Biomedical subjects

Huipin Yuan

Publications and source records attributed to Huipin Yuan.

6 recordsLinked to original sources

PubMed2006

Relevance of osteoinductive biomaterials in critical-sized orthotopic defect.

Several publications have shown the phenomenon of osteoinduction by biomaterials to be real. However, whether the ability of a biomaterial to initiate bone formation in ectopic implantation sites improves the performance of such osteoinductive biomaterial in clinically relevant orthotopic sites remains unclear. No studies have been published in which osteoinductive potential of a biomaterial is directly related to its performance orthotopically. In this study, we compared osteoinductive and nonosteoinductive biphasic calcium-phosphate (BCP) ceramics ectopically and in a clinically relevant critical-sized orthotopic defect in goats. The two materials, BCP1150 and BCP1300, had similar chemical compositions, crystallinities, and macrostructures, but their microstructures differed significantly. BCP1150, sintered at a lower temperature, had a large amount of micropores, small average crystal size, and hence a high specific surface area. In contrast, BCP1300, with few micropores, had a significantly lower specific surface area as compared to BCP1150. Twelve-week intramuscular implantation in goats (n = 10) showed that bone was induced in all BCP1150 implants, while no signs of bone formation were found in any of the BCP1300 implants. After 12 weeks of implantation in a bilateral critical-sized iliac wing defect in the same goats, BCP1150 showed significantly more bone than BCP1300. In addition, the analysis of fluorochrome markers, which were administered to the animals 4, 6, and 8 weeks after implantation to follow the bone growth dynamics, showed an earlier start of bone formation in BCP1150 as compared to BCP1300. Significantly better performance of an osteoinductive ceramic in a critical-sized orthotopic defect in a large animal model in comparison to a nonosteoinductive ceramic suggests osteoinduction to be clinically relevant. Further improvement of material osteoinductive properties is thus a significant step forward in the search for alternatives for autologous bone graft.

Animals↗

PubMed2006

Cross-species comparison of ectopic bone formation in biphasic calcium phosphate (BCP) and hydroxyapatite (HA) scaffolds.

Material-induced bone formation reported in canine, bovid, suid, and primate species does not often occur in lagomorph or rodent models. In this study, we test biphasic calcium phosphate and hydroxyapatite- induced bone formation in subcutaneous pockets of mice and intramuscular pockets in rats, rabbits, and dogs. All scaffolds are of similar size, and all animals were sacrificed at 90 days post-implantation. In dogs (N = 8), all implants showed bone formation with significantly more bone formed in biphasic calcium phosphates (30 +/- 6%, N = 8) as compared to hydroxyapatite (14 +/- 5%, N = 8) (p = 0.003). Hydroxyapatite implants did not induce bone formation in mice, rats, or rabbits. Biphasic calcium phosphate induced bone in 6 of 8 scaffolds implanted in 4 rabbits and 3 of 16 scaffolds implanted in 16 mice, whereas it did not induce bone formation in any of the 8 rats. The results presented herein suggest that the incidence of material-induced bone formation varies with animal species and is related to the implant material used.

Animals↗

PubMed2005

3D microenvironment as essential element for osteoinduction by biomaterials.

In order to unravel the mechanism of osteoinduction by biomaterials, in this study we investigated the influence of the specific surface area on osteoinductive properties of two types of calcium phosphate ceramics. Different surface areas of the ceramics were obtained by varying their sintering temperatures. Hydroxyapatite (HA) ceramic was sintered at 1150 and 1250 degrees C. Biphasic calcium phosphate (BCP) ceramic, consisting of HA and beta-tricalcium phosphate (beta-TCP), was sintered at 1100, 1150 and 1200 degrees C. Changes in sintering temperature did not influence the chemistry of the ceramics; HA remained pure after sintering at different temperatures and the weight ratio of HA and beta-TCP in the BCP was independent of the temperature as well. Similarly, macroporosity of the ceramics was unaffected by the changes of the sintering temperature. However, microporosity (pore diameter <10 microm) significantly decreased with increasing sintering temperature. In addition to the decrease of the microporosity, the crystal size increased with increasing sintering temperature. These two effects resulted in a significant decrease of the specific surface area of the ceramics with increasing sintering temperatures. Samples of HA1150, HA1250, BCP1100, BCP1150 and BCP1200 were implanted in the back muscles of Dutch milk goats and harvested at 6 and 12 weeks post implantation. After explantation, histomorphometrical analysis was performed on all implants. All implanted materials except HA1250 induced bone. However, large variations in the amounts of induced bone were observed between different materials and between individual animals. Histomorphometrical results showed that the presence of micropores within macropore walls is necessary to make a material osteoinductive. We postulate that introduction of microporosity within macropores, and consequent increase of the specific surface area, affects the interface dynamics of the ceramic in such a way that relevant cells are triggered to differentiate into the osteogenic lineage.

Animals↗

PubMed2004

Optimization of bone tissue engineering in goats: a peroperative seeding method using cryopreserved cells and localized bone formation in calcium phosphate scaffolds.

BACKGROUND: Bone tissue engineering by combining cultured bone marrow stromal cells with a porous scaffold is a promising alternative for the autologous bone graft. Drawbacks of the technique include the delay necessary for cell culture and the complicated logistics. We investigated methods to bypass these drawbacks. Furthermore, we investigated the localization of bone formation inside the scaffold. METHODS: Bone marrow stromal cells from seven goats were culture expanded and cryopreserved. One week before surgery, some of the cells were thawed, cultured, and seeded on porous calcium phosphate scaffolds. The constructs were cultured for another week until implantation. The remaining cryopreserved cells were thawed just before implantation and peroperatively resuspended in plasma before combining with the scaffold. Scaffolds impregnated with fresh bone marrow, devitalized cultured constructs, and empty scaffolds served as controls. All samples were implanted in the back muscles of the goats for 9 weeks. RESULTS: Histologic examination showed minimal (<1%) bone in the empty and devitalized scaffolds, 4.2 +/- 5.1 bone area percent in the bone marrow samples, and significantly more bone in both the cultured and peroperatively seeded constructs (11.7 +/- 2.5 and 14.0 +/- 2.0%). The peripheral 350 microm of the implants contained significantly less bone. CONCLUSION: Peroperative preparation of osteogenic constructs with cryopreserved cells is feasible. These constructs yield substantially more bone than the scaffolds alone or scaffolds impregnated with fresh bone marrow. Bone deposition is much less on the scaffold periphery.

Animals↗

PubMed2004

Bone tissue engineering in a critical size defect compared to ectopic implantations in the goat.

Since the application of the autologous bone graft, the need for an alternative has been recognized. Tissue engineering (TE) of bone by combining bone marrow stromal cells (BMSCs) with a porous scaffold, is considered a promising technique. In this study we investigated the potential of tissue engineered bone to heal a critical sized defect in the goat. Orthotopic bone formation was compared to ectopic bone formation in comparable constructs. TE constructs were prepared from goat BMSCs and porous biphasic calcium phosphate ceramic scaffolds. These constructs and scaffolds without cells were implanted paired in critical sized iliac wing defects. Comparable samples were implanted intramuscularly. After 9 (n=7) and 12 (n=8) weeks implantation, the samples were analyzed histomorphometrically. After 9-weeks implantation in the iliac wing defect, significantly more bone apposition was found in the TE condition. After 12 weeks, the defects were almost completely filled with bone, but no significant advantage of TE was determined anymore. This contrasted with the intramuscular samples where TE implants showed significantly more bone at both time points. In conclusion, bone TE is feasible in critical sized defects. However, when appropriate osteoconductive/inductive materials are applied the effect of cell seeding may be temporary.

Animals↗

PubMed2002

A comparison of the osteoinductive potential of two calcium phosphate ceramics implanted intramuscularly in goats.

The osteoinductive potential, or bone induction potency, of two calcium phosphate ceramics was evaluated after intramuscular implantation in goats. The ceramics were comprised of hydroxyapatite (HA) and biphasic calcium phosphate (BCP), the later of which contained a 85/15 mixture of hydroxyapatite and tricalcium phosphate (TCP). Both ceramics had a similar macroporosity of around 55% and a pore distribution between 100 and 800 microm. Besides the difference in chemistry, BCP was also microporous and hence had a different surface microstructure. After implantation in the back muscles of four goats for 12 weeks, all 8 BCP samples (7x7x7 mm(3)) showed the presence of bone formation in the macropores (1+/-1%), while no bone was found in any of the HA samples. The used BCP can therefore be characterized as an osteoinductive material. Having the ability to induce bone formation in soft tissues, the BCP presented herein may be a useful biomaterial for bone repair when combined with cultured osteogenic cells, growth factors or both.

Journal Article↗