PubMed Health⌕ Search

Biomedical subjects

H John Crabtree

Publications and source records attributed to H John Crabtree.

5 recordsLinked to original sources

High fidelity, high yield production of microfluidic devices by hot embossing lithography: rheology and stiction.

We discuss thermoforming of thermoplastic polymers for the hot-embossing lithographic (HEL) fabrication of microfluidic chips near equilibrium conditions that minimize elastic recoil for optimal motif replication. While HEL is often simplistically described as the transfer of micro- and nano-motifs into heat-softened thermoplastic materials, we describe our rational approach to selecting appropriate processing parameters.

Journal Article↗

A rejuvenation method for poly(N,N-dimethylacrylamide)-coated glass microfluidic chips.

As microfluidic chips come to integrate the higher levels of functionality required for the implementation of advanced bioanalytical protocols, a crucial factor is that of cost. Although glass chips provide advantages in multilayer integrations, their cost is far higher than that of polymer chips. However, a simple and effective rejuvenation protocol for glass microchips may enable higher levels of integration and functionality on glass microchips. Here we present a method to rejuvenate glass microchips that had been used for capillary electrophoresis to the extent that their performance was degraded. This degradation was due to one of the two mechanisms: (i) a deterioration of the polymer coating on the inner surface of the microchannel or (ii) an aging of the glass substrate. Using the method presented here, we have rejuvenated more than 50 such "aged" microchips. The performance of these microchips was fully restored after the rejuvenation and lasted for hundreds of DNA separation runs. Our experiments indicate that the loss of resolution in microchip separations was not associated with glass aging, but was due to the degradation of the polymer coating on the inner surface of microchannels. This suggests that it is possible to extend the microchip lifetime "forever" using the rejuvenation protocol and that the exploration of higher levels of integration and functionality on glass microchips (or of hybrid structures involving materials capable of withstanding the reagents and elevated temperatures used) is feasible.

Acrylamides↗

Transition of MEMS technology to nanofabrication.

The transition of MEMS technology to nano fabrication is a solution to the growing demand for smaller and high-density feature sizes in the nanometer scale. Nanoimprint lithography (NIL) techniques for fabricating micro- and nano-features are discussed including hot embossing lithography (HEL), UV Molding (UVM) and micro contact printing (microCP). Recent results in micro and nano-pattern transfer are presented where features ranged from < 100 nm to several centimeters. We also present a comparative study between standard glass microfluidic chips and their HEL counterparts by metrology. Hot-embossed microfluidic chips are shown to be faithful replicates of their parent stamps. NIL is presented as a promising avenue for low-cost, high throughput micro and nano-device fabrication.

Equipment Design↗

Microfabricated device for DNA and RNA amplification by continuous-flow polymerase chain reaction and reverse transcription-polymerase chain reaction with cycle number selection.

We have developed a high-throughput microfabricated, reusable glass chip for the functional integration of reverse transcription (RT) and polymerase chain reaction (PCR) in a continuous-flow mode. The chip allows for selection of the number of amplification cycles. A single microchannel network was etched that defines four distinct zones, one for RT and three for PCR (denaturation, annealing, extension). The zone temperatures were controlled by placing the chip over four heating blocks. Samples and reagents for RT and PCR were pumped continuously through appropriate access holes. Outlet channels were etched after cycles 20, 25, 30, 35, and 40 for product collection. The surface-to-volume ratio for the PCR channel is 57 mm(-1) and the channel depth is 55 microm, both of which allow very rapid heat transfer. As a result, we were able to collect PCR product after 30 amplification cycles in only 6 min. Products were collected in 0.2-mL tubes and analyzed by agarose gel electrophoresis and ethidium bromide staining. We studied DNA and RNA amplification as a function of cycle number. The effect of the number of the initial DNA and RNA input molecules was studied in the range of 2.5 x 10(6) - 1.6 x 10(8) and 6.2 x 10(6) - 2 x 10(8), respectively. Successful amplification of a single-copy gene (beta-globin) from human genomic DNA was carried out. Furthermore, PCR was performed on three samples of DNA of different lengths (each of 2-microL reaction volume) flowing simultaneously in the chip, and the products were collected after various numbers of cycles. Reverse transcription was also carried out on four RNA samples (0.7-microL reaction volume) flowing simultaneously in the chip, followed by PCR amplification. Finally, we have demonstrated the concept of manually pumped injection and transport of the reaction mixture in continuous-flow PCR for the rapid generation of amplification products with minimal instrumentation. To our knowledge, this is the first report of a monolithic microdevice that integrates continuous-flow RT and PCR with cycle number selection.

DNA↗

Improved resolution with microchip-based enhanced field inversion electrophoresis.

We present an improvement of the field inversion electrophoresis (FIE) method in which the passage of sample such as DNA back and forth within a short length of a microchannel can provide a similar resolution to that of a significantly longer microchannel. In constant field FIE the application of an alternating potential (e.g., +/- V) over short periods of time (e.g., several Hz) can provide enhanced separations of DNA fragments. In contrast, the present method consists of a series of separations, each of much longer duration, under high and low fields in such a way that the resolution is enhanced. This method is readily modeled and allows improved resolution to be obtained from extremely short microchannels (e.g., 8 mm) while requiring relatively low applied voltages (e.g., less than 600 V). An additional advantage is that this method can allow for the same equipment to be used in a rapid, low-resolution mode or in a slower, high-resolution mode through what might be referred to as an automated "zoom" capability. We believe that this method may facilitate the integration of microfluidic devices and microelectronic devices by allowing these devices to be of a similar small scale (< 1 cm).

DNA↗