PubMed Health⌕ Search

Biomedical subjects

I C du Preez

Publications and source records attributed to I C du Preez.

15 recordsLinked to original sources
PubMed2006

Self-etching bonding systems: in-vitro shear bond strength evaluation.

The purpose of this in vitro study was to compare the dentine shear bond strength of five self-etching bonding agents with that of a total-etch dentine bonding agent (used as control). Sixty recently extracted third molar teeth were mounted in acrylic resin and the occlusal surfaces ground to expose superficial dentine. A standardised smear layer was created by polishing with wet 600-grit SiC paper. Products evaluated were Xeno III (XIII), Clearfil SE Bond (SE), ABF (ABF), Optibond Solo Self-etch (OS), Adper Prompt-L-Pop (PLP) and the control, Scotchbond Multipurpose Plus (SBMP). Resin stubs were bonded to the dentine using the bonding agents according to manufacturer's instructions. Composite stubs were manufactured using an Ultradent jig and two increments of Z100, A1 shade composite. The bonds were subsequently stressed to failure with an Instron testing machine, operating at a crosshead speed of 0.5 mm/min. The data was statistically analysed using ANOVA (alpha < or = 0.05). The mean SBS (MPa) were: SBMP (Control) = 24.1 +/- 7.6; XIII = 17.3 +/- 4.1; SE = 26.2 +/- 7.8; ABF = 25.9 +/- 4.3; OS = 21.9 +/- 3.9 and PLP = 15.4 +/- 3.1. The shear bond strengths of both XIII and PLP to dentine were significantly lower than the control SBMP (p < 0.05). The remaining three products (SE, ABF and OS) displayed bond strengths comparable to the control (p > 0.05). Further research into cut (ground) and un-cut (un-ground) enamel shear bond strength and micro-leakage using these bonding agents are needed.

Analysis of Variance↗
PubMed2006

Self-etching bonding systems: in-vitro micro-leakage evaluation.

The purpose of this in vitro study was to compare dentine and enamel micro-leakage values of six self-etching bonding agents to that of a total etch dentine bonding agent (used as a control). Products evaluated were Scotchbond Multipurpose Plus (3M/ESPE), Xeno III (Dentsply), Clearfil SE Bond (Kuraray), ABF (Kuraray), Optibond Solo Self-Etch (Kerr), OneCoatSE Bond (Colténe Whaledent), and iBond (Heraeus-Kulzer). Using a medium sized Cerana bur (Nordiska Dental) a standard, cylindrical preparation was made at the cemento-enamel junction (CEJ) of human third molars. The teeth were randomly divided into 7 groups of ten teeth each. The bonding agents were applied and light cured strictly according to the manufacturer's instructions and the cavities then filled in two increments, using Z100 composite (3M/ESPE). The restored teeth were imbedded in acrylic resin and thermocycled between 5 degrees - 60 degrees C (+/- 2 degrees C) for 250 cycles with a dwell time of 20 seconds. All seven groups were then placed in a 5% basic Fuchsin solution for 12 hours at 37 degrees C. The embedded teeth were removed from the basic Fuchsin, rinsed well, imbedded in acrylic and cut longitudinally through the centre of each restoration using an Accutom-2 cutting machine. Each tooth was then evaluated at the occlusal enamel margin and at the cervical dentine margin for micro-leakage using a light microscope at 50x magnification. The data obtained was analysed using the Kruskal-Wallis test, with Fisher's least significant difference method used for comparison of specific groups (p<0.05). When compared to the control (Scotchbond Multipurpose Plus), results for microleakage at the occlusal enamel margins as well as the cervical dentine margins indicated that only SE Bond and ABF (Protect Bond) showed values as low as the control. It can be concluded that, as far as micro-leakage is concerned, Clearfil SE Bond and ABF (Protect Bond) self-etching bonding agents could be clinically acceptable alternatives to the clinically proven Scotch-bond Multipurpose. The other products showed more microleakage.

Acid Etching, Dental↗
PubMed2005

Advances in light curing units and curing techniques: a literature review.

There exists a constant need for a dental curing light that works reliably and conveniently in the general practitioner's office and can be used effectively for all the different curing procedures. Due to the need for improved physical properties of resin based composites (RBCs) and less stress at the marginal interface, light curing units (LCUs) experienced significant advances in the past years. The dental industry has focused on reducing the curing time by developing higher intensity curing lights and by altering the resin composition and photo-initiator concentration. As a result the dentist can now choose from a vast variety of curing lights, light intensities and curing methods. This article presents a review of the advances in light curing units and curing techniques, as well as the scientific principles that guided past developments and that will influence future advances.

Composite Resins↗
PubMed2003

Dental materials used by general dental practitioners.

As a follow-up to previous surveys regarding materials used by dentists a total of 1500 questionnaires were distributed to general dental practitioners in private practice. A response rate of 11.8% was achieved. The most popular products used during 1999 were identified. Changes in the choices of materials were observed when compared to previous surveys. This may be attributed to the development of various new products.

Choice Behavior↗
PubMed2001

Shear bond strength of one-bottle dentine bonding systems.

The purpose of this in vitro study was to determine the shear bond strength (SBS) of composite resin to human, buccal dentine, using four one-bottle dentine bonding systems. Eighty recently extracted human molar teeth were embedded in metal rings by means of self-curing acrylic resin. The projecting buccal surfaces were ground wet on 600 grit silicone carbide paper in order to expose superficial dentine. The teeth were randomly divided into four groups (N=20): 1=Prime&tBond 2.1 (PB, Dentsply); 2=Scotchbond 1 (SB, 3M); 3=Optibond Solo (OS, Kerr) and 4=Syntac Single Component (SY, Vivadent). The dentine surfaces were etched, treated with one of the four dentine bonding systems, and cylinders of matching composites were then bonded to the surfaces by means of a silicone rubber split mould. All specimens were stored for 24 hours under water at 37 degrees C. The bonds were then stressed to failure with an Instron testing machine, operating at a crosshead speed of 0.5 mm/min. The data were statistically analysed (Kruskall-Wallis). The mean SBS (MPa) were: PB = 12.5 +/- 2.0; SB = 16.2 +/- 1.9; OS = 17.4 +/- 3.1 and SY= 8.1 +/- 1.9. There was a statistically significant difference (P = 0.0001) between the mean of SY and the other 3 groups, and also between PB and the other groups. There was no statistically significant difference (P = 0.244) between the SBS of OS and SB. SY demonstrated the lowest SBS.

Bisphenol A-Glycidyl Methacrylate↗
PubMed1996

Shear bond strength of a composite resin to differently silicoated base metal alloys.

This study was undertaken to determine the shear bond strength of Charisma composite resin to both thermal and pyrogenic silicoated base metal alloys namely, Duracast MS, Rexillium V and Wironit extra-hard. The bonded specimens were subjected to three stress treatments prior to shear bond testing. The results indicated that both silicoating techniques significantly improved shear bond strengths to sandblasted alloys, whereas wet heat and thermocycling treatments reduced the bond strengths, except for pyrogenic silicoated Wironit. Thermocycling was more detrimental to thermal than to pyrogenic silicoated Rexillium nad Wironit specimens.

Composite Resins↗
PubMed1994

Materials used by dental technicians in South Africa.

In order to determine the choice of materials used by dental technicians, questionnaires were sent to 400 registered South African dental laboratories. The response rate was 30.5 per cent. The most frequently used brands were identified. The relationship between usage of materials and demographic variables is discussed.

Dental Materials↗
PubMed1994

Continuing education for dental practitioners.

Attendance of continuing education courses by dentists is important for the practitioner, the profession and the patient. This survey was undertaken to determine the attendance pattern and discipline preferences for such courses during the period 1985 to 1989. A total of 2674 questionnaires were sent to dentists and 706 (26.4 per cent) were returned. Courses were attended by 88.5 per cent of the respondents. The most popular disciplines were Operative Dentistry, Aesthetic Dentistry and Fixed Prosthodontics.

Curriculum↗
PubMed1991

[Attitude of a group of South Africans toward advertising by dentists in private practice].

The advertising of dental services in South Africa is controlled by rules and regulations of the South African Medical and Dental Council. According to these, advertising is not permissible with the exception of specified professional information which may be made known only by means of a nameplate and an entry in a telephone directory. Questionnaires were sent to a randomised sample of 2,100 persons in order to determine the attitude of South Africans towards advertising by private practitioners. According to information obtained from this study there is a strong indication that consumers of dental services prefer a freer form of advertising by dentists in the private practice.

Adult↗
PubMed1991

The effect of placement technique on marginal adaptation of posterior resins.

Polymerization shrinkage of posterior resin restorations leads to margins that pull away from the tooth, or to cracks in the material itself. The purpose of this study was to determine the effect of three different placement techniques on the marginal adaptation (or in effect the amount of polymerization shrinkage) of posterior resin restorative materials. Three posterior resin materials, namely, Distalite, Heliomolar and P30 were included in this study. Each of these materials were placed by means of three different placement techniques (Bulk pack, Horizontal layering and Vertical layering) into class II cavities in extracted human molars. No dentine bonding agents were used. The samples were light cured, the teeth sectioned longitudinally and stored dry before examination in a Scanning Electron Microscope. Results showed polymerization shrinkage with all three techniques, with the poorest the bulk pack technique where large marginal discrepancies were visible. No significant differences were detected between the horizontal and vertical placement techniques, but the two microfilled resins Heliomolar and Distalite showed significantly poorer marginal adaptation than the small particle conventional resin, P30. All three materials had better adaptation on the occlusal margins than on the margins situated along the floor of the cavity or the gingival margins of the proximal box of the cavity. It can be concluded that the bulk pack technique should be avoided as this leads to large contraction gaps at most of the margins of the restoration.

Acrylic Resins↗
PubMed1989

[Attitude of South African dentists and final year dental students to advertising].

Advertising or promotion comprises two aspects: the advertising message and the advertising medium. Since both aspects are viewed differently by various professions, including the dental profession, the current investigation was carried out to ascertain the attitude of South African dental practitioners. Although it was found that the majority of dentists were against the advertising of new practices and re-advertising of existing practices, the majority of the final year dental students of 1986 were in favour. Both groups, however, were against unlimited advertising and also preferred professional cards to press, radio and television as the medium of communication.

Adult↗