PubMed Health⌕ Search

Biomedical subjects

J E Rubenstein

Publications and source records attributed to J E Rubenstein.

23 records · Page 2Linked to original sources

Comparison of interface relationships between implant components for laser-welded titanium frameworks and standard cast frameworks.

With the introduction of new techniques for the fabrication of frameworks for implant-supported prostheses comes the need to understand how the components used compare to those used for conventional cast frameworks. The relationship of measured machining tolerances between conventional implant components and those components used for stereo laser-welded implant frameworks was determined using a standardized protocol. Statistically significant differences in the horizontal interface relationship were found between paired implant components, which had a mean range from 23.1 to 51.7 microns. From a laboratory and clinical perspective, machining tolerances of implant components represent a variable associated with their manufacturing, which can ultimately affect the fit of a completed prosthesis.

Alloys↗

Accuracy of the acrylic resin pattern for the implant-retained prosthesis.

An in vitro study was conducted to determine the accuracy of fit of the acrylic resin pattern for the implant-supported prosthesis to the implant abutments. A master model containing five Nobelpharma titanium implants was fabricated using Ivocap acrylic resin. Using this model, five standardized acrylic resin patterns were fabricated from the three test dental acrylic resins. The fabricated patterns remained on the master model for 24 hours before removal and subsequent measurement. To compute the accuracy of each pattern, three special measuring points were firmly attached to each gold cylinder prior to pattern fabrication and the x, y, and z coordinates of these measuring points were determined. Measurements were made prior to pattern fabrication, with the cylinders on their respective abutments and after pattern fabrication, when the pattern had been removed from the master model. The results of this study showed that there was a significant difference in accuracy between the test acrylic resins and that none of these materials was completely accurate.

Acrylic Resins↗

Three-dimensional analysis of the casting accuracy of one-piece, osseointegrated implant-retained prostheses.

The three-dimensional distortions of implant frameworks of two designs, reflecting the early "Toronto" U-shaped design and a current L-shaped design, were measured. A conventional commercial laboratory one-piece casting method, using a silver-palladium alloy, was used. Distortion was defined by five displacement variables for the centroids of each of five gold cylinders incorporated in each casting: three orthogonal translational displacements (dx, dy, and dz) and two rotational displacements (d theta x and d theta y). A computerized coordinate measuring machine was used. Overall translational displacements measured were -17.4 +/- 15 microns for dx, 6.1 +/- 7.1 microns for dy, and -0.1 +/- 1.7 microns for dz. The overall global translational displacement, dR, was 20.2 +/- 14.5 microns. Overall rotational displacements were -0.098 +/- 0.109 degrees for d theta x and -0.020 +/- 0.097 degrees for d theta y, giving an average absolute angular change, d theta R, of 0.158 +/- 0.077 degrees. No significant differences were found between U- and L-shaped castings, except for dy values for cylinders 2, 3, and 4, and d theta x values for cylinder 1. Cylinder location within the arch was associated with a specific direction and magnitude of translational and rotational displacement. Even small rotational displacements may manifest large gap appearances with the one-screw test because of the "moment arm" effect. However, other rotational displacements may be hidden, depending on the direction of tilt and the moment arm length.

Analysis of Variance↗

Tolerance measurements of various implant components.

Machining tolerance, an intrinsic characteristic that exists between machined implant components, identifies the amount of horizontal shift possible between paired components. Machining tolerances between implant components (abutment, gold, cylinder, impression coping, and brass abutment replicas) were measured with a coordinate measuring machine. The measured tolerances ranged from 22 to 100 microns. Machining tolerances between implant components should be included in future studies of accuracy, because it is an inherent characteristic of the component itself.

Alloys↗

Ten-year results for Brånemark implants immediately loaded with fixed prostheses at implant placement.

This investigation was initiated to develop a method to provide patients with a fixed provisional prosthesis placed at the time of implant placement. Sixty-three standard 3.75-mm Nobel Biocare implants of varying lengths were placed into mandibular sites in 10 patients and followed for up to 10 years. Twenty-eight implants were immediately loaded at implant placement, providing support for fixed provisional prostheses, while 35 adjacent implants were allowed to heal submerged and stress-free. Following a 3-month healing period, the submerged implants were exposed and definitive reconstruction was accomplished. All 10 prostheses supported by 28 implants placed into immediate function at the time of implant placement were successful during the 3-month healing period. Of these 28 implants placed into immediate function, 4 ultimately failed. Of the 35 submerged implants, all are osseointegrated and in function to date. Life-table analysis demonstrates an overall 10-year survival rate of 93.4% for all implants. The 10-year life-table analysis of survival is 84.7% for immediately loaded implants and 100% for submerged implants. Statistical analysis of the submerged versus immediately loaded implants demonstrates failure rates for immediately loaded implants to be significantly higher (P = .022 by the log rank test). These data demonstrate that although mandibular implants can be successfully placed into immediate function in the short term to support fixed provisional prostheses, long-term prognosis is guarded for those implants placed into immediate function distal to the incisor region.

Aged↗