Biomedical subjects

Gianluca Giavaresi

Publications and source records attributed to Gianluca Giavaresi.

At least 19 recordsLinked to original sources

PubMed2007

In vitro and in vivo performance of a novel surface treatment to enhance osseointegration of endosseous implants.

OBJECTIVE: This article shows the in vitro and in vivo characterization of a new biomimetic treatment developed to enhance the osseointegration of titanium dental implants. STUDY DESIGN: A novel biomimetic treatment of titanium was developed. Its physicochemical properties and biologic and in vivo performance were considered and studied. Mineralization capability was assessed by soaking test in simulated body fluid solution, and cytocompatibility was assessed using osteoblast-like MG63 cell culture. Histomorphometric analysis was performed at 3 time points using a sheep animal model. RESULTS: In vitro tests confirmed the biomimetic potential of the considered novel treatment. Histomorphometric analysis indicated its potential for rapid and good-quality osseointegration. CONCLUSION: The in vitro and in vivo test results indicated that the proposed novel treatment possesses a significant potential to increase the rate of osteointegration of titanium for endosseous dental implants.

Analysis of Variance↗

PubMed2007

In vitro study comparing two collageneous membranes in view of their clinical application for rotator cuff tendon regeneration.

Tenocytes were isolated from the rotator cuff tendons of healthy (HT) and glucocorticoid (GC)-treated rats (GCT) and were cultured on polystyrene wells (TCP) as control, and on 2 de-cellularized collagen matrices: porcine small intestinal submucosa (SIS), and human dermal matrix (Graftjacket, GJ). At 3 and 7 days cell proliferation and synthesis were evaluated. Proliferation of HT tenocytes increased between experimental times for both tested membranes, but already at 3 days, HT tenocytes cultured on GJ showed the highest WST-1 value. The collagen-I (CICP) synthesis on GJ membrane did not change between experimental times and was significantly higher than TCP and SIS at 7 days. Proteoglycans (PG), and fibronectin (FBN) synthesis increased when HT were cultured on GJ, between experimental times, and both PG and FBN synthesis on GJ membrane were higher than TCP and SIS at 7 days. GC determined decreases in cell proliferation, CICP and PG syntheses at 3 days of culture on TCP when compared to HT tenocytes while a decrease in WST-1 was maintained at 7 days. CICP, PG and FBN (only at 3 days) syntheses were significantly higher in GCT tenocytes cultured on GJ. The negative effects on GC on GCT tenocytes cultured on membrane were particularly evident on SIS for CICP (-18%) and FBN (-67%) synthesis. The obtained results support the conclusion that GJ is more suitable than SIS as a scaffold for in situ tissue engineering and for the in vitro bioengineering of tendons to heal massive tears of the rotator cuff tendon.

Animals↗

PubMed2007

Crimp morphology in relaxed and stretched rat Achilles tendon.

Fibrous extracellular matrix of tendon is considered to be an inextensible anatomical structure consisting of type I collagen fibrils arranged in parallel bundles. Under polarized light microscopy the collagen fibre bundles appear crimped with alternating dark and light transverse bands. This study describes the ultrastructure of the collagen fibrils in crimps of both relaxed and in vivo stretched rat Achilles tendon. Under polarized light microscopy crimps of relaxed Achilles tendons appear as isosceles or scalene triangles of different size. Tendon crimps observed via SEM and TEM show the single collagen fibrils that suddenly change their direction containing knots. The fibrils appear partially squeezed in the knots, bent on the same plane like bayonets, or twisted and bent. Moreover some of them lose their D-period, revealing their microfibrillar component. These particular aspects of collagen fibrils inside each tendon crimp have been termed 'fibrillar crimps' and may fulfil the same functional role. When tendon is physiologically stretched in vivo the tendon crimps decrease in number (46.7%) (P<0.01) and appear more flattened with an increase in the crimp top angle (165 degrees in stretched tendons vs. 148 degrees in relaxed tendons, P<0.005). Under SEM and TEM, the 'fibrillar crimps' are still present, never losing their structural identity in straightened collagen fibril bundles of stretched tendons even where tendon crimps are not detectable. These data suggest that the 'fibrillar crimp' may be the true structural component of the tendon crimp acting as a shock absorber during physiological stretching of Achilles tendon.

Achilles Tendon↗

PubMed2006

Comparative study of different tendon grasping techniques for arthroscopic repair of the rotator cuff.

BACKGROUND: One cause of early failure of rotator cuff repairs is the pull out of the suture through the tendon. The aims of this study were to investigate the initial strength and failure mode of different tendon grasping techniques and to evaluate an alternative stitch proposed for arthroscopic repair of rotator cuff tendons. METHODS: Four different stitches were investigated: simple stitch, Mattress, modified Mason-Allen and simple stitch closed over a horizontal loop. The last stitch was proposed as an alternative to the modified Mason-Allen stitch since the former is simpler to sew arthroscopically than the latter. The experimental procedure was designed to assess the mechanical behaviour of the stitches. Tests were performed using sheep infraspinatus tendons. Two different non-absorbable sutures were used. Each specimen was preloaded with about 30 N and then loaded to failure. RESULTS: No significant difference was found in compliance among the four investigated stitches. Conversely, the tensile strength of the simple stitch and Mattress was lower than the tensile strength of the other two stitches, while no significant difference was observed between the modified Mason-Allen and the simple stitch closed over a horizontal loop. The maximum grasping power of these two 'reinforced' stitches was achieved only with the high-strength suture. INTERPRETATION: The simple stitch closed over a horizontal loop seems to be an attractive alternative to the modified Mason-Allen for arthroscopic repair of the rotator cuff and it seems recommendable instead of simple or Mattress stitches. The use of a high-strength suture would increase the tensile strength of the grasping in the case of good quality tendon tissue.

Animals↗

PubMed2006

Early effects of extracorporeal shock wave treatment on osteoblast-like cells: a comparative study between electromagnetic and electrohydraulic devices.

BACKGROUND: Extracorporeal shockwave therapy (ESWT) has been increasingly applied to treat orthopedic and musculoskeletal pathologies. ESWT involves mechanical perturbations that, as with other physical therapies, can result in mechanical stimuli to a large number of cells, including bone cells. The aim of this study was to evaluate the effects of shock waves on osteoblast-like cells (MG63) when using two different generators of shock waves (electrohydraulic and electromagnetic devices), in terms of cell damage, cell viability, osteogenic phenotype expression, and cytokine production. METHODS: MG63 cells were suspended in 1.5 mL screw-cap cryotubes (1 x 10 cells/mL), containing phosphate buffer solution (PBS), which were maintained at 37 degrees C during all the experimental times. Two levels of energy flux density (EFD) were evaluated for each device: 0.15 to 0.18 mJ/mm2 and 0.40 mJ/mm2. Cells were then cultivated for 72 hours starting from a concentration of 1 x 10 cells/mL, and biological activity and viability were evaluated 24 and 72 hours after treatment. RESULTS: The results obtained demonstrate that the factors most affecting osteoblast activity involve both the device and the level of EFD selected, and they must be considered all together. CONCLUSIONS: The use of the electromagnetic device and a level of EFD lower than 0.40 mJ/mm2 would appear to induce fewer immediate cytodestructive effects and better stimulate subsequent proliferation and the synthetic activity of MG63.

Cell Survival↗

PubMed2005

Transplantation of chondrocytes seeded on collagen-based scaffold in cartilage defects in rabbits.

Recent success in tissue engineering by restoring cartilage defects by transplanting autologous chondrocyte cells on a three-dimensional scaffold has prompted the improvement of this therapeutic strategy. Here we describe a new approach investigating the healing of rabbit cartilage by means of autologous chondrocytes seeded on a biomaterial made of an equine collagen type I-based scaffold. Full-thickness defects were created bilaterally in the weight-bearing surface of the medial femoral condyle of both femora of New Zealand male rabbits. The wounds were then repaired by using both chondrocytes seeded on the biomaterial and biomaterial alone. Controls were similarly treated but received either no treatment or implants of the delivery substance. Histological examination of the reconstructed tissues at 1, 3, 6, and 12 months after transplantation showed that at 1 and 3 months there was no formation of reconstructed tissue in any of the groups evaluated; after 6 months there was evidence of a newly regenerated tissue with some fibrocartilaginous features only in the group treated with biomaterial-seeded cells, and at 12 months a more organized tissue was evident in the same group. With regards to the group transplanted with biomaterial alone and the untreated control group, there was no evidence of new tissue production. These results advocate the use of this collagen-based scaffold for further in vivo studies on large size animals and, finally, in human clinical trials for the treatment of knee cartilage defects.

Animals↗

PubMed2005

Hyaluronic acid hydrogel added with ibuprofen-lysine for the local treatment of chondral lesions in the knee: in vitro and in vivo investigations.

The effect of hyaluronan-based hydrogel with a cross-linking degree of 50% (i.e., the amount of carboxylate groups involved in the cross-lining reaction) (Hyal 50%), loaded with an anti-inflammatory drug (ibuprofen-lysine) for local administration in the osteoarthritic knee was evaluated. The kinetic of drug release from Hyal 50% hydrogel was performed in vitro by a continuous flow system. The release was studied at three different rates (0.375, 0.073, and 0.005 mL/s), and for the slowest one a period of 8 days was necessary to receive the complete release of the drug. A chondral defect was caused in the right femoral medial condyle of 24 rabbits. Twelve animals were treated with Hyal 50%+ibuprofen-lysine and 12 with Hyal 50% by percutaneous injection. The treatments were repeated every 10 days, for three or five times. At 30 and 50 days, no significant differences were observed between the groups (mean score at 30 days: 4.4+/-0.6 in Hyal 50%-treated group and 5.1+/-0.7 in Hyal 50% +Ibuprofen-lysine-treated group; mean score at 50 days: 6.9+/-0.6 in Hyal 50%-treated group and 7.1+/-0.6 in Hyal 50%+ Ibuprofen-lysine-treated group). A significant difference was observed in bone mineral density of the total tibia of rabbits treated by Hyal 50% + Ibuprofen-lysine in comparison with those treated only by Hyal 50%. The positive effects of Hyal 50% on chondral lesions were maintained in the presence of ibuprofen-lysine with the adjunctive effect of an increased limb usage, most likely due to less pain and discomfort.

Animals↗

PubMed2005

Physical characterization of different-roughness titanium surfaces, with and without hydroxyapatite coating, and their effect on human osteoblast-like cells.

The aim of this study was to characterize and compare various titanium (Ti) and hydroxyapatite (HA) coatings on Ti6Al4V, in view of their application on noncemented orthopedic implants. Two innovative vacuum plasma sprayed (VPS) coatings, the first of ultrahigh rough and dense Ti (PG60, Ra=74 microm) and the second of ultrahigh rough and dense Ti coated with HA (HPG60, Ra=52 microm), have been developed, and the response of osteoblast-like cells (MG-63) seeded on these new coatings was evaluated in comparison to: a low roughness and sandblasted (Ti/SA, Ra=4 microm) Ti6Al4V surface; Ti medium (TI01, Ra=18 microm), and high (TI60, Ra=40 microm) roughness VPS coatings; and the relative Ti plus HA duplex coatings (HT01, Ra=12 microm and HT60, Ra=36 microm respectively), also obtained by VPS. PG60 coating presented no open porosity, making it dense and potentially intrinsically stronger. Cell adhesion and proliferation on PG60 was similar to those of the smoothest one (Ti/SA) and adhesion on ultrahigh roughness was lower than the medium- and high-roughness coatings, whereas cell proliferation on PG60 was lower than TI60. The HA coating determined significant increases in cell proliferation at medium and high roughness levels when compared to the relative Ti coating, but not compared to the ultrahigh one; all HA-coated surfaces showed a decrease in alkaline phosphatase activity and collagen I production. Surface morphology and the HA coating strongly affected cell behavior. However, ultrahigh values of roughness are not correctly seen by cells, and the presence of HA has no improving effects.

Biocompatible Materials↗

PubMed2005

Physical and biological characterizations of a novel multiphase anodic spark deposition coating to enhance implant osseointegration.

The present study assessed in vitro the short-term cellular response to surface physico-chemical properties of a new, purposed bioactive surface treatment called BioSpark performed on simply machined and on sand-blasted titanium. Material characterisation was carried out using scanning electron microscopy, energy dispersion spectroscopy, laser profilometry, and thin film X-ray diffraction. The in vitro biological study showed a suitable cellular response with adhesion and spreading level comparable for all the tested specimens. The proliferation analysis demonstrated that all the surfaces successfully supported cellular colonisation; in particular, higher cellular proliferation activity was observed on the BioSpark-treated materials, with values higher than machined titanium. The results suggest that the BioSpark treatment represents a smart way to enhance osteoblastic cellular colonisation and thus improve osteointegration processes of machined and sandblasted titanium for orthopaedic and dental implants.

Bone and Bones↗

PubMed2005

The in vivo behaviour of a sol-gel glass and a glass-ceramic during critical diaphyseal bone defects healing.

The in vivo evaluation, in New Zealand rabbits, of a sol-gel glass 70% CaO-30% SiO2 (in mol%) and a glass-ceramic obtained from thermal treatment of the glass, both bioactive in Kokubo's simulated body fluid (SBF), is presented. Femoral bone diaphyseal critical defects were filled with: (i) sol-gel glass cylinders, (ii) glass-ceramic cylinders, or (iii) no material (control group). Osteosynthesis was done by means of anterior screwed plates with an associate intramedullar Kirschner wire. Each group included 10 mature rabbits, 9 months old. Follow-up was 6 months. After sacrifice, macroscopic study showed healing of bone defects, with bone coating over the cylinders, but without evidence of satisfactory repair in control group. Radiographic study showed good implant stability and periosteal growth and bone remodelling around and over the filled bone defect. The morphometric study showed minimum evidences of degradation or resorption in glass-ceramic cylinders, maintaining its original shape, but sol-gel glass cylinders showed abundant fragmentation and surface resorption. An intimate union of the new-formed bone to both materials was observed. Mechanical study showed the higher results in the glass-ceramic group, whereas sol-gel glass and control group showed no differences. The minimum degradation of glass-ceramic cylinders suggests their application in critical bone defects locations of transmission forces or load bearing. The performance of sol-gel glass cylinders suggests their usefulness in locations where a quick resorption should be preferable, considering the possibility of serving as drug or cells vehicle for both of them.

Animals↗

PubMed2005

Comparative in vitro study on a ultra-high roughness and dense titanium coating.

A new implant surface has been developed with the purpose of avoiding as much stress shielding as possible, and thus prolong the prosthesis lifespan. The aim of this study was to investigate the in vitro effect of this new ultra-high roughness and dense Titanium (Ti) surface (PG60, Ra = 74 microm) in comparison with medium (TI01, Ra = 18 microm) and high (TI60, Ra = 40 microm) roughness and open porous coatings; all the coatings were obtained by vacuum plasma spraying. MG63 osteoblast-like cells were seeded on the tested materials and polystyrene, as control, for 3 and 7 days. Cells proliferated on the material surfaces similarly to the control. Alkaline phosphatase activity had lower values for TI60 than TI01 (p < 0.0005) and PG60 (p < 0.005). Osteocalcin levels measured on TI60 were significantly (p < 0.0005) lower in comparison with TI01 and PG60 at 7 days. Procollagen-I synthesis reduced with increasing roughness and the lowest data was found for PG60. While at 3 days Transforming Growth Factor beta1 levels augmented with increasing roughness, at 7 days TI60, the high roughness surface, was significantly lower than PG60 (p < 0.005) and TI01 (p < 0.001). All tested materials showed significantly higher Interleukin-6 levels than those of polystyrene at both experimental times. Nitric Oxide activity on TI01 was significantly (p < 0.05) higher than on TI60 and polystyrene. In conclusion, the new ultra-high roughness and dense coating PG60 provided a good biological response, even though, at least in vitro, it behaved similarly to the coatings already used in orthopaedics.

Alloys↗

PubMed2005

Tissue healing in implants immediately placed into postextraction sockets: a pilot study in a mini-pig model.

OBJECTIVE: A pilot in vivo study was conducted to evaluate (1) the rate of osseointegration at apical, middle, and coronal levels of oral implants immediately installed into fresh extraction sockets; (2) the maturation of the newly formed bone surrounding implants during 60 days of healing; and (3) the epithelium seal development. STUDY DESIGN: The premolars of 8 male adult mini-pigs were extracted at each mandibular site under general anesthesia. In the experimental side, Frialit-2 implants were immediately inserted. The gap between bone and implants ranged between 3 and 6 mm circumferencially. Bone specimens were obtained at 7, 15, 30, and 60 days after surgery for histologic and histomorphometric studies. Bone-to-implant contact (BIC), bone volume, trabecular thickness, number, and separation were recorded. Nonparametric exact tests were used to evaluate data. RESULTS: BIC at the coronal level was observed close to 0% at day 7 and increased up to 60% at day 60 after surgery on an average. BIC increased from 11.7% to 47.38% at middle level and from 53.4% to 67.38% at apical level from day 7 to day 60. With respect to bone maturation, in the earlier stages of healing, many thin trabeculae were observed, which, particularly at coronal level, became significantly fewer and thicker in more advanced stages. At day 60, the features of the bone were similar to those of baseline. The epithelium never migrated more than 1.8 mm apically to the top of the alveolar bone level. CONCLUSION: When implants are placed immediately into fresh extraction sockets, in minipig models osseointegration also occurs without initial bone contact.

Analysis of Variance↗

PubMed2005

Stromal stem cells and platelet-rich plasma improve bone allograft integration.

Early vascular invasion is a key factor in bone allograft incorporation. It may reduce the complications related to slow and incomplete bone integration. Bone-marrow-derived stromal stem cells associated with platelet-rich plasma are potent angiogenic inducers proven to release vascular endothelial growth factor. Our goal was to test whether the combination of stromal stem cells and platelet-rich plasma is able to increase massive allograft integration in a large animal model with sacrifice at 4 months. A critical defect was made in the mid-diaphysis of the metatarsal bone of 10 sheep; the study group received an allograft plus stromal stem cells, platelet-rich plasma, and collagen (six animals) and the control group received only the allograft (four animals). Investigation was done with radiographs, mechanical tests and histomorphometric analysis, including new vascularization. Results showed substantial new bone formation in the allograft of the study group. Bone formation is correlated with better vascular invasion and remodeling of the graft in the study group. These results confirm the key role played by stromal stem cells and platelet-rich plasma in bone repair. Further studies are needed to better define the role stromal stem cells play when implanted alone.

Animals↗

PubMed2004

Histomorphometric, ultrastructural and microhardness evaluation of the osseointegration of a nanostructured titanium oxide coating by metal-organic chemical vapour deposition: an in vivo study.

Over the past decade the increase of elderly population has determined a rise in the incidence of bone fractures, and the improvement of the implant-bone interface remains an open problem. Metal-organic chemical vapour deposition (MOCVD) has recently been proposed as a technique to coat orthopaedic and dental prostheses with metal nanostructured oxide films either through the decomposition of oxygenated compounds (single-source precursors) or the reaction of oxygen-free metal compounds with oxygenating agents. The present study was performed to assess the in vivo biocompatibility of commercially pure Ti (control material: TI/MA) implants ( psi 2 mm x 5 mm length) coated with nanostructured TiO2 films by MOCVD (Ti/MOCVD) and then inserted into rabbit femoral cortical (middhiaphysis) and cancellous (distal epiphysis) bone. Histomorphometric, ultrastructural and microhardness investigations were carried out. Four and 12 weeks after surgery, significant (p<0.0005) increases in AI of Ti/MOCVD implants were observed as compared to Ti/MA implants (distal femoral epiphysis: 4 weeks=8.2%, ns; 12 weeks=52.3%, p <0.005; femoral diaphysis: 4 weeks=20.2%, p <0.0005; 12 weeks=10.7%, p <0.005). Bone microhardness results showed significant increases for the Ti/MOCVD versus Ti/MA implants at 200 microm in the femoral diaphysis (4 weeks=14.2, p <0.005) and distal femoral epiphysis (12 weeks=14.5, p <0.01) at 4 and 12 weeks, respectively. In conclusion, the current findings demonstrate that the nanostructured TiO2 coating positively affects the osseointegration rate of commercially pure Ti implants and the bone mineralization at the bone-biomaterial interface in both cortical and cancellous bone.

Animals↗

PubMed2003

Effect of trabecular orientation on mechanical resistance and ultrasound propagation in specimens of equine vertebrae.

Osteoporosis involves alterations, not only in density, but also in the architectural organisation of the bone; in particular, trabecular orientation, following the skeletal load directions, lends a high degree of stiffness to the whole bone. We investigated the relationship between trabecular orientation, density, stiffness and ultrasound (US) propagation in two orthogonal directions (par. = parallel to, and ort. = orthogonal to the main orientation of the trabeculae) in cylindrical equine bone specimens (thoracic vertebrae) where a preferential orientation is present. A total of 15 cylinders were progressively decalcified with 0.2 mol/L ethylenediaminetetraacetic acid (EDTA). At different levels of decalcification, we measured the apparent density (g/cm(3)), bone mineral density or BMD (g/cm(2)), stiffness coefficient (MPa) and various US parameters. Before decalcification, stiffness values were the same in all directions. As the decalcification proceeded, the stiffness declined and, at low BMD values, it was significantly different in the two directions, being the highest in the par. one. Different behaviours of US parameters were observed in the two directions: SoS (speed of sound) was closely related to apparent density, BMD and stiffness in the par. direction (r = 0.88, 0.92 and 0.88, respectively, p < 0.0001). In the ort. direction, no significant association has been found between SoS and apparent density, BMD or stiffness. In the same experimental setup, US fast wave amplitude (FWA) was related to apparent density and BMD in the par. direction (r = 0.72 and 0.67, respectively, p < 0.0001) and in the ort. direction (r = 0.83 and r = 0.84 respectively, p < 0.0001). FWA was also correlated to stiffness in both directions (r = 0.61 par.; 0.81 ort., p < 0.0001). These results show that trabecular orientation strongly influences both mechanical properties of bone and US propagation. Furthermore, we found that US parameters can be predictors of mechanical properties of the bone independent of bone density.

Absorptiometry, Photon↗

PubMed2003

Mechanical and histomorphometric evaluations of titanium implants with different surface treatments inserted in sheep cortical bone.

Improvement of the implant-bone interface is still an open problem and the interest in chemical modification of implant surfaces for cementless fixation has grown steadily over the past decade. Mechanical and histomorphometric investigations were performed at different times on implants inserted into sheep femoral cortical bone to compare the in vivo osseointegration of titanium screws ( X 3.5 x 7 mm length) with different surface treatments. After 8 weeks of implantation, the push-out force of anodized and hydrothermally treated implants (ANODIC) was significantly higher than that of machined implants (MACH) (36%, p<0.0005), whereas a decrease of 39% was observed for acid-etched implants (HF) when compared to other surface treatments. After 12 weeks of implantation, the push-out force values of HF implants were still significantly lower than those observed for MACH (-19%, p<0.01) and hydroxyapatite vacuum plasma-sprayed implants (HAVPS, -25%, p<0.0005), and the highest push-out force was found in HAVPS (p<0.001) implants. After 8 and 12 weeks of implantation, the AI of HF implants was significantly (p<0.05) lower ( approximately -25%) than that of MACH, HAVPS and ANODIC implants. In conclusion, results appear to confirm that there are no specific differences between ANODIC and HAVPS implants in terms of behavior. Moreover, although MACH implants show some surface contaminating agents, they appear to ensure good osseointegration within 12 weeks both mechanically and histomorphometrically, as do ANODIC and HAVPS implants. However, further studies are required to investigate bone hardness and mineralization around implants.

Animals↗

PubMed2003

Human osteopenic bone-derived osteoblasts: essential amino acids treatment effects.

The development of in vitro cell culture methods has made it possible to study bone cell metabolism and growth and obtain a deeper insight into the pathophysiology of common orthopedic diseases such as osteoporosis. After analyzing the effect of two essential amino acids, L-arginine (Arg) and L-lysine (Lys), in previous in vitro and in vivo studies, the present authors investigated the administration of Arg and Lys in osteoblasts derived from human osteopenic bone. After isolation, osteoblasts were cultured in DMEM supplemented with either Arg (0.625 mg/ml/day, Arg Group) or Lys (0.587 mg/ml/day, Lys Group), or both of them (Arg-Lys Group), whereas the Control Group was sham-treated. After 7 days the following parameters were tested in all groups: MTT proliferation test, Alkaline Phosphatase (ALP), Nitric Oxide (NO), Calcium (Ca), Phosphorus (P), Osteocalcin (OC), C-Terminal Procollagen type I (PICP), Interleukin-6 (IL-6), Transforming Growth Factor-beta 1 (TGF-beta 1), Platelet Derived Growth Factor (PDGF) and Insulin-Like Growth Factor-I (IGF-I). Results were compared with those obtained from human healthy bone to verify the effect of the amino acids on osteoblasts derived from pathological tissue. In addition, a comparison was also made with the results obtained from rat osteopenic bone to assess reliability of the in vitro model. The current results support previous findings and indicate that Arg and Lys stimulation has a positive effect on osteoblast proliferation, activation and differentiation. Therefore, administration of these amino acids may be useful in clinical treatment and prevention of osteoporosis.

Aged↗

PubMed2003

Osteoblasts cultured from osteoporotic bone: a comparative investigation on human and animal-derived cells.

In vitro studies on pathophysiology and innovative treatments of many orthopaedic diseases, based on the investigations of cells from pathologic skeletal tissues, greatly improve basic knowledge of osteoporosis. Primary osteoblast (OB) cultures derived from osteopenic bone from different species (human, rat, sheep) were compared to assess the differences that should be taken into account when performing in vitro biocompatibiliy tests or investigating pharmacological and physical treatments. Primary OB were isolated from osteopenic patients and animals by well-established methods and their metabolism was assessed with or without 1,25(OH)2D3. The greatest significant differences were observed between rat and human cells both under basal conditions and after 1,25(OH)2D3 stimulation. In addition, the response to 1,25(OH)2D3 stimulation of OBs from osteopenic rats was significantly different from that of human and sheep OB cultures, in terms of NO, OC, IL-6, and TGF-beta1. Cells derived from osteopenic sheep behaved much more similarly to those from humans, except for a significant difference in terms of TGF-beta1 observed both under basal conditions and after stimulation.

Animals↗