Biomedical subjects

J P H Linssen

Publications and source records attributed to J P H Linssen.

7 recordsLinked to original sources

PubMed2004

Feasibility study for the development of certified reference materials for specific migration testing. Part 1: initial migrant concentration and specific migration.

The paper describes a project with the main objective of developing the know how to produce certified reference materials (CRMs) for specific migration testing. Certification parameters discussed are the initial concentration of the migrant in the polymer (C(P),0) and the specific migration into a food simulant under certain temperature/time conditions. Sixteen preliminary candidate CRMs were defined and produced. The most important polymers (low- and high-density polyethylene (LDPE and HDPE), polypropylene (PP), polystyrene (PS), polyethylene terephtalate (PET), plasticized polyvinyl chloride (PVC), rigid PVC, polyamides (PA)) and additives as well as monomers representing different physicochemical properties as target substances for migration were chosen. The stability and homogeneity of the migrants in the materials were tested and methods for the determination of the certification parameters were developed and validated. > From the 16 materials produced, the six most suitable CRM candidates (LDPE//Irganox 1076/Irgafos 168, LDPE//1,4-diphenyl-1,3-butadiene (DPBD), HDPE//Chimassorb 81/Uvitex OB, PP homo//Irganox 1076/Irgafos 168, HIPS, 1% mineral oil//styrene, PA 6//caprolactam) were selected. The feasibility of CRM production for the six candidate materials was demonstrated and a trial certification exercise was performed with participation of all four partner laboratories. All six materials showed suitable properties for future production as certified reference materials.

Consumer Product Safety↗

PubMed2003

Influence of flavour absorption by food-packaging materials (low-density polyethylene, polycarbonate and polyethylene terephthalate) on taste perception of a model solution and orange juice.

The influence of flavour absorption by low-density polyethylene (LDPE), polycarbonate (PC) and polyethylene terephthalate (PET) on taste perception of a model solution containing seven flavour compounds and orange juice in glass bottles was studied with and without pieces of the respective plastic films after dark storage at 20 degrees C. Owing to absorption, the amount of flavour compounds in the model solution exposed to LDPE decreased substantially. From the model flavour solution valencene was almost completely absorbed by LDPE, followed to a lesser extent by decanal, hexyl acetate, octanal and nonanone. Less flavour compounds were absorbed from the model solution by PC and PET. In contrast to LDPE, valencene was absorbed in the lowest amounts and decanal in the highest. Limonene was readily absorbed from orange juice by LDPE, while myrcene, valencene, pinene and decanal were absorbed in smaller quantities. Only three flavour compounds were absorbed from orange juice by PC and PET in very small amounts: limonene, myrcene and decanal. Although the flavour content between controls and polymer-treated samples differed substantially, the loss of flavour compounds due to absorption by LDPE, PC and PET did not influence taste perception of a model solution and orange juice significantly up to 29 days of dark storage at 20 degrees C as determined by triangular taste panel tests.

Absorption↗

PubMed2003

Modelling the effect of oil/fat content in food systems on flavour absorption by LLDPE.

One of the phenomena in food-packaging interactions is flavour absorption. Absorption of flavour compounds from food products into food-packaging materials can result in loss of flavour compounds or an unbalance in the flavour profile changing a product's quality. The food matrix influences the amounts of absorbed flavour compounds; the presence of oil or fat especially determines the ability to absorb flavour compounds from the food to the package. On the other hand, the polarity of the flavour compound itself is a characteristic that also influences the level of absorption into synthetic polymers. A model based on the effect of the polarity (logP) of flavour compounds and on their partitioning coefficients between the food (matrix) and the packaging material is described. The model can be used for predicting absorption of flavour compounds from foods into LLDPE. However, an attempt to apply the proposed model on real foods shows serious limitations of the model for (very) low fat products. Predictive values deviate from the measured values, probably due to other interaction phenomena, e.g. with proteins. Predictive and measured values from a product with a substantial amount of fat match much better, suggesting that the model is valid for products having a substantial amount of (free) fat.

Absorption↗

PubMed2003

Development and validation of analytical methods for monomeric and oligomeric migrants from nylon 12 packaging materials.

Analytical methods for the determination of laurolactam--the monomer of nylon 12--as well as the cyclic dimer and trimer were established. High performance liquid chromatography using ultraviolet (HPLC-UV) and mass spectrometric detection (HPLC-MS) were both found suitable to identify and quantify monomer, cyclic dimer and trimer well below the specific migration limit (SML) of laurolactam, being 5 mg/kg of food (simulant). Gas chromatography with flame ionisation detection (GC-FID) showed to be an appropriate method for the detection of only laurolactam in aqueous and fatty food simulants. Food simulants could be analysed directly by all three methods, or after a change of solvents. For olive oil, a method for sample clean-up by size-exclusion chromatography (SEC) was established.

Chromatography, Gas↗

PubMed2003

Alternative fatty food simulants and diffusion kinetics of nylon 12 food packaging.

The migration of laurolactam and cyclic di- and trimer of nylon 12 was assessed using three different films and five food simulants (olive oil, isooctane, 95% ethanol, 50% ethanol, water). Substitute test conditions for migration into olive oil according to European Union Directive EC/97/48 were applied using 95% ethanol and isooctane. Results showed that 95% ethanol overestimated while isooctane underestimated the respective migration into olive oil. Water was the best olive oil substitute, as migration of laurolactam into water and olive oil using the same temperature gave similar results. Additionally, diffusion kinetics of laurolactam were investigated by migration kinetic studies using isooctane and olive oil. Diffusion coefficients determined with isooctane were significantly higher than those found using olive oil. It was proved that isooctane had an interaction and olive oil was inert to the polymer. The diffusion conductance parameter, A(p), for nylon 12 determined using olive oil ranged from 0.3 to 0.6.

Dietary Fats↗

PubMed2002

Antioxidant properties of differently processed spinach products.

The effect of variously processed spinach products (whole-leaf, minced and enzymatically liquefied spinach) on lipid oxidation was determined. In an autoxidative methyl linoleate (MeLo) system the inhibition of hydroperoxide formation, measured by HPLC after three days of oxidation, was in descending order: whole-leaf > liquefied > minced spinach. The inhibition of formation of thiobarbituric acid-reactive substances (TBARS) and hexanal by spinach was determined in cooked meatballs with added spinach after two days of storage at 4 degrees C. The formation of TBARS was inhibited by liquefied spinach at 200 g/kg meat; all other spinach products tested at 100 and 200 g/kg were pro-oxidative. The formation of hexanal was inhibited by both minced and liquefied spinach at 100 and 200 g/kg meat. The variously processed spinach products behaved differently when tested for their antioxidant activity (MeLo) or oxidative stability (meatballs). We conclude that the effect of spinach products on lipid oxidation is affected by processing.

Aldehydes↗

PubMed2002

Influence of flavour absorption on oxygen permeation through LDPE, PP, PC and PET plastics food packaging.

The effect of flavour absorption on the oxygen permeability of low-density polyethylene (LDPE), polypropylene (PP), polycarbonate (PC) and polyethylene terephthalate (PET) was studied using an isostatic continuous flow system. Polymer samples were exposed to a model solution containing limonene, hexyl acetate, nonanone and decanal at 40 degrees C. After exposure, one part of each sample was analysed for absorbed flavour compounds using a Large Volume Injection GC Ultrasonic 'in vial' extraction method, and from the other part, oxygen permeability was measured in a permeation cell at 25 degrees C. After 8 h of exposure, LDPE and PP samples showed a significant linear (R2 = 0.82 and 0.99) increase in oxygen permeability of 21 and 130%, respectively. Owing to swelling of the polymer samples resulting from flavour absorption, the structure of the polymeric network changed (i.e. opened) and consequently increased oxygen permeability. The oxygen permeability of exposed PC showed a significant linear (R2 = 0.78) decrease of 11% after 21 days. PC obviously did not swell like LDPE or PP. Therefore, it was suggested that absorbed flavour compounds occupied or blocked 'microcavities' through which normally oxygen is transported. Absorption of flavour compounds by PET did not affect the oxygen permeability of PET significantly.

Absorption↗