PubMed HealthSearch

Biomedical subjects

H Ukai

Publications and source records attributed to H Ukai.

18 recordsLinked to original sources

Variation in the ratio of respirable particulates over inhalable particulates by type of dust workplace.

OBJECTIVE: The aim of the present study was to clarify the quantitative relationship between respirable particulates and inhalable particulates in various dust workplaces. METHODS: Both respirable particulate and inhalable particulate concentrations were measured in 1644 dust workplaces by means of elutriation, and the ratio of respirable particulate mass over that of inhalable particulate (R/I ratio) was calculated for each workplace. RESULTS: Statistical analyses showed that the R/I ratio varied substantially, depending on the type of dust work. The ratio was highest in welding workplaces (mean +/- SD: 53 +/- 19%) and lowest in foundries (23 +/- 16%); the former value suggests that respirable particulate exposure may be underestimated in substantial parts of welding work when only the occupational exposure limit for inhalable particulates is taken for compliance testing. CONCLUSIONS: Simple compliance with the limit for inhalable particulates is not sufficient, and the limit for respirable particulates should also be simultaneously cleared.

Dust

High-pressure liquid chromatographic determination of toluene in urine as a marker of occupational exposure to toluene.

OBJECTIVE: To establish a convenient method by high-pressure liquid chromatography (HPLC) to measure toluene in urine as a marker of occupational exposure to toluene. METHODS: As soon after sampling as possible, 1 ml of urine was mixed with an equal volume of acetonitrile in a 2.2-ml HPLC glass bottle, and the bottle was tightly sealed and stored at 4 degrees C. Immediately before HPLC determination, 100 microl methanol was added to the mixture to prevent confounding effects of glycosuria, and the bottle was spun to remove any suspended matter. An aliquot of the supernate was introduced into the HPLC system and analyzed on a PRODIGY column, with an acetonitrile - perchloric acid phosphoric acid - water mixture serving as the mobile phase. The effluent was monitored at 191 nm. RESULTS: The method can measure toluene in urine every 20 min, the detection limit was 2 microg/l, the coefficient of variation was less than 5%, and the recovery rate was 100%. No significant reduction in toluene concentration was observed for 1 week after storage at 4 degrees C. When the method was applied to end-of-shift urine samples from 13 male workers exposed to toluene at 18-140 ppm and also to urine samples from 10 nonexposed male controls, toluene in urine was linearly related to toluene exposure concentration, with a regression line passing close to the origin. The correlation coefficient was as high as 0.97 (n=23). No toluene was detected in control urine samples. Calculations suggest that urinary toluene accounts for as little as less than 0.01% of the toluene absorbed via inhalation and that the absorbed toluene is converted almost quantitatively to hippuric acid and, by less than 0.1%, to o-cresol.

Adult

Monitoring of occupational exposure to dichloromethane by diffuse vapor sampling and urinalysis.

OBJECTIVE: The aim of the present study was to develop valid methods for monitoring of occupational exposure to dichloromethane (DCM). METHODS: Carbon cloth as an adsorbent in diffusive sampling was tested for its capacity to adsorb DCM vapor and to retain adsorbed DCM after termination of the exposure. Urine samples collected from DCM-exposed workers were analyzed for DCM by the head-space technique. After extraction with carbon disulfide, DCM in the cloth was analyzed on a DB-WAX capillary column by flame-ionization detection gas chromatography (FID-GC) and DCM in urine was analyzed by electron-capture detection (ECD)-GC. RESULTS: The diffusive sampling with carbon cloth as an adsorbent is applicable to 4-h monitoring of exposure to up to 100 ppm DCM vapor. DCM concentrations detected in end-of-shift urine samples correlated linearly with time-weighted average DCM concentrations measured in the breathing-zone air of the exposed workers; essentially the same exposure-excretion relationship was obtained by vapor monitoring for the afternoon 4-h period as compared with a whole day (8-h) of vapor monitoring. There was no sex difference in the exposure-excretion relation. CONCLUSIONS: Both personal diffusive sampling (at up to 100 ppm DCM and for up to 4 h) and biological exposure monitoring by urinalysis for DCM are applicable in occupational health as reliable measures of exposure to this chlorinated hydrocarbon solvent.

Air Pollutants, Occupational

Endoscopic MRI.

We used a new magnetic resonance endoscope with a small radiofrequent (RF) coil attached to the tip. After insertion of the instrument into the second portion of the duodenum, patients were placed in a magnetic resonance imaging (MRI) scanner. Fast spoiled gradient-recalled acquisition (SPGR) pulse sequences were used for this method. After plain scans, six axial scans were performed after intravenous injection of 20 ml of gadolinium-diethylenetriaminepentaacetic acid (DTPA) contrast medium. We performed endo-MRI on 22 patients, 13 with pancreatic carcinoma, four with pancreatic cystoadenoma, and five with other diseases. In the patients with pancreatic carcinoma, tumors were delineated as low-intensity masses after injection of contrast medium. Dilated main pancreatic ducts were clearly defined. In eight patients with carcinoma of the head of the pancreas, tumors were clearly defined in seven (87.5%) cases. In the eighth case, motion artifact prevented acquisition of a clear image of the pancreas. For diagnosis of invasion of the portal vein, the sensitivity of endo-MRI was 80%, the specificity was 100%, and overall accuracy was 87.5%. The new technique of endo-MRI allows the precise diagnosis of pancreatic tumors.

Carcinoma

ftsE(Ts) affects translocation of K+-pump proteins into the cytoplasmic membrane of Escherichia coli.

The ftsE(Ts) mutation of Escherichia coli causes defects in cell division and cell growth. We expressed alkaline phosphatase (PhoA) fusion proteins of KdpA, Kup, and TrkH, all of which proved functional in vivo as K+ ion pumps, in the mutant cells. During growth at 41 degrees C, these proteins were progressively lost from the membrane fraction. The reduction in the abundance of these proteins inversely correlated with cell growth, but the preformed proteins in the membrane were stable at 41 degrees C, indicating that the molecules synthesized at the permissive temperature were diluted in a growth-dependent manner at a high temperature. Pulse-chase experiments showed that KdpA-PhoA was synthesized, but the synthesized protein did not translocate into the membrane of the ftsE(Ts) cells at 41 degrees C and degraded very rapidly. The loss of KdpA-PhoA from the membrane fractions of ftsE(Ts) cells was suppressed by a multicopy plasmid carrying the ftsE+ gene. While cell growth stopped when the abundance of these proteins decreased 15-fold, the addition of a high concentration of K+ ions specifically alleviated the growth defect of ftsE(Ts) cells but not cell division, and the cells elongated more than 100-fold. We conclude that one of the causes of growth cessation in the ftsE(Ts) mutants is a defect in the translocation of K+-pump proteins into the cytoplasmic membrane.

ATP-Binding Cassette Transporters

[Diagnosis of the wall-thickened lesions of the gallbladder with dynamic MRI].

We studied 32 patients with the thickened lesions of the wall of the gallbladder by using dynamic MRI. We tried the differential diagnosis of gallbladder lesions according to the time intensity curve (TIC) and enhanced pattern. TIC of carcinoma was elevated more seeply from plain to arterial phase than the inflammatory diseases. The Inflammatory diseases were keeping three-layer structures of the wall of the gallbladder, but gallbladder carcinoma destroys the wall-structure. We could diagnose as direct liver invasion of the carcinoma clearly. We could exactly diagnose adenomyomatosis in dynamic MRI by small low intensity spots within the wall of the gallbladder. In the patients with gall stones, the wall of the gallbladder were more clearly observed in dynamic MRI compared with US and EUS.

Carcinoma, Adenosquamous

Surface modifications of titanium in calcium-ion-containing solutions.

The surface of titanium was modified in calcium-ion-containing solutions to improve bone conductivity. Three kinds of aqueous solutions for the modification were prepared using calcium nitrate, calcium chloride, and calcium oxide. The pH values of the solutions were 3.9, 7.4, and 12.6, respectively. At first, anatase powder was immersed in the solutions of 7 days to confirm the effect of the solutions on the modification. As a result, calcium titanate was formed on the anatase powder, indicating that the titanium surface was possibly modified by the solutions. Titanium plates were then immersed in the solutions at ambient temperature for 7 days, washed by deionized water, and dried. X-ray photo-electron spectroscopy of surface-modified titanium revealed that the surface-modified layer contained calcium hydroxide and/or calcium titanate. The surface-modified layer in which titanium was modified was thickest in this order: calcium oxide, calcium chloride, and calcium nitrate solutions. Apatite was formed on the surface-modified titanium in Hanks' solution while apatite was undetected on unmodified titanium. Therefore, the surface modification of titanium may improve bone conductivity. The amount of apatite corresponded to the thickness of the surface-modified layer and the amount of calcium in the layer.

Apatites

Early bone formation around calcium-ion-implanted titanium inserted into rat tibia.

Rat tibia tissue into which calcium ion (Ca2+)-implanted titanium was surgically placed was histologically analyzed to investigate the performance of the Ca(2+)-implanted titanium as a biomaterial. Calcium ions were implanted into only one side of titanium plates at 10(17) ions/cm2 and the Ca(2+)-treated titanium was surgically implanted into rat tibia for 2, 8, and 18 days. Tetracycline and calcein were used as hard-tissue labels. After excision of the tibia, the tissues were fixed, stained, embedded in polymethyl methacrylate, and sliced. The specimens were observed using a fluorescence microscope. A larger amount of new bone was formed on the Ca(2+)-treated side than on the untreated side, even at 2 days after surgery. In addition, part of the bone made contact with the Ca2(+)-treated surface. On the other hand, bone formation on the untreated side was delayed and the bone did not make contact with the surface. Mature bone with bone marrow formed in 8 days. Neither macrophage nor inflammatory cell infiltration was observed. The results indicated that Ca(2+)-implanted titanium is superior to titanium alone for bone conduction.

Animals

Monitoring of occupational exposure to 1-butanol by diffusive sampling and urinalysis.

OBJECTIVES: To investigate the possibility of applying diffusive air sampling and urinalysis (for mother compound and metabolites) to the monitoring of exposure of factory workers to 1-butanol. METHODS: The performance of carbon cloth in adsorbing 1-butanol vapor in air was studied by experimental exposure of the cloth to 1-butanol at 50, 100, 200 or 400 ppm for up to 10 h. 1-Butanol in the exposed cloth was extracted with carbon disulfide and this was followed by gas-chromatographic (GC) analysis. Urine samples were collected from factory workers occupationally exposed to 1-butanol and from rats exposed experimentally to 1-butanol vapour (up to 200 ppm). The urine samples were analyzed by GC without any pretreatment, or after treatment with hydrochloric acid or hydrolase preparation. RESULTS: The performance of the carbon cloth was such that it adsorbed 1-butanol in proportion to the concentration (up to 400 ppm) and the duration (up to 10 h) of exposure, and responded quantitatively to a 15-min exposure up to 400 ppm. The amount of 1-butanol (after enzymic or acid hydrolysis) in post-exposure urine samples from rats was proportional to the exposure intensity. The proportion of free 1-butanol in total 1-butanol (i.e., free+conjugated) in urine was higher after 100 or 200 ppm exposure (35-40%) than after 50 ppm exposure (about 8%). There was a significant increase in total 1-butanol concentration (but not in free 1-butanol) in shift-end urine samples of workers exposed to 1-butanol at concentrations up to 3 ppm. CONCLUSIONS: Diffusive sampling with carbon cloth as an adsorbent can be applied to ambient air monitoring of exposure to 1-butanol. Urinalysis for 1-butanol after hydrolysis is sensitive enough to detect occupational 1-butanol vapour exposure at 3 ppm.

1-Butanol

Types of organic solvents used in small- to medium-scale industries in Japan; a nationwide field survey.

OBJECTIVE: The aim of the present survey is to identify organic solvents commonly used in various workplaces in Japan. METHODS: A total of 24 occupational health service institutions (OHSI) distributed nationwide in Japan offered data on types of solvent workplaces, types of solvents used therein, and the solvent concentrations surveyed in a 2-month period between April and May 1996 to form a data base (OHSI data base, consisting of 1597 cases). Separately, Kyoto Industrial Health Association (KIHA) offered information on 948 cases studied during a 1-year period ranging from April 1995 to March 1996 (KIHA data base). The two data bases were treated in parallel to examine the reproducibility of the results. RESULTS: Detection prevalence was very low (0-1%) for almost half of the 47 legally regulated solvents. Among the solvents in use, toluene was most frequently detected, although the prevalence appeared to be reduced as compared with that recorded for the early 1980s. The most frequently observed solvent combinations comprised toluene, xylenes, and ethyl acetate in the OHSI data base and toluene, xylenes, and methanol in the KIHA data base. Contrary to the case in the 1980s, dichloromethane was used more often than trichloroethylene as a degreasing agent in the present survey. No use was detected for carbon tetrachloride, chloroform, 1,2-dichloroethane, 1,2-dichloroethylene, or 1,1,2,2-tetrachloroethane except for research purposes. CONCLUSIONS: Toluene remained the most common solvent and was used in combination with xylenes, ethyl acetate, and methanol. There was an increase in the use of dichloromethane as a degreasing agent.

Acetates

Diadenosine 5',5'''-P1,P4-tetraphosphate (Ap4A) controls the timing of cell division in Escherichia coli.

BACKGROUND: The timing of the cell division in Escherichia coli is highly regulated, but its mechanism has not been identified. Previously we have found that the cfcA1 mutation uncouples DNA replication and cell division and elevates the frequency of cell division. We further analysed the structure and the role of the cfc genes of cfcA11, a derivative of cfcA1, and another cfc mutant, cfcB1. RESULTS: The cfc mutants divided prior to the ordinary stage of cell division and produced many small cells with nucleoid. However, the cells grew exponentially, and the length of a cell cycle and the initiation mass for chromosome replication were not altered by the cfc mutations. These properties resulted from a reduction of the period between the nucleoid division and the cell division in a cell cycle, and a compensatory lengthening of the period between the cell division and the initiation of the next round of DNA replication. CfcA11 has a mutation in glySa which encodes the alpha-subunit of glycyl-tRNA synthetase, and cfcB1 has an IS2 insertion in apaH which encodes Ap4A hydrolase. The cfc properties of both cfc mutants were suppressed by a multicopy plasmid carrying apaH+, and the intracellular level of Ap4A in cfcA1 was 15-fold higher, and cfcB1 was 100-fold higher than their parent. Experiments using wild-type cells showed that a high level of Ap4A caused early cell division, and that a low level of Ap4A caused delayed cell division. CONCLUSION: Ap4A is a signal for the induction of cell division. High levels of Ap4A are responsible for the initiation of cell division. The glyS mutation permits an efficient synthesis of Ap4A.

Cell Cycle

Exposure of workers to a mixture of toluene and xylenes. II. Effects.

The health effects of exposure to a mixture of toluene and xylene isomers was studied on the fourth or fifth days of a working week in factories in China. The study population comprised 233 subjects (122 men and 111 women), who were exposed to the time weighted geometric mean (maximum) concentrations of toluene (3 (203) ppm) and xylenes (4 (103) ppm). For comparison, 241 non-exposed controls (116 men and 125 women) were recruited from the same regions. The prevalence of some subjective symptoms significantly increased in the exposed population, and the symptom profiles were similar to those found after exposure to toluene or xylenes alone. Haematology and serum biochemistry did not show notable changes. It seems reasonable to conclude that the effects of the toxicities of toluene and xylenes in combination are additive.

Adult

Occupational exposure to solvent mixtures: effects on health and metabolism.

Exposure monitoring by personal diffusive samplers, biological monitoring of toluene exposure by urinary hippuric acid determination, haematology, serum biochemistry for liver function, and a subjective symptom survey by questionnaire were conducted on 303 male solvent workers. They were exposed to a mixture of solvents including toluene (geometric mean 18 ppm), methyl ethyl ketone (MEK; 16 ppm), isopropyl alcohol (IPA; 7 ppm), and ethyl acetate (9 ppm). The intensity was mostly below unity using the additiveness formula based on current Japanese occupational exposure limits, but more than eight times unity at the maximum. The results were compared with the findings in 135 non-exposed male workers of similar ages. Haematology and liver function tests did not show any exposure related abnormality, and subjective symptoms were mostly related to central nervous system depression and local irritation. Further analysis suggested that the irritation effects were not related to exposure to MEK. Analysis of the relation between toluene exposure and hippuric acid excretion in urine showed that there was no metabolic interaction between MEK and toluene, or between IPA and toluene. Overall, therefore, it is concluded that there was no sign or symptom detected to suggest anything other than toluene toxicity, that there was no evidence to indicate any modification of toluene toxicity or metabolism due to coexposure, and that the additiveness assumption is reasonable for risk assessment for the combination of solvents under these exposure conditions.

1-Propanol

Dose-dependent increase in subjective symptoms among toluene-exposed workers.

A factory survey on dose-response relationship in toluene toxicity was conducted in 1985-1989 in four cities in China. The examination items consisted of personal diffusive sampling for TWA exposure measurement, questionnaires on subjective symptoms, hematology and serum biochemistry, and clinical examination including simple neurology tests. Hippuric acid was also determined in urine samples collected at the end of the shift. With selection criteria that (1) complete results were available on all study items and (2) valid toluene exposure data (i.e., toluene shared 90% or more of the exposure) were obtained for the exposed, 452 toluene-exposed workers (206 men and 246 women; toluene exposure at 24.7 ppm as GM) and 517 nonexposed controls (246 men and 271 women) were selected. The subjective symptoms increased in close association with the intensity of exposure to toluene; the threshold concentration appeared to exist at 100 ppm in the case of symptoms during work, and it might be at 50-100 ppm when symptoms off work were evaluated. During the work with exposure at higher concentrations, various symptoms possibly related to CNS or local effects (e.g., eyes, nose, and throat) were complained, and dizziness and floating sensations were identified as typical symptoms with significant dose-response relationship. Several symptoms persisted off work, most of which were apparently related but not necessarily limited to CNS effects. Hematology and serum biochemistry were essentially negative.

Adolescent

Symptoms and signs in workers exposed predominantly to xylenes.

Surveys were conducted in factories in China where workers were engaged in the production of rubber boots or plastic-coated wire or in printing work, and were exposed to xylene vapors. Based on the data on exposure as monitored by personal diffusive sampling, 175 xylene-exposed workers (107 men and 68 women) were selected as those (1) who underwent all examinations and (2) for whom the sum of the three xylene isomers accounted for 70% or more of the total exposure (on a ppm basis). The intensity of exposure was such that the sum of the three isomer concentrations was 14 ppm as a geometric mean and 21 ppm as an arithmetic mean. As controls, 241 nonexposed workers (116 men and 125 women) were recruited either from the same factories or from factories in the same regions. There was an increased prevalence of subjective symptoms in the exposed workers which were apparently related to the effects on the central nervous system and to the local effects on the eyes, the nose, and the throat, although dose-dependency of the symptoms was evident in only a limited number of cases, possibly because the intensity of exposure was rather low. It was further observed that the findings of hematology and serum biochemistry in respect of liver and kidney functions were generally negative, showing that xylenes are not toxic to the hematopoietic organs, the liver, or the kidney.

Adult

Relationship between exposure and environmental concentrations in organic solvent workplaces.

The correlation between the exposure concentration (ExpC) of workers and the environmental concentration (EnvC) in their workplaces were examined in 143 printing, painting, gluing, degreasing and other solvent workplaces manned by 535 workers of both sexes. ExpC was measured with carbon felt dosimeters, and EnvC was with grab sampling of air into poly-tetrafluoroethylene bags; both were followed by GC analyses. When ExpC and EnvC were compared on both group and individual basis, the correlation was found to be positive but rather weak, and individual difference in ExpC within the workers of the same workplace was not negligible. Workplaces were classified after regulatory practice into three categories, and attempts were made to find out the conditions so that none among the 174 workers in the 43 Category 1 (i.e., "clean" from regulatory view point) workplaces would be exposed to solvent vapors over the current occupational exposure limit (OEL). Accordingly, it was found that the requirement will be met in case half the OEL is taken as the E value (the EnvC limit set by the regulation). Thus, the same conclusion was reached through the analyses of two separate batches of experiences, i.e., one in the present study and the other in the previous report (Ikeda and Ohtsuki 1985).

Environmental Exposure