Biomedical subjects

J I Golzarri

Publications and source records attributed to J I Golzarri.

5 recordsLinked to original sources

PubMed2006

Study of gel materials as radioactive 222Rn gas detectors.

Commercial hair gel material (polyvinyl pyrolydone triethanolamine carbopol in water) and bacteriological agar (phycocolloid extracted from a group of red-purple algae, usually Gelidium sp.) have been studied as radioactive radon gas detectors. The detection method is based on the diffusion of the radioactive gas in the gel material, and the subsequent measurement of trapped products of the natural decay of radon by gamma spectrometry. From the several radon daughters with gamma radiation emission (214Pb, 214Bi, 214Po, 210Pb, 210Po), two elements, 214Pb (0.352 MeV) and 214Bi (0.609 MeV), were chosen for the analysis in this work; in order to determine the best sensitivity, corrections were made for the short half-life of the analysed isotopes. For the gamma spectrometry analysis, a hyperpure germanium solid state detector was used, associated with a PC multichannel analyser card with Maestro and Microsoft Excel software. The results show the viability of the method: a linear response in a wide radon concentration range (450-10,000 Bq m(-3)), reproducibility of data, easy handling and low cost of the gel material. This detection methodology opens new possibilities for measurements of radon and other radioactive gases.

Dose-Response Relationship, Radiation↗

PubMed2006

Commercial optical fibre as TLD material.

This work presents a study of commercial SiO2 optical fibre thermoluminescence (TL) properties as part of the efforts within the Dosimetric Application Project at the Physics Institute of the University of Mexico to develop new radiation detection materials and technologies. The SiO2 commercial optical fibre studied demonstrates useful TL properties and is an excellent candidate for use in TL dosimetry of ionising radiation. The optical fibre's glow curve was observed between 30 and 400 degrees C after exposure to 60Co gamma radiation. One very well-defined glow peak has a maximum at 230 degrees C. The TL response between 100 and 350 degrees C increases monotonically over a wide dose range, from 0.1 Gy to several kGy. It is linear in the range 0.1-3 Gy, which is important for clinical high dose or accident dosimetry. The optical fibre demonstrated high data reproducibility, low residual signal and almost no fading in our study. Moreover, the optical fibre can be re-used several times, after thermal annealing, without any detriment in the dose-response. All these TL characteristics, plus the small size of the 150 microm diameter SiO2 optical fibre, the high flexibility, easy handling and low cost compared with other TL materials, make the commercial optical fibre a very promising TL material for use in research, medicine, industry, reactors, and a variety of other applications.

Dose-Response Relationship, Radiation↗

PubMed2002

Neutron angular distribution in a plasma focus obtained using nuclear track detectors.

The dense plasma focus (DPF) is a coaxial plasma gun in which a high-density, high-temperature plasma is obtained in a focused column for a few nanoseconds. When the filling gas is deuterium, neutrons can be obtained from fusion reactions. These are partially due to a beam of deuterons which are accelerated against the background hot plasma by large electric fields originating from plasma instabilities. Due to a beam-target effect, the angular distribution of the neutron emission is anisotropic, peaked in the forward direction along the axis of the gun. The purpose of this work is to illustrate the use of CR-39 nuclear track detectors as a diagnostic tool in the determination of the time-integrated neutron angular distribution. For the case studied in this work, neutron emission is found to have a 70% contribution from isotropic radiation and a 30% contribution from anisotropic radiation.

Copper↗

PubMed2002

Nuclear tracks in CR-39 produced by carbon, oxygen, aluminium and titanium ions.

This work describes the response of CR-39 (allyl diglycol polycarbonate) to different ions (C, O, Al and Ti) produced by the Instituto de Fisica 3 MV 9SDH-2 Pelletron accelerator and backscattered from a thin Au film on a C support. The ion energies were chosen in series such that the ranges of the different ions in the detector were 2, 3, 4, 5, 6, 7 and 8 microm respectively for each series. Once exposed, the detectors were etched with a solution of 6.25 M KOH at 60 degrees C, and the reading was carried out using a digital image analysis system. An analysis of the measured track diameters of all the types of ions indicates that, for a given range, track kinetics are independent of type of ion, energy and stopping power.

Aluminum↗

PubMed2002

Analysis of the formed track in solid state materials using atomic force microscopy.

The track formation in solid state materials, from the theoretical point of view, is still under study. One way to understand the track formation mechanisms and radiation damage of the charged particles in some materials such as polymers, glasses and minerals, is to analyse the surface topography effects. In this work, the track formation analysis in polycarbonate material is presented using an atomic force microscope (AFM) to characterise the evolution of the track on the material surface and beyond a thin layer of the surface material. The AFM is very useful to obtain valuable information at the level of the atomic structure of the materials and of the nuclear tracks, due to its high resolution and very easy operation involving also a simple sample preparation. The results show the development of the formed track by means of induced surface effects after being exposed to ionising radiation and chemical etching.

Microscopy, Atomic Force↗