Biomedical subjects

Gianluca Ciardelli

Publications and source records attributed to Gianluca Ciardelli.

10 recordsLinked to original sources

PubMed2006

Towards the design of highly selective recognition sites into molecular imprinting polymers: a computational approach.

A computational approach to simulate the formation of possible imprinted polymers in acetonitrile solution for theophylline (THO) is proposed, using combined molecular dynamics (MD), molecular mechanics (MM), docking and site mapping computational techniques. Methacrylic acid (MAA) and methylmethacrylate (MMA) monomers are used to simulate possible homo and copolymer structures. The model is able predict binding affinity and selectivity when considering THO analogues, such as caffeine, theobromine, xanthine and 3-methylxanthine. Comparison with available experimental data is proposed.

Biosensing Techniques↗

PubMed2006

Enzymatic erosion of bioartificial membranes to control drug delivery.

The preparation of an enzymatic controlled drug release system from blends of PVA/starch/alphaA, in the form of films, is described. It was shown that alphaA hydrolyses the starch within these films, resulting in a time-dependent change of the porosity in the matrix. Films were characterized by calorimetric analysis to study the interactions between the enzyme and the polymeric constituents at the molecular level. The presence of alphaA, in fact, influenced the PVA crystallization in the blends. Release tests and permeability experiments were carried out to evaluate the transport properties of the films. An increase in porosity and permeability was observed by increasing alphaA content (16-28 wt.-%). Films loaded with theophylline and caffeine were also prepared to analyze drug release properties of the matrix. Drug release kinetics were coherent with the measured changes in porosity: at higher alphaA concentrations the amount of released drug increased under the influence of diffusion and erosion processes. The results obtained are promising for the realization of drug delivery devices for a rapid release or for the release of poorly soluble drugs which usually remain entrapped in the matrix.SEM images of a PVA/starch/alphaA film before (A) and after (B) the erosion.

Biocompatible Materials↗

PubMed2006

Supported imprinted nanospheres for the selective recognition of cholesterol.

The preparation of innovative polymeric systems using molecular imprinting technology for application in extracorporeal blood purification is described. Membranes based on a methylmethacrylate-co-acrylic acid copolymer, produced through the phase inversion method, were modified introducing into their structure specific binding sites for cholesterol molecule by adding molecularly imprinted nanoparticles in the membrane matrix. Membranes prepared are intended to selectively remove cholesterol from the blood by using interactions at a molecular level, between the membrane/nanoparticles devices and the template, created during the preparation of polymers. Three polymeric systems in form of nanoparticles were prepared differing in the polymerisation solvent (a mixture of acetonitrile and ethanol (1:1) or pure ethanol), and the molar ratio between the functional monomer and the cross-linker (2.3:1 and 1:1). Two out of three of the prepared polymers showed a very good template rebinding capacity both in phosphate buffer solution (pH 6.9) and in ethanol. In particular the nanoparticles rebound 115.4 mg cholesterol/g polymer in buffer solution, and 57 mg cholesterol/g polymer in ethanol. The deposition of the nanoparticles on the surface of the phase inversion membranes produced devices with interesting rebinding performances towards cholesterol in buffer solution: a specific recognition of 14.09 mg cholesterol/g system (membrane and nanoparticles) was detected, indicating maintained binding capacity of supported particles as well.

Biosensing Techniques↗

PubMed2006

Materials for peripheral nerve regeneration.

Recent efforts in scientific research in the field of peripheral nerve regeneration have been directed towards the development of artificial nerve guides. We have studied various materials with the aim of obtaining a biocompatible and biodegradable two layer guide for nerve repair. The candidate materials for use as an external layer for the nerve guides were poly(caprolactone) (PCL), a biosynthetic blend between PCL and chitosan (CS) and a synthesised poly(ester-urethane) (PU). Blending PCL, which is a biocompatible synthetic polymer, with a natural polymer enhanced the system biocompatibility and biomimetics, fastened the degradation rates and reduced the production costs. Various novel block poly(ester-urethane)s are being synthesised by our group with tailored properties for specific tissue engineering applications. One of these poly(ester-urethane)s, based on a low molecular weight poly(caprolactone) as the macrodiol, cycloesandimethanol as the chain extender and hexamethylene diisocyanate as the chain linker, was investigated for the production of melt extruded nerve guides. We studied natural polymers such as gelatin (G), poly(L-lysine) (PL) and blends between chitosan and gelatin (CS/G) as internal coatings for nerve guides. In vitro and in vivo tests were performed on PCL guides internally coated either with G or PL to determine the differences in the quality of nerve regeneration associated with the type of adhesion protein. CS/G natural blends combined the good cell adhesion properties of the protein phase with the ability to promote nerve regeneration of the polysaccharide phase. Natural blends were crosslinked both by physical and chemical crosslinking methods. In vitro neuroblast adhesion tests were performed on CS/G film samples, PCL/CS and PU guides internally coated with G to evaluate the ability of such materials towards nerve repair.

Absorbable Implants↗

PubMed2005

Free radical generation upon plasma treatment of cotton fibers and their initiation efficiency in surface-graft polymerization.

Low-temperature plasma was used to activate mercerized cotton fabrics, to be followed by grafting with various methacrylates. Careful analysis of the experimental electron spin resonance (ESR) lineshapes of cotton samples treated at different RF powers made it possible to recognize and quantify four different species of free radicals still persistent 30 h after irradiation in the samples maintained under inert atmosphere. The decay rate of these species at room temperature was also evaluated with the analysis of the time evolution of the ESR spectra. The nature of the free radical species actually involved in the monomer grafting reaction has been discussed for cotton fabrics prepared under different plasma treatment conditions by analyzing the ESR lineshapes.

Journal Article↗

PubMed2004

Acrylonitrile-acrylic acid copolymer membrane imprinted with uric acid for clinical uses.

The preparation of new polymeric membranes using molecular imprinting technology for application in blood filtration devices is described. Membranes, based on an acrylic acid-acrylonitrile copolymer, produced through phase inversion, were modified by introducing specific binding sites for uric acid into their structure. The materials prepared are intended for use to selectively remove uric acid from the blood in the case of increased serum uric acid values associated with different pathologies. The interactions at a molecular level between the membrane forming copolymer and the template were investigated by means of calorimetry, infrared spectroscopy and morphological analysis. The presence of interactions between the template and the copolymer, and a good thermal stability of the imprinted membranes were observed. In addition, the results of rebinding tests on the imprinted membranes indicated a good capacity of molecular recognition for the template and satisfactory selectivity properties towards compounds of similar structure such as theophylline. Membrane permeability values suggest their application as (ultra) haemofiltration devices. Poly(acrylonitrile-co-acrylic acid) membrane.

Acrylates↗

PubMed2004

Innovative tissue engineering structures through advanced manufacturing technologies.

Awide range of rapid prototyping (RP) techniques for the construction of three-dimensional (3-D) scaffolds for tissue engineering has been recently developed. In this study, we report and compare two methods for the fabrication of poly-(epsilon-caprolactone) and poly-(epsilon-caprolactone)-poly-(oxyethylene)-poly-(epsilon-caprolactone) copolymer scaffolds. The first technique is based on the use of a microsyringe and a computer-controlled three-axis micropositioner, which regulates motor speed and position. Polymer solutions are extruded through the needle of the microsyringe by the application of a constant pressure of 10-300 mm Hg, resulting in controlled polymer deposition of 5-600 microm lateral dimensions. The second method utilises the heating energy of a laser beam to sinter polymer microparticles according to computer-guided geometries. Materials may be fed either as dry powder or slurry of microparticles. Both powder granulometry and laser working parameters influence resolution (generally 300 microm x 700 microm), accuracy of sintering and surface and bulk properties of the final structures. The two RP methods allow the fabrication of 3-D scaffolds with a controlled architecture, providing a powerful means to study cell response to an environment similar to that found

Animals↗

PubMed2003

Membrane contactors for textile wastewater ozonation.

This paper deals with the application of a membrane contactor for the ozone treatment of textile wastewater. Ceramic (alpha-Al(2)O(3)) membranes were chosen because of their ozone resistance. A thin metal oxide (TiO(2) and gamma-Al(2)O(3)) layer was deposited on the membrane surface to eliminate large defects. Membranes were characterized by bubble pressure and gas permeability tests. Mass transfer coefficients were calculated by using the double-film theory. Decolorization kinetics were studied with model dye solutions. Decolorization experiments with a real exhausted dyebath (untreated and after biological treatment) were also carried out. The potential advantages of membrane contactors for the treatment of these types of effluents are demonstrated.

Journal Article↗

PubMed2002

Photocatalytic degradation of actual textile industrial wastewater in aqueous suspensions of polycrystalline TiO2.

Heterogeneous photocatalytic oxidation of contaminants present in wastewater produced by a textile industry was carried out. The samples were withdrawn from the plant before and after a traditional biological treatment. The effluents were named A and A' (before the biological treatment), B and B' (after the biological treatment). Polycrystalline TiO2 (Degussa P25) was used as the catalyst in a batch photoreactor with immersed lamp. An almost complete decolorization was observed after about 0.5 divided by 1 hours for both kinds of effluents, but the decrease of the total organic carbon (TOC) concentration occurred more slowly. The influence of some chemical oxidants, i.e. ozone, hydrogen peroxide and peroxydisulfate on the photo-oxidation rate was also investigated. After addition of H2O2 or S2O8(2-) TOC decreased more quickly only for B and B'. The runs performed by using O3 as bubbling gas showed a mineralization rate higher than that observed in the presence of O2.

Catalysis↗

PubMedDate not supplied

Blends of poly-(epsilon-caprolactone) and polysaccharides in tissue engineering applications.

Bioartificial blends of poly-(epsilon-caprolactone) (PCL) with a polysaccharide (starch, S; dextran, D; or gellan, G) (PCL/S, PCL/D, PCL/G 90.9/9.1 wt ratio) were prepared by a solution-precipitation technique and widely characterized by differential scanning calorimetry analysis (DSC), Fourier transform infrared-attenuated total reflectance spectroscopy (FTIR-ATR), optical microscopy (OM), wide-angle X-ray diffraction analysis (WAXD), and thermogravimetry (TGA). DSC showed that the polysaccharide reduced the crystallinity of PCL and had a nucleation effect, which was also confirmed by OM analysis. Hoffman-Weeks analysis was performed on PCL and blend samples allowing calculation of their equilibrium melting temperatures (). WAXD showed that the crystalline unit cell type was the same for PCL and blends. FTIR-ATR did not evidence interactions between blend components. Thermal stability was affected by the type of polysaccharide. Microparticles (<125 microm) were produced from blends by cryogenical milling and characterized by scanning electron microscopy analysis (SEM). Selective laser sintering (SLS), a new rapid prototyping technology for scaffold fabrication, was applied to sinter blend microparticles according to a PC-designed two-dimensional geometry (strips and 2 x 2 mm(2) square-meshed grids). The optimal experimental conditions for sintering were established and laser beam parameters (beam speed, BS, and power, P) were found for each blend composition. Morphology of sintered objects was analyzed by SEM and found to be dependent on the morphology of the sintered powders. Sintered samples were analyzed by chemical imaging (CI), FTIR-ATR, DSC, and contact angle analysis. No evidence of the occurrence of degradation phenomena was found by FTIR-ATR for sintered samples, whereas DSC parameters of PCL and blends showed changes which could be attributed to some molecular weight decrease of PCL during sintering. CI of sintered samples showed that the polysaccharide phase was homogeneously dispersed within the PCL matrix, with the only exception being the PCL/D blend. The contact angle analysis showed that all samples were hydrophilic. Fibroblasts were then seeded on scaffolds to evaluate the rate and the extent of cell adhesion and the effect of the polysaccharides (S, D, G) on the bioactivity of the PCL-based blends.

Animals↗