PubMed Health⌕ Search

Biomedical subjects

J G van der Watt

Publications and source records attributed to J G van der Watt.

6 recordsLinked to original sources
PubMed2000

Structure-solubility relationship and thermal decomposition of furosemide.

Furosemide, a high ceiling diuretic, decomposes on heating and is very sparingly soluble in water. The aim of this study was to identify the thermal decomposition product(s) of furosemide and to calculate the activation energy needed for this reaction. This was done to gain a better understanding of the unusually low water solubility of this drug. The main thermal decomposition product was identified by nuclear magnetic resonance (NMR), mass spectrometry (MS), and infrared (IR) analysis as 4-chloro-5-sulfamoylanthranilic acid (saluamine), and the activation energy, calculated from thermogravimetric analysis (TGA) measurements, for this reaction was 47.7 (+/- 1.93) kcal/mol. The experimentally measured activation energy was well below the normal 59 +/- 4 kcal/mol needed for the cleavage of the C-N bond to form saluamine. This could possibly be explained by the weakening of the C-N bond through the I-effect of the furane ring and the delocalization of the electrons of the aniline nitrogen in the chlorosulfamoyl benzoic acid entity of furosemide. This decomposition of furosemide indicates the breaking of intramolecular bonds before those of intermolecular bonds (separation of individual furosemide molecules). Strong inter- and intramolecular bonds are a probable cause for the poor water solubility of furosemide because, when some of the inter- and intramolecular bonds that form part of the hydrogen bond network disappeared, as in the structurally related decomposition product saluamine, the aqueous solubility increased.

Diuretics↗
PubMed1998

Pharmacokinetic evaluation in dogs of theophylline in a novel zero-order release core-in-cup tablet.

A new core-in-cup tablet that is manufactured from a novel adjustable punch, has been formulated and evaluated for its ability to release with subsequent absorption of theophylline via a zero-order rate of absorption. The core-in-cup tablets were compared with core only tablets and immediate release capsules. Pharmacokinetic parameters used to test the effectiveness of the formulations included, elimination rate, rate and kinetic order of absorption, relative availability as compared with an immediate release capsule of pure theophylline, and percentage area under the curve fluctuation (%AUCF) at steady state. The correlation coefficient, Akaike's information criterion (AIC) and the F-ratio probability were used to test the applicability of a zero-order, first-order, or square root of time model, for the rate of release of theophylline from the core-in-cup and core only tablets. The zero-order rate model was most applicable to the core-in-cup tablet, whereas the square root of time release model was most applicable to the core only tablet. The average %AUCF for the core-in-cup tablet was 9.26+/-3.15 while that for the core only tablet was 16.19+/-2.37 (p = 0.0545). The results of this study suggest that the core-in-cup tablet is a versatile zero-order release rate dosage form that are simple to produce.

Animals↗
PubMed1998

Zero-order release of theophylline from a core-in-cup tablet in sequenced simulated gastric and intestinal fluid.

Core-in-cup tablets containing theophylline were evaluated for their dissolution characteristics in sequenced simulated gastric fluid (SGF) followed by simulated intestinalfluid (SIF). Core-in-cup tablets containing 10% w/w, 20% w/w, and 30% w/w acacia as binder were evaluated for their effects on the time course of release of theophylline. This was done to optimize a formula that could release theophylline at a zero-order rate of release for 8-16 hr in simulated gastrointestinal fluids. Theophylline was released and dissolved from the core-in-cup tablets at a rate that is more consistent with a zero-order dissolution rate than a first-order dissolution rate in both SIG and SIF. The dissolution rates of theophylline from the 10%, 20%, and 30% acacia core-in-cup tablets were 0.87 mg/min, 0.53 mg/min, and 0.27 mg/min, respectively in SGF, and 0.61 mg/min, 0.30 mg/min, and 0.20 mg/min, respectively in SIF. The results indicate that a concentration of 32% w/w acacia in the core tablet will release theophylline at a rate of 0.14 mg/min in SGF for 2 hr followed by SIF for 10 hr.

Administration, Oral↗
PubMed1998

A study of the changes during heating of paracetamol.

The orthorhombic form of paracetamol has been shown to exhibit greater compressibility and faster dissolution than the monoclinic form. The orthorhombic form is produced by melting of monoclinic crystals of paracetamol followed by cooling at specific rates. Cooling rate, although a very important factor, is not the only factor influencing the formation of either of the two morphs. To study the cooling rate required for production of form II, paracetamol samples were melted in a differential scanning calorimeter, cooled at three specific rates, and melted again. In all of the samples, cooling resulted in the glassy form followed by recrystallization and the melting of form II. On the hot-stage microscope both forms were produced in one sample. Standardizing conditions for prediction of the resulting form remains a problem. There seems to be a great deal of overlap of the two forms' transition phases, which would make it difficult to force the crystallization of one form by keeping the solution or melt at a specific temperature. The thermal behavior of paracetamol during the heating and cooling phases must be understood in order to manipulate the process. A video camera mounted on a hot-stage microscope was used to follow the changes during heating and cooling of both forms. Nucleation, crystal growth, habit transformation, sublimation, and the final melt are shown on snap shots taken from the video.

Acetaminophen↗
PubMed1989

Physical and structural comparison of oxyphenbutazone monohydrate and anhydrate.

Two crystal forms of oxyphenbutazone (a monohydrate and an anhydrate) were prepared by recrystallization. The forms were characterized by means of differential scanning calorimetry, thermogravimetry, infrared spectrophotometry, X-ray powder diffraction patterns, thermomicroscopy, scanning electron microscopy, as well as powder and intrinsic dissolution rates. The crystal structure of the anhydrate has been elucidated and compared with that of the monohydrate.

Calorimetry, Differential Scanning↗