4-dihydroxylbenzene and 1,4-benzoquinone were identified as intermediate products of photodegradation of nonylphenol, through an HPLC method. In addition, the disappearance of the estrogenic activity of nonylphenol during irradiation using YES test was investigated. Based upon the YES test results, there was a strong decrease of estrogenic activity of nonylphenol after 80 h irradiation in the presence of hydrogen peroxide.

Bicarbonates↗

Comparison of leaching tests to determine and quantify the release of inorganic contaminants in demolition waste.

The changes in waste management policy caused by the massive generation of waste materials (e.g. construction and demolition waste material, municipal waste incineration products) has led to an increase in the reuse and recycling of waste materials. For environmental risk assessment, test procedures are necessary to examine waste materials before they can be reused. In this article, results of column and lysimeter leaching tests having been applied to inorganic compounds in a reference demolition waste material are presented. The results show a good agreement between the leaching behaviour determined with the lysimeter unit and the column units used in the laboratory. In view of less time and system requirements compared to lysimeter systems, laboratory column units can be considered as a practicable instrument to assess the time-dependent release of inorganic compounds under conditions similar to those encountered in a natural environment. The high concentrations of elements in the seepage water at the initial stage of elution are reflected by the laboratory column leaching tests. In particular, authorities or laboratories might benefit and have an easy-to-use, but nevertheless reliable, method to serve as a basis for decision-making.

Industrial Waste↗

Swimming pool water--fractionation and genotoxicological characterization of organic constituents.

Swimming pool water treatment in general includes flocculation, sand filtration, and subsequent disinfection with chlorine. The continuous chlorination and input of organic material by bathers in combination with recirculation of the pool water leads to an accumulation of disinfection by-products (DBPs) in the water. Several DBPs have been identified as human carcinogens and are thought to cause allergic asthma. Therefore, the elimination of DBPs is one major aim of pool water treatment. Using membrane filtration as an alternative treatment technology, DBPs can be removed more efficiently than with conventional treatment. In this study membrane filtration and genotoxicity testing were applied for the characterization of pool water constituents and for the identification of the necessary molecular weight cut off of the membrane for an efficient elimination. Two-step membrane filtration revealed that most of the DBPs (as adsorbable organically bound halogen, AOX) were present in the molecular weight fraction below 1000 g/mol. The fraction below 200 g/mol contained more than 30% of the AOX. The distribution of the dissolved organic carbon (DOC) across the fractions was similar to that of the AOX. The genotoxicity was found to be strongest in the low-molecular weight fraction. Thus, considerable DBP removal by membrane treatment requires membranes with low-molecular weight cut offs down to 200 g/mol. The comprehensive elimination of the genotoxic compounds requires further treatment steps.

Adsorption↗

Size exclusion chromatography to characterize DOC removal in drinking water treatment.

A full-scale (110 ML/d) potable water treatment plant (WTP) based on the MIEX process, an innovative new process based on a strong base anion-exchange resin with magnetic properties, has been operating in Perth Western Australia since 2001. This plant has been configured so that a combined MIEX-coagulation (MIEX-C) process can be operated in parallel with a conventional enhanced coagulation (EC) process, allowing comparison of the performance of the two processes. Here, we report the use of size exclusion chromatography (SEC) to compare the removal of different apparent molecular weight (AMW) fractions of DOC by the two processes. Water was sampled from five key locations within the WTP, and SEC was carried out using three different on-line detector systems, DOC-specific detection, UV absorbance detection at lambda = 254 nm, and fluorescence detection (lambda(ex) = 282 nm; lambda(em) = 353 nm). This approach provided information on the chemical nature of the DOC comprising the various AMW fractions. The study showed that the MIEX-C process outperformed the EC process with greater removal of DOC in each of the eight separate AMW fractions identified. While EC preferentially removed the fractions of highest AMW, and those exhibiting the greatest aromatic (humic) character, MIEX-C removed DOC across all AMW fractions and did not appear to discriminate as strongly on the basis of differences in aromatic character or AMW. The results demonstrate the benefits of combining these complementary treatment processes. The study also demonstrates the utility of SEC coupled with multiple detection systems in determining the characteristics of various AMW components of DOC.

Carbon↗

Cross-flow microfiltration with periodical back-washing for photocatalytic degradation of pharmaceutical and diagnostic residues-evaluation of the long-term stability of the photocatalytic activity of TiO2.

The combination of semiconductor photocatalysis with cross-flow microfiltration accompanied by periodical back-washing was investigated in a pilot plant. The investigation included the testing of membrane materials because the membrane must resist the abrasion and the periodical back-washing. Another objective of this investigation was to assess the potential of two different TiO(2) materials (Hombikat UV100 and P25) for continuous photocatalytic degradation of persistent organic pollutants. The study focused on the long-term stability of the photocatalytic activity of TiO(2) during its continuous application. The combination of photocatalysis and cross-flow microfiltration allowed the separation and reuse of TiO(2) after the photocatalytic degradation of clofibric acid, carbamazepine and iomeprol. The investigations showed that the photocatalytic activity of P25 and Hombikat UV100 was constant during continuous usage over several days. This study indicates the high potential of the combination of heterogeneous photocatalytic oxidation processes with cross-flow microfiltration accompanied by periodical back-washing of the membrane. Thus environmentally relevant pharmaceuticals and X-ray contrast media can be transformed and mineralized in a continuous water treatment process.

Carbamazepine↗

Ultrafiltration of nonionic surfactants and dissolved organic matter.

A brownwater sample with a high content of humic substances (HS) was fractionated by multistage ultrafiltration (mst-UF) into five fractions with nominal molecular weights ranging from >30 to <1 kDa. Fractions were characterized with respect to molecular size distribution and structure. Size exclusion chromatography with online DOC detection revealed that mst-UF yielded fractions with decreasing Mp (molecular weight at peak maximum) and polydispersities from nominally large to small mst-UF fractions. 13C MAS NMR analysis showed that the content of carbohydrate structures decreased from the original sample toward smaller molecular weight (MW) fractions, which in turn contained more carboxylic groups and branched aliphatic structures. Specific UV absorbances (SUVA254) were highest in the >30 kDa fraction and decreased with decreasing MW. To evaluate whether separation mechanisms other than size exclusion were of importance during the fractionation, the behavior of low molecular weight model compounds (MC) with a range of polarities was studied. Recoveries decreased with increasing hydrophobicity of the MC. For selected nonylphenol ethoxylates and 4-nonylphenol the recovery correlated well with the hydrophile-lipophile balance value. The presence of dissolved organic matter (DOM) caused an additional loss of hydrophobic MC, possibly because of sorption of the compounds onto DOM fouling layers. The hydrophilic MC caffeine was recovered almost completely (85-86%) regardless of the DOM content of the model solution. It was concluded that size exclusion was the dominant fractionation mechanism for caffeine, whereas hydrophobic interactions played a major role during the mst-UF fractionation of nonpolar contaminants. For a better understanding of the behavior of polyfunctional molecules such as HS, the effect of other physicochemical properties needs to be investigated in further studies.

Caffeine↗

Kinetic study of photocatalytic degradation of carbamazepine, clofibric acid, iomeprol and iopromide assisted by different TiO2 materials--determination of intermediates and reaction pathways.

The light-induced degradation of clofibric acid, carbamazepine, iomeprol and iopromide under simulated solar irradiation has been investigated in aqueous solutions suspended with different TiO2 materials (P25 and Hombikat UV100). Kinetic studies showed that P25 had a better photocatalytic activity for clofibric acid and carbamazepine than Hombikat UV100. For photocatalytic degradation of iomeprol Hombikat UV100 was more suitable than P25. The results can be explained by the higher adsorption capacity of Hombikat UV100 for iomeprol. The study also focuses on the identification and quantification of possible degradation products. The degradation process was monitored by determination of sum parameters and inorganic ions. In case of clofibric acid various aromatic and aliphatic degradation products have been identified and quantified. A possible multi-step degradation scheme for clofibric acid is proposed. This study proves the high potential of the photocatalytic oxidation process to transform and mineralize environmentally relevant pharmaceuticals and contrast media in water.

Adsorption↗

LC-MS analysis in the aquatic environment and in water treatment technology--a critical review. Part II: Applications for emerging contaminants and related pollutants, microorganisms and humic acids.

Environmental contaminants of recent concern are pharmaceuticals, estrogens and other endocrine disrupting chemicals (EDC) such as degradation products of surfactants, algal and cyanobacterial toxins, disinfection by-products (DBPs) and metalloids. In addition, pesticides (especially their transformation products), microorganisms, and humic substances (HS), in their function as vehicles for contaminants and as precursors for by-products in water treatment, traditionally play an important role. The present status of the application of LC-MS techniques for these water constituents are discussed and examples of application are given. Solid-phase extraction with various non-selective materials in combination with liquid chromatography (LC) on reversed-phase columns have been the most widely used methods for sample preconcentration and separation for different compound classes like pesticides, pharmaceuticals or estrogens. Electrospray ionization (ESI) and atmospheric pressure ionization (APCI) are the most frequently used ionization techniques for polar and ionic compounds, as well as for less polar non-ionic ones. The facilities of LC-MS have been successfully demonstrated for different compound classes. Polar compounds from pharmaceuticals used as betablockers, iodinated X-ray contrast media, or estrogens have been determined without derivatization down to ultratrace concentrations. LC-MS can be viewed as a prerequisite for the determination of algal and cyanobacterial toxins and the homologues and oligomers of alkylphenol ethoxylates and their metabolites. Tandem mass spectrometric techniques and the use of diagnostic ions reveal their usefulness for compound-class specific screening and unknown identification, and are also valid for the analysis of pesticides and especially for their transformation products. Structural information has been gained by the application of LC-MS methods to organometallic species. New insights into the structural variety of humic substances have been made possible by FT-ICR-MS due to its ultrahigh mass resolution. Finally, exciting possibilities for rapid detection and identification of microorganisms have been made possible by MALDI and LC-MS methods.

Bacteria↗

LC-MS analysis in the aquatic environment and in water treatment--a critical review. Part I: Instrumentation and general aspects of analysis and detection.

LC-MS has become an invaluable technique for trace analysis of polar compounds in aqueous samples of the environment and in water treatment. LC-MS is of particular importance due to the impetus it has provided for research into the occurrence and fate of polar contaminants, and of their even more polar transformation products. Mass spectrometric detection and identification is most widely used in combination with sample preconcentration, chromatographic separation and atmospheric pressure ionization (API). The focus of the first part of this review is directed particularly toward instruments and method development with respect to their applications for detecting emerging contaminants, microorganisms and humic substances (HS). The current status and future perspectives of 1) mass analyzers, 2) ionization techniques to interface liquid chromatography (LC) with mass spectrometry (MS), 3) methods for preconcentration and separation with respect to their application for water analysis are discussed and examples of applications are given. Quadrupole and ion trap mass analyzers with electrospray ionization (ESI) and atmospheric pressure chemical ionization (APCI) are already applied in routine analysis. Time-of-flight (TOF) mass spectrometers are of particular interest for accurate mass measurements for identification of unknowns. For non-polar compounds, different ionization approaches have been described, such as atmospheric pressure photoionization (APPI), electrochemistry with ESI, or electron capture ionization with APCI. In sample preconcentration and separation, solid phase extraction (SPE) with different non-selective sorbent materials and HPLC on reversed-phase materials (RP-HPLC) play the dominant role. In addition, various on-line and miniaturized approaches for sample extraction and sample introduction into the MS have been used. Ion chromatography (IC), size-exclusion chromatography (SEC), and capillary electrophoresis (CE) are alternative separation techniques. Furthermore, the issues of compound identification, matrix effects on quantitation, development of mass spectral libraries and the topic of connecting analysis and toxicity bioassays are addressed.

Journal Article↗

Photoformation of low-molecular-weight organic acids from brown water dissolved organic matter.

This work describes the effects of simulated solar UV light on the bulk properties of dissolved organic matter (DOM) of bog lake water and on the formation of low-molecular-weight organic acids (LMWOAs). By means of size-exclusion chromatography it was shown that the more hydrophilic moieties of the DOM were preferentially photodegraded while the more hydrophobic ones remained relatively unaffected or were even formed. The combined photochemical-biological degradation proved to be more important than the pure photochemical mineralization. Formic, acetic, pyruvic, oxalic, malonic, and succinic acids were identified as important degradation products. Their contribution to the dissolved organic carbon increased from 0.31% before to 6.4% after 24 h irradiation. About 33% of the bioavailable photoproducts of DOM were comprised of these LMWOAs. The influence of nitrate on the formation of carboxylic acids could not be observed in the investigated system. Kinetic experiments indicated that degradation of LMWOAs occurred simultaneously during irradiation experiments, alpha-oxygen-substituted LMWOAs being more amenable to these processes. Dissolved iron acted as a catalyst of DOM photodegradation and LMWOA photoformation. Copper played an antagonistic role in the irradiation experiments, reducing the formation of formic, acetic, and malonic acids while increasing the formation of oxalic acid.

Acetic Acid↗

Molecular weight characteristics of humic substances from different environments as determined by size exclusion chromatography and their statistical evaluation.

Recorded molecular weights (MWs) for humic substances (HS) range from a few hundred to millions of daltons. For purposes of defining HS as a specific class of chemical compounds, it is of particular importance to ascertain if this broad range of MWs can be attributed to actual variability in molecular properties or is simply an artifact of the analytical techniques used to characterize HS. The main objectives of this study were (1)to establish if a preferential range of MWs exists for HS and (2) to determine any consistent MW properties of HS. To reach the goal, we have undertaken an approach to measure under standardized conditions the MW characteristics of a large set of HS from different natural environments. Seventy-seven humic materials were isolated from freshwater, soil, peat, and coal, such that each possessed a different fractional composition: humic acid (HA), fulvic acid (FA), and a nonfractionated mixture of HA and FA (HF). Size exclusion chromatography (SEC) was used as the analytical technique to determine molecular weight characteristics. The MW distributions were characterized by number (Mn) and weight (Mw) average MW, and by polydispersity. The complete range of Mw values varied within 4.7-30.4 kDa. The maximum Mw values were observed for peat HF and soil HA, whereas the smallest weights were measured for river water HF. Maximum values of polydispersity (3.5-4.4) were seen for peat HF and soil HA, while much lower values (1.6-3.1) were found for all preparations isolated with XAD-resins. Statistical evaluation showed consistent Mw and Mn variations with the HS source, while polydispersity was mostly a function of the isolation procedure used. A conclusion was made that HS have a preferential range of MW values that could characterize them as a specific class of chemical compounds.

Chromatography, Gel↗

Electron-beam treatment of aromatic hydrocarbons that can be air-stripped from contaminated groundwater. 2. Gas-phase studies.

The electron-beam (EB) degradation of volatile aromatics (benzene, toluene, ethylbenzene, xylenes: BTEX) in groundwater strip gas, which in the present work has been modeled by the introduction of the desired aromatic(s) to a stream of air or another gas, such as oxygen, is initiated essentially by the addition of *OH radicals to the aromatic ring, giving rise to hydroxycyclohexadienyl radicals, which form the corresponding peroxyl radicals upon addition of oxygen. As studied in some detail with benzene as a BTEX representative, various reactions of these lead to numerous oxidation products in a cascade of reactions, including the decomposition of products under the prevailing conditions of high turnover of the initial aromatic. Importantly, hydroxycyclohexadienylperoxyl radical formation is partly reversible, and the reactions of the hydroxycyclohexadienyl radicals, which thus have a significant presence in these systems, must therefore also be taken into consideration. In the gas phase, in contrast to the aqueous phase (see Part 1), the reactions of the hydroxycyclohexadienyl radicals lead to oligomeric products that appear to contribute, in addition to ionic clusters, to nucleation for the aerosols observed. Various nitrated products, among them nitrophenols, are observed when air is used for the stripping. However, these studies did not clear the pilot plant stage, since BTEX degradation using a bioreactor carried out in parallel was so successful that the EB technology was judged to be noncompetitive. As for the latter, expensive equipment consisting of a stripper, the EB machine, and an aerosol precipitator would be required. The condensed aerosols are biorefractory and would require further treatment for detoxification.

Aerosols↗

Combined advanced oxidation and biodegradation of industrial effluents from the production of stilbene-based fluorescent whitening agents.

Three different industrial wastewaters from the production of stilbene-based fluorescent whitening agents were investigated with regard to the applicability of advanced oxidation processes combined with biodegradation. Oxidation processes included the application of ozone, hydrogen peroxide, UV-radiation and Fenton's reagent (Fe(2+)/H(2)O(2)). Characterization of the combined chemical-biological treatment was done by sum parameters and HPLC analysis. In addition, toxicity was determined using the luminescence inhibition test. Results showed that processes producing OH-radicals without the need of UV-irradiation proved to be suited for the oxidation of all three wastewaters. H(2)O(2)/UV processes were ineffective due to the high inner filter effect of the effluents. Comparing the combined oxidative-biological process with biological treatment, the applied pre-oxidation steps did not always lead to a significant improvement of the biological degradation. In one case, an inverted treatment starting with biodegradation followed by oxidation turned out to be the preferable procedure. After oxidation with ozone or ozone combined with UV-irradiation, an increase in toxicity was partly observed indicating the formation of toxic intermediate products. In some cases samples had to be diluted before the biodegradation step to achieve a better biodegradability.

Biodegradation, Environmental↗

Fate of pharmaceuticals--photodegradation by simulated solar UV-light.

The fate of pharmaceuticals in surface waters under solar irradiation was investigated. Photodegradation of pharmaceuticals caused by sun irradiation may be of major significance in the natural elimination process. Based on a data compilation from the literature, the lipid lowering agent metabolite clofibric acid, the iodinated X-ray contrast media iomeprol, which contribute to the adsorbable organic halogen compounds, and the antiepileptic drug carbamazepine were selected. The irradiation experiments were carried out in batch experiments with simulated UV-sunlight. The photodegradation of the pharmaceuticals showed a pseudo-first-order kinetics. The objective of this investigation was to demonstrate that the extent of photoinduced degradation of pharmaceuticals can vary significantly for the different pharmaceuticals and it strongly depends on the water constituents present in solution. The influences of different initial pharmaceutical concentrations, the presence of other pharmaceuticals like carbamazepine or clofibric acid and the presence of natural organic matter on the photochemical degradation rate of pharmaceuticals in aqueous solutions were investigated. Analyses of the pharmaceuticals and their photodegradation products were carried out by high performance liquid chromatography with diode-array and fluorescence detection.

Carbamazepine↗

Ligand exchange rate of metal-NOM complexes by EDTA.

Metal complexation by natural ligands is important for metal transport and distribution in surface and ground water. The goal of the work was to study the ligand exchange rate for two important metal ions in natural aquatic systems (Al, Fe) was determined using EDTA and natural organic matter (NOM) of humic type as ligands. After adding EDTA to a solution containing metal-NOM complexes, these complexes dissociated and metal-EDTA complexes were formed. Metal-NOM complexes were separated from metal-EDTA complexes with the help of size-exclusion chromatography and detected by on-line inductively coupled plasma-mass spectrometry (ICP-MS). Injecting the samples into the system over time after addition of EDTA allowed us to measure the rate of the exchange of NOM by EDTA. The experiments could be well described with a first-order rate law assuming that the dissociation of the metal-NOM complexes is the rate-determining step. The exchange rate of Fe was found to be faster than that of Al. This corresponds well with the exchange rate of water molecules from the coordination sphere of the metal ions, which is also faster for Fe than for Al. Furthermore, the UV and the fluorescence signal of the chromatograms were measured. The results indicate that no disaggregation of NOM molecules took place, although about 75-85% of the aggregate-forming metal ions exchanged NOM by EDTA in their coordination sphere. This suggests clearly the fundamental role of NOM in colloidal transport of metals and in their bioavailability.

Chelating Agents↗