Biomedical subjects

H Y Göksu

Publications and source records attributed to H Y Göksu.

17 recordsLinked to original sources

PubMed2006

Luminescence dosimetry using building materials and personal objects.

There is a growing public awareness of the risk of accidental radiation exposure due to ageing nuclear power installations, illegal dumping of nuclear waste and terrorist activities, and of the consequential health risks to populations in addition to social and economic disturbance extending beyond national boundaries. In the event of catastrophic incidents where no direct radiation monitoring data are available, the application of retrospective dosimetry techniques such as luminescence may be employed with materials from the immediate environment to confirm values of cumulative gamma dose to compare with or augment computational modeling calculations. Application of the method to post-Chernobyl studies has resulted in the development of new procedures using fired building materials with the capability to measure cumulative doses owing to artificial sources of gamma radiation as low as 20 mGy. Combined with Monte Carlo simulations of photon transport, values of cumulative dose in brick can be presented in a form suitable for use in dose-reconstruction efforts. Recent investigations have also shown that certain types of cementitious building material, including concrete, mortar and plaster, and personal objects in the form of telephone cards containing microchips and dental ceramics have the potential to be used for retrospective dosimetry. Examples of the most recent research concerning new materials and examples of application to sites in the Former Soviet Union are discussed.

Construction Materials↗

PubMed2006

On the relationship between dose-, energy- and LET-response of thermoluminescent detectors.

Measurements of the response of thermoluminescent (TL) detectors after gamma ray doses high enough to observe signal saturation provide input to microdosimetric models which relate this gamma-ray response with the energy response after low doses of photons (gamma rays and low-energy X rays) and after high-LET irradiation. To measure their gamma ray response up to saturation, LiF:Mg,Ti (MTS-7 and MTT), LiF:Mg,Cu,P (MCP-7), CaSO4:Dy (KCD) and Al2O3:C detectors were irradiated with 60Co gamma rays over the range 1-5000 Gy. The X-ray photon energy response and TL efficiency (relative to gamma rays) after doses of beta rays and alpha particles, were also measured, for CaSO4:Dy and for Al2O3:C. Microdosimetric and track structure modelling was then applied to the experimental data. In a manner similar to LiF:Mg,Cu,P, the experimentally observed under response of alpha-Al2O3:C to X rays <100 keV, compared with cross-section calculations, is explained as a microdosimetric effect caused by the saturation of response of this detector without prior supralinearity (saturation of traps along the tracks). The enhanced X-ray photon energy response of CaSO4:Dy is related to the supralinearity observed in this material after high gamma ray doses, similarly to that in LiF:Mg,Ti. The discussed model approaches support the general rule relating dose-, energy- and ionisation density-responses in TL detectors: if their gamma ray response is sublinear prior to saturation, the measured photon energy response is lower, and if it is supralinear, it may be higher than that expected from the calculation of the interaction cross sections alone. Since similar rules have been found to apply to other solid-state detector systems, microdosimetry may offer a valuable contribution to solid-state dosimetry even prior to mechanistic explanations of physical phenomena in different TL detectors.

Computer Simulation↗

PubMed2006

The use of alpha-Al2O3:C in Risø OSL single grains attachment system for assessing the spatial dose rate distribution due to incorporation of 90Sr in human teeth.

The possibility of using a single grain OSL attachment system developed by the Risø National Laboratory (Roskilde, Denmark) for assessing the spatial distribution of radionuclides incorporated in human tissues was investigated. Detectors containing arrays of single grains of alpha-Al2O3)C powder (Landauer Inc., USA) were prepared using aluminium discs (diameter 9.7 mm), which can accommodate 100 single grains in 0.3 mm holes positioned in a 10 x 10 grid. The luminescence and dosimetric properties of each grain were investigated by exposing the detectors to uniform photon radiation fields. After the characterisation of the detectors, the systems were tested to assess the spatial dose rate distribution because of 90Sr incorporated in a tooth sample extracted from an inhabitant of the Techa River region.

Aluminum Oxide↗

PubMed2006

Cumulative dose assessment using thermoluminescence properties of porcelain isolators as evidence of a severe radiation accident in the Republic of Sakha (Yakutia), Russia, 1978.

The cumulated absorbed doses in four electric porcelain isolators collected at the site of the "Kraton-3" underground nuclear explosion in the Republic of Sakha (Yakutia), Russia, were evaluated using the thermoluminescence technique. The doses attributable to the accidental radioactive release from the explosion ranged from 1.2 to 10 Gy; the maximal value was detected for the isolator collected near the "Kraton-3" borehole. The measured thermoluminescence doses for two of the four samples analyzed are in reasonable agreement with the estimates of external gamma dose presented by earlier investigators of the site.

Dental Porcelain↗

PubMed2005

Limits of thermoluminescence dosimetry using quartz extracted from recent building materials in urban settlements.

The luminescence of quartz extracted from recently fired building material is known to detect doses of few mGy and can be successfully employed in the case of large scale radiation exposures due to nuclear accidents or terrorist acts. One brick and two tiles (50-80 years range) collected from an urban settlement were used to test the realistic minimum detectable dose limits of retrospective luminescence dosimetry. Independent methods like alpha counting, beta dosimetry, gamma spectrometry and flame photometry were used for the annual dose assessment. Two approaches were employed for the evaluation of the total accrued dose: regenerative dose and additive dose. The former allows the assessment of doses due to anthropogenic sources of radiation as low as approximately 12 mGy by using 10-year-old samples, but it can be applied only in samples showing no sensitisation. The latter can be applied to any sample, however, the related uncertainty is higher and minimum detectable anthropogenic dose in young samples amounts to 20 mGy.

Cities↗

PubMed2005

Retrospective luminescence dosimetry: development of approaches to application in populated areas downwind of the Chernobyl NPP.

The cumulative absorbed dose in fired-clay bricks collected from ten buildings in the populated contaminated settlement (137Cs, 1,470 kBq m(-2)) of Stary Vishkov, located 175 km downwind of the Chernobyl Nuclear Power Plant (NPP) in the Bryansk administrative region of Russia, was determined using luminescence techniques by five laboratories. At each location, the cumulative dose, after subtraction of the natural background dose, was translated to absorbed dose in air using conversion factors derived from Monte Carlo simulations. The simulations employed source distributions inferred from contemporary soil contamination data and also took into account heterogeneity of fallout deposition. At four locations the cumulative dose at a reference location was calculated, enabling the luminescence determinations to be compared directly with values of cumulative absorbed dose in air obtained using deterministic models. A "local" conversion factor was also derived from the Monte Carlo simulations for locations where the disturbance of soil was significant. Values of the "local" cumulative dose in air calculated using this factor were compared with those predicted using the deterministic models at each sampled location, allowing location factors to be calculated. The methodology developed is generally applicable to populated areas contaminated by radioactive fallout in which brick buildings are found. The sensitivity of the luminescence techniques for bricks from this region of Russia was sufficient to evaluate cumulative absorbed dose in brick due to fallout of less than 20 mGy.

Air Pollutants, Radioactive↗

PubMed2005

Assessment of 90Sr concentration in dental tissue using thin-layer beta-particle detectors and verification with numerical calculations.

Electron paramagnetic resonance (EPR) measurements of tooth enamel can be used as an individual biological dosimeter for external dose assessment. However, the presence of 90Sr in the tooth tissues makes the task of interpreting EPR tooth dosimetry more complicated. The determination of the dose contribution of incorporated 90Sr in calcified tissue to the total dose measured by EPR is one of the main aspects of correct interpretation of EPR tooth dosimetry. In this work, experimental and numerical calculations were performed to convert the measured beta-particle dose rate to 90Sr concentration in calcified tissue. The cumulative beta-particle dose was measured by exposing artificially contaminated dentin and enamel to thin-layer alpha-Al2O3:C detectors in two different exposure geometries. Numerical calculations were performed for experimental exposure conditions using calculations of electron transport and secondary photons [Monte Carlo n-Particle Transport code version 4C2 (MCNP)]. Numerical calculations were performed to optimize the sample size and exposure geometry. The applicability of two different exposure conditions to be used in routine analysis was tested. Comparison of the computational and experimental results demonstrated very good agreement.

Beta Particles↗

PubMed2004

Isothermal decay studies of intermediate energy levels in quartz.

The recent interest in the thermoluminescence of quartz extracted from unfired building materials, such as mortar and concrete for dose reconstruction applications, led to the requirement of an accurate determination of the lifetime of the intermediate glow peaks in this mineral. The prediction of the lifetimes of these peaks is helpful in establishing the likely time range within which retrospective measurements can be carried out. These peaks, corresponding to intermediate energy levels, occur in the glow curve in the temperature range 150-250 degrees C (heating rate 2 degrees C/s). Lifetimes of 720+/-70 days and 580+/-70 years (at a temperature of 15 degrees C) were derived for the two main peaks placed in the glow curve at approximately 150 degrees C and 200 degrees C, respectively, using the isothermal decay technique. These results as well as the estimated values of the trap parameters (thermal activation energy and frequency factor) have been compared with the data already available in the literature.

Construction Materials↗

PubMed2004

Thermoluminescence dosimetric properties of a new thin beta detector (LiF:Mg, Cu, P; GR-200F) in comparison with highly sensitive Al2O3:C beta dosimeters.

There is an increasing need for efficient beta detectors to fulfil ICRU recommendations for new quantities especially in the field of medical physics and retrospective dosimetry. The thermoluminescence properties of thin LiF:Mg, Cu, P (GR-200F) tapes produced in 1998 by Sange Company, People's Republic of China, are investigated and compared with those of highly sensitive thin Al2O3:C beta detectors as regards their applicability in the detection of low energy photons and beta particles. The radiation dose response, minimum detectable dose, reproducibility of measurements and effect of residual signal at low dose are assessed for the possible low level beta dosimetry use. The radiation dose response and photon and beta detection efficiencies are tested underpractical laboratory conditions. The effects of indoor fluorescent light and residual signal after the first read-out are investigated with a view to optimising handling conditions such as post-irradiation and pre-heating treatments for routine dosimetry. The photon energy responses of the detectors are investigated using 150 keV filtered x-rays and 60Co gamma-rays.

Aluminum Oxide↗

PubMed2004

Comparison of retrospective luminescence dosimetry with computational modeling in two highly contaminated settlements downwind of the Chernobyl NPP.

The cumulative absorbed dose in bricks collected from six buildings in two heavily contaminated settlements (137Cs > 2,000 kBq m(-2)) located downwind of the Chernobyl Nuclear Power Plant was determined using luminescence techniques by six laboratories. The settlements, Vesnianoje in Ukraine and Zaborie in Russia, are located in, respectively, proximal and distal locations relative to the Chernobyl Nuclear Power Plant. The luminescence determinations of cumulative dose in brick, after subtraction of the natural background dose, were translated to absorbed dose in air at a Reference Location using conversion factors derived from Monte Carlo simulations of photon transport. The simulations employed source distributions inferred from contemporary soil contamination data and also took into account heterogeneity of fallout deposition. This translation enables the luminescence determinations to be compared directly with values of cumulative absorbed dose obtained by computational modeling and also other dose reconstruction methods. For each sampled location the cumulative dose was calculated using three deterministic models, two of which are based on the attenuation of dose-rate with migration of radionuclides in soil and the third on historic instrumental gamma dose-rate data. The results of the comparison of the two methods indicate overall agreement within margins of +/-25%. The methodology developed is generally applicable and adaptable to areas contaminated by much lower levels of radioactive fallout in which brick buildings are found.

Computer Simulation↗

PubMed2004

The application of retrospective luminescence dosimetry in areas affected by fallout from the semipalatinsk nuclear test site: an evaluation of potential.

Luminescence retrospective dosimetry techniques have been applied with ceramic bricks to determine the cumulative external gamma dose due to fallout, primarily from the 1949 test, in populated regions lying NE of the Semipalatinsk Nuclear Test Site in Altai, Russia, and the Semipalatinsk region, Kazakhstan. As part of a pilot study, nine settlements were examined, three within the regions of highest predicted dose (Dolon in Kazakshstan; Laptev Log and Leshoz Topolinskiy in Russia) and the remainder of lower predicted dose (Akkol, Bolshaya Vladimrovka, Kanonerka, and Izvestka in Kazakshstan; Rubtsovsk and Kuria in Russia) within the lateral regions of the fallout trace due to the 1949 test. The settlement of Kainar, mainly affected by the 24 September 1951 nuclear test, was also examined. The bricks from this region were found to be generally suitable for use with the luminescence method. Estimates of cumulative absorbed dose in air due to fallout for Dolon and Kanonerka in Kazakshstan and Leshoz Topolinskiy were 475 +/- 110 mGy, 240 +/- 60 mGy, and 230 +/- 70 mGy, respectively. The result obtained in Dolon village is in agreement with published calculated estimates of dose normalized to Cs concentration in soil. At all the other locations (except Kainar) the experimental values of cumulative absorbed dose obtained indicated no significant dose due to fallout that could be detected within a margin of about 25 mGy. The results demonstrate the potential suitability of the luminescence method to map variations in cumulative dose within the relatively narrow corridor of fallout distribution from the 1949 test. Such work is needed to provide the basis for accurate dose reconstruction in settlements since the predominance of short-lived radionuclides in the fallout and a high degree of heterogeneity in the distribution of fallout are problematic for the application of conventional dosimetry techniques.

Luminescent Measurements↗

PubMed2002

Thin layer alpha-Al2O3:C beta dosemeters for the assessment of current dose rate in teeth due to 90Sr intake, and comparison with electron paramagnetic resonance dosimetry.

The use of thin-layer alpha-Al2O3:C thermoluminescent detectors (TLDs) for the assessment of current beta dose rate in human teeth due to 90Sr intake is investigated. The teeth used in this study were collected from members of the Techa river population who were exposed to radiation as a result of releases of the Mayak plutonium production facilities (Southern Urals-Russia) between 1949 and 1956. The beta dose rates from different parts of the tooth (enamel, crown dentine, and root) were determined by storing the detectors over the samples in a shielded environment. The cumulative dose measured by electron paramagnetic resonance (EPR) in different dental tissues is found to be proportional to current dose rate obtained from alpha-Al2O3:C thermoluminescence dosemeters. The retention of 90Sr in various parts of the teeth is discussed.

Aluminum Oxide↗

PubMed2002

First international intercomparison of luminescence techniques using samples from the Techa River Valley.

Bricks collected from a contaminated village (Muslyumovo) of the lower Techa river valley, Southern Urals, Russia, were measured using thermoluminescence and optically stimulated luminescence by four European laboratories and a U.S. laboratory to establish and compare the applied dose reconstruction methodologies. The bricks, collected from 60-100-year-old buildings, had accumulated a relatively high dose due to natural sources of radiation in the brick and from the surrounding environment. This work represents the results of a first international intercomparison of luminescence measurements for bricks from the Southern Urals. The luminescence measurements of absorbed dose in bricks collected from the most shielded locations of the same buildings were used to determine the background dose due to natural sources of radiation and to validate the age of the bricks. The absorbed dose in different bricks measured by four laboratories using thermoluminescence and optically stimulated luminescence at a depth of 10 +/- 2.5 mm from the exposed brick surface agreed within +/-21%. After subtraction of the natural background dose, the absorbed dose in brick due to contaminated river sediments and banks was calculated and found to range between 150 and 200 mGy. The cumulative doses in brick due to man-made sources of radiation at 100 and 130 mm depths in the bricks were also measured and found to be consistent with depth dose profiles calculated by Monte Carlo simulations of photon transport for possible source distributions.

Background Radiation↗

PubMed2002

Elevated exposure rates under inclined birch trees indicate the occurrence of rainfall during radioactive fallout from Chernobyl.

Knowledge of the mode of deposition (wet or dry) during the main fallout period following the Chernobyl accident in late April 1986 is one of the most important parameters in environmental reconstruction of the radiation dose to the thyroid from 113I following the accident. Meteorological data are available only for a small number of locations, but routine field measurements in 1997 of exposure rates in areas still contaminated by 137Cs revealed that there is a natural indicator of wet deposition. Follow-up measurements confirmed that there is a significant difference in exposure rates measured on different sides at the bases of inclined birch trees in areas of wet deposition. In such areas, the exposure rates measured on the "sheltered" sides of the trees were on average 2.3+/-0.2 times those measured on the unsheltered side. In areas of dry deposition the comparable ratio was 1.01+/-0.02 for similarly inclined trees. Because birch trees are a common feature in the contaminated territories, this effect has a wide potential for use in determining whether the fallout in many areas was due to wet or dry deposition.

Environmental Exposure↗

PubMed2000

Thermoluminescence dating of terrazzo from the monastery church of Tegernsee (Bavaria, Germany) using the 210 degrees C TL peak of quartz.

Thermoluminescence (TL) is one of the most important physical methods used in archaeometry for dating ceramics. In this study the newly developed procedures based on the use of the 210 degrees C TL peak of quartz were applied to well-dated bricks of the church of the Tegernsee monastery in Bavaria. The resulting TL ages obtained from these well-dated bricks were used as a reference for selection of the suitable measurement procedure and to test the precision of the measurements and the accuracy of the technique. The optimized procedure was applied to the terrazzo fragments from the monastery church. The TL results provide a new understanding of the architectural history of the church. The improved measurement procedure including various dose evaluation techniques and the components of the annual dose assessment are described.

Archaeology↗

PubMed1998

Issues in the reconstruction of environmental doses on the basis of thermoluminescence measurements in the Techa riverside.

The potential of thermoluminescence measurements of bricks from the contaminated area of the Techa river valley, Southern Urals, Russia, for reconstructing external exposures of affected population groups has been studied. Thermoluminescence dating of background samples was used to evaluate the age of old buildings available on the river banks. The anthropogenic gamma dose accrued in exposed samples is determined by subtracting the natural radiation background dose for the corresponding age from the accumulated dose measured by thermoluminescence. For a site in the upper Techa river region, where the levels of external exposures were extremely high, the depth-dose distribution in bricks and the dependence of accidental dose on the height of the sampling position were determined. For the same site, Monte Carlo simulations of radiation transport were performed for different source configurations corresponding to the situation before and after the construction of a reservoir on the river and evacuation of the population in 1956. A comparison of the results provides an understanding of the features of the measured depth-dose distributions and height dependencies in terms of the source configurations and shows that bricks from the higher sampling positions are likely to have accrued a larger fraction of anthropogenic dose from the time before the construction of the reservoir. The applicability of the thermoluminescent dosimetry method to environmental dose reconstruction in the middle Techa region, where the external exposure was relatively low, was also investigated.

Alpha Particles↗

PubMed1996

Depth-dose distribution in bricks determined by thermoluminescence and by Monte-Carlo calculation for external gamma-dose reconstruction.

The analysis of depth-dose distributions in bricks sampled from walls in areas with nuclear waste or accident contamination has the potential of providing information on the energy and source configuration of the gamma-radiation that had been incident on the brick. In this study, a brick from a mill facing a shallow water reservoir of the contaminated Techa river in the South Ural region is investigated. Thermoluminescence (TL) methods were used to measure the accumulated dose at several depths in the brick. The accidental external gamma-dose is obtained by subtracting the natural radiation background dose from the total accumulated dose. In the first segment of the brick, at a depth of about 1.5 cm, the accident dose was found to be roughly 3.5 Gy. Monte-Carlo simulations of the photon transport from the reservoir bed contaminated with 137Cs were calculated for different depths in the brick. The calculations were made assuming different attenuating water levels. It is found that the depth-dose distribution determined by measurements corresponds to a water level between 20 and 50 cm. The results indicate that TL measurements combined with Monte-Carlo modelling calculations are highly promising for external gamma-dose reconstruction applications.

Beta Particles↗