Biomedical subjects

J P Remon

Publications and source records attributed to J P Remon.

At least 55 records · Page 3Linked to original sources

PubMed2002

Direct compression properties of melt-extruded isomalt.

Isomalt, a sugar alcohol, was melt-extruded prior to compression in order to improve its tabletting properties. After fusion, crystalline isomalt was transformed into an amorphous form as shown by X-ray diffraction and differential scanning calorimetry (DSC). The tabletting properties of amorphous isomalt were dramatically improved. Mixtures formulated with paracetamol (50%) and extruded isomalt yielded hard tablets. However, extruded isomalt powder showed agglomeration problems due to recrystallization of the amorphous phase into a stable crystalline form in the presence of atmospheric moisture. The evolution of the moisture content correlated well with the compressibility data. The tablets made of extruded isomalt powder had a lower friability in comparison to the tablets formulated with non-extruded isomalt powder. Their disintegration was fast and a rapid dissolution rate was recorded. Extruded isomalt displayed excellent tabletting properties; however, further experiments should be conducted to delay or even prevent recrystallization of amorphous isomalt.

Cariogenic Agents↗

PubMed2002

Direct compression and moulding properties of co-extruded isomalt/drug mixtures.

Isomalt, a disaccharide alcohol was co-extruded with paracetamol or hydrochlorothiazide (HCT) in order to improve its tabletting properties. After extrusion, isomalt was transformed into an amorphous form, while paracetamol remained crystalline. Hot stage microscopy showed that HCT was amorphous in the isomalt carrier up to a concentration of 1% (w/w). Direct compression of mixtures formulated with co-extruded isomalt/paracetamol powders yielded harder tablets compared with physical mixtures and no powder agglomeration was observed. Direct moulding of isomalt co-extruded with either paracetamol or HCT was feasible, yielding hard tablets. A fast dissolution rate was seen for both the compressed and the moulded tablets (>80% paracetamol and 60% HCT released within 20 min). The compressed tablets showed a dramatic decrease in tensile strength during storage at 85% RH, while the tensile strength of the moulded tablets remained above 0.80 MPa after 6 months storage at the same conditions. Co-extrusion of isomalt with paracetamol and HCT dramatically improved the tabletting properties of the mixtures (compared with physical mixtures of drug and isomalt). Direct moulding proved to be a suitable technique to produce isomalt based tablets.

Acetaminophen↗

PubMed2002

Ex vivo bioadhesion and in vivo testosterone bioavailability study of different bioadhesive formulations based on starch-g-poly(acrylic acid) copolymers and starch/poly(acrylic acid) mixtures.

Starch-g-poly(acrylic acid) copolymers or grafted starches synthesized by 60Co irradiation or chemical modification and co-freeze-dried starch/poly(acrylic acid) mixtures were evaluated on their ex vivo bioadhesion capacity. The buccal absorption of testosterone from a bioadhesive tablet formulated with the grafted starches or starch/poly(acrylic acid) mixtures was investigated. The results were compared to a reference formulation (physical mixture of 5% Carbopol 974P and 95% Drum Dried Waxy Maize). Rice starch-based irradiated grafted starches showed the best bioadhesion results. Partial neutralization of the acrylic acid with Ca(2+) ions resulted in significantly higher bioadhesion values compared to the reference. Ca(2+) and Mg(2+) partially neutralized maltodextrin-based irradiated grafted starches showed significantly higher bioadhesion values compared to the reference formulation. The chemically modified grafted starches showed significantly higher adhesion force values than for the reference tablet. None of the co-freeze-dried starch/poly(acrylic acid) mixtures showed significantly higher bioadhesion results than the reference (Bonferroni test, P<0.05). A chemically modified grafted starch could sustain the 3 ng/ml plasma testosterone target concentration during +/- 8 h (T(>3 ng/ml)). By lyophilization of a partially neutralized irradiated grafted starch, the in vivo adhesion time (22.0 +/- 7.2 h) and the T(>3 ng/ml) (13.5 +/- 1.3 h) could be increased. The absolute bioavailability of the lyophilized formulation approached the reference formulation. Some of the grafted starches showed to be promising buccal bioadhesive drug carriers for systemic delivery.

Adhesives↗

PubMed2002

Characterization of ibuprofen as a nontraditional plasticizer of ethyl cellulose.

This study describes the characterization of the plasticizing properties of ibuprofen (IBP) on hot-melt extruded ethyl cellulose (EC). The thermal behavior of hot-melt extrudates containing 0, 5, 10, and 20% (w/w) IBP was evaluated using modulated temperature differential scanning calorimetry. By means of comparison, co-evaporates containing the same concentrations of IBP and EC, were also evaluated. Both methods yielded solid solutions having one glass transition temperature indicating compatibility between drug and polymer. A similar decrease in glass transition temperature was noticed with increasing IBP concentration in the solid solutions prepared via both methods, indicating its plasticizing effect. The plasticizing efficiency was of the same magnitude as for the traditionally used plasticizers. Infrared spectroscopy was performed for better understanding of the chemical interactions in the molecular dispersions and confirmed the existence of hydrogen bonds between IBP and EC. Overall, the study has highlighted the plasticizing properties of IBP on EC during hot-melt extrusion.

Cellulose↗

PubMed2002

Wax beads as cushioning agents during the compression of coated diltiazem pellets.

Placebo particles were mixed with film-coated diltiazem pellets to evaluate them as cushioning agents during tabletting in order to protect the film coat from damage. The cushioning properties of alpha-lactose monohydrate granules, microcrystalline cellulose pellets and wax/starch beads were evaluated by comparing the dissolution profile of the coated pellets before and after compression (compression force 10 kN). Only the tablet formulations containing wax/starch beads provided protection to the film coat. However, the dissolution rate of tablets formulated with waxy maltodextrin/paraffinic wax placebo beads was too slow as the tablets did not disintegrate. Adding 50% (w/w) drum-dried corn starch/Explotab/paraffinic wax beads to the formulation was the optimal amount of cushioning beads to provide sufficient protection for the film coat and yield disintegrating tablets. Using a compression simulator, the effect of precompression force and compression time on the dissolution rate was found to be insignificant. The diametral crushing strength of tablets containing 50% (w/w) drum-dried corn starch/Explotab/paraffinic wax beads was about 25.0 N (+/-0.3 N), with a friability of 0.4% (+/-0.04%). This study demonstrates that adding deformable wax pellets minimizes the damage to film-coated pellets during compression.

Compressive Strength↗

PubMed2001

Evaluation of a mucoadhesive tablet for ocular use.

The present study investigates the use of a polymer mixture containing Carbopol 974P and drum dried waxy maize starch to obtain prolonged drug release to the anterior eye segment. Two dosage forms with this composition are compared: a hydrated polymer dispersion and a minitablet. A model fluorescent tracer is used to study the ocular release and diffusion from the two dosage forms in humans. To evaluate the prolongation in the cornea/tearfilm compartment, the Apparent Fluorescein TurnOver (%/min) is calculated. The parameters Cmax, tmax, and C9h are used to characterize the pharmacokinetics of Na-fluorescein in the anterior chamber. Furthermore, the swelling behavior of the minitablet is evaluated macroscopically, while the degree of interaction with mucin is characterized by rheological measurements. Calculation of an acceptability score and a slug irritation potential is performed to evaluate user acceptability. In contrast to the hydrated dispersion, the minitablet significantly decreases the Apparent Fluorescein TurnOver (%/min) (P<0.05) and increases the apparent fluorescence in the anterior chamber 9 h after application of the preparation. Rheological data demonstrate the presence of elastic interactions between the polymer and mucin. The dry core of the minitablet becomes fully hydrated after approximately 2 h and is subsequently transformed into a highly concentrated gel. The acceptability of the minitablet is comparable to that of the polymer dispersion. Prolonging the release of Na-fluorescein to the anterior eye segment is only feasible with the dry preparation.

Acrylates↗

PubMed2001

Toxicological evaluation of a bioadhesive nasal powder containing a starch and Carbopol 974 P on rabbit nasal mucosa and slug mucosa.

The purpose of this study is the investigation of possible adverse effects of a powder formulation containing drum-dried waxy maize (DDWM) starch and Carbopol 974 P (90/10) on the nasal mucosa of rabbits and the foot mucosa of slugs after multiple administrations. In the rabbit, the effect of the formulation was measured by the release of proteins and lactate dehydrogenase (LDH) from the nasal mucosa with a new non-invasive in vivo method and also by histopathology. The mucosal toxicity of the formulation was evaluated using slugs by measuring the effect on the body weight and the amount of mucus produced during a repeated contact period. Additionally, the release of proteins, lactate dehydrogenase and alkaline phosphatase from the body wall of the slugs after a repeated treatment was measured. Twenty four hours after the powder administration to the rabbits the release of the marker molecules was comparable with the negative controls. The histopathological study showed only a slight increase of granulocytes in the epithelium. The formulation induced a higher mucus production in the slugs but no additional effects were detected on the body weight and on the release of proteins. No enzymes were released from the body wall. The results indicate that the effect of the bioadhesive powder consisting of DDWM/Carbopol 974 P (90:10, w/w) on the mucosa was negligible.

Acrylates↗

PubMed2001

Trypsin inhibition, calcium and zinc ion binding of starch-g-poly(acrylic acid) copolymers and starch/poly(acrylic acid) mixtures for peroral peptide drug delivery.

Newly synthesised starch-g-poly(acrylic acid) copolymers and starch/poly(acrylic acid) mixtures were evaluated for their in vitro inhibition potency towards the proteolytic enzyme trypsin. Their Ca2+ and Zn2+ binding capacity was measured. Carbopol 934P was used as reference polymer. Starch-g-poly(acrylic acid) copolymers were prepared by chemical grafting and 60Co irradiation, the starch/poly(acrylic acid) mixtures by freeze-drying. The influence of preparation method, the ratio starch:acrylic acid, the neutralisation degree and for the freeze-dried polymers the influence of heat treatment after freeze-drying was investigated. All freeze-dried polymers showed a higher inhibition factor (IF) than the chemically grafted and 60Co irradiated starches, which all showed significantly lower IF than Carbopol 934P. The heat treated freeze-dried polymer Amioca/poly(acrylic acid) (1:1) showed a significantly higher IF than the reference polymer (Mann-Whitney test, p<0.05). The Ca2+ and Zn2+ binding capacity of all chemically grafted starches was much lower than for Carbopol 934P. Only the 60Co irradiated starches and freeze-dried polymers with ratio 1:3 approached the binding capacity of the reference polymer. The freeze-dried polymers showed the highest proteolytic enzyme inhibition potency. Freeze-drying and 60Co irradiation could result in the highest ion binding capacity. This combination of proteolytic enzyme inhibition activity and ion binding capacity makes these polymers hopeful excipients for successful oral peptide delivery.

Acrylic Resins↗

PubMed2001

In vitro and in vivo evaluation of starch-based hot stage extruded double matrix systems.

The objective of developing a double matrix system consisting of a hot stage extruded starch pipe surrounding a hot stage extruded and drug-containing starch core, was to obtain a monolithic matrix system applicable in the domain of sustained drug release. The behaviour of the systems was evaluated through dissolution testing and through a randomised crossover bioavailability study on nine male volunteers. All double matrix systems showed in vitro a nearly constant drug release profile after an initial slower release phase of 4 h. This initial slower release phase was avoided by loading the starch pipe with a small amount of drug. The in vitro dissolution profiles did not reflect the in vivo behaviour of the systems. Although the in vitro dissolution profiles of two selected double matrix systems were slower than the profile of a commercially available sustained release formulation, they performed less well in vivo. However, the t75%Cmax ratios of the evaluated double matrix systems versus a reference immediate release formulation indicated an acceptable sustained release behaviour, superior to that of hot stage extruded starch-based single matrices. Therefore the disclosed drug delivery systems could be applied in the domain of sustained drug delivery. Besides, the continuous production of the double matrix systems offers an advantage from a manufacturing point of view.

Adult↗

PubMed2001

Characterisation and disintegration properties of irradiated starch.

Irradiation treatment could provide a quick and simple way to modify the physical, chemical and pharmaceutical properties of biopolymers such as starch. Corn, potato and drum dried corn starch were exposed to X-ray and electron beam (e-beam) irradiation treatment at doses of 10, 50 and 100 kGy. The disintegration properties of these starches were compared using alpha-lactose monohydrate tablets containing 5% (w/w) starch as disintegrant. Starch solubility increased, while its swelling capacity decreased with increasing irradiation dose. The irradiation treatment caused fragmentation of the amylopectin fraction. Irradiation modified the different starches thoroughly, showing remarkable differences in disintegration properties after X-ray treatment and e-beam modification. The e-beam modification resulted in significantly higher disintegration times of the tablets.

Molecular Weight↗

PubMed2001

An oral controlled release matrix pellet formulation containing nanocrystalline ketoprofen.

A controlled release pellet formulation using a NanoCrystal colloidal dispersion of ketoprofen was developed. In order to be able to process the aqueous NanoCrystal colloidal dispersion into a hydrophobic solid dosage form a spray drying procedure was used. The in vitro dissolution profiles of wax based pellets loaded with nanocrystalline ketoprofen are compared with the profiles of wax based pellets loaded with microcrystalline ketoprofen and of a commercial sustained release ketoprofen formulation. Pellets were produced using a melt pelletisation technique. All pellet formulations were composed of a mixture of microcrystalline wax and starch derivatives. The starch derivatives used were waxy maltodextrin and drum dried corn starch. Varying the concentration of drum dried corn starch increased the release rate of ketoprofen but the ketoprofen recovery remained problematic. To increase the dissolution yield surfactants were utilised. The surfactants were either added during the production process of the NanoCrystal colloidal dispersion (sodium laurylsulphate) or during the pellet manufacturing process (Cremophor RH 40). Both methods resulted in a sustained but complete release of nanocrystalline ketoprofen from the matrix pellet formulations.

Administration, Oral↗

PubMed2001

Cold extrusion as a continuous single-step granulation and tabletting process.

The potential of cold extrusion as a continuous granulation/tabletting technique was investigated. Extrudates (X, 9 mm) were produced using twin-screw extrusion, cut manually into tablets (thickness, 4 mm) and dried at 25 degrees C for 20 h. alpha-Lactose monohydrate (200 M) was used as an excipient, PVP (Kollidon K30) and water as binders, and hydrochlorothiazide as the model drug. The influence of formulation (water content, PVP addition, drug incorporation) and process (total input rate and screw speed) parameters on the process (torque, die pressure, visual evaluation of tablets) and on the tablet properties (tensile strength, friability, disintegration time, porosity) was evaluated. Formulation, as well as process parameters, affected the process feasibility, but had only a minor effect on the tablet properties at conditions that allowed continuous tablet production. All alpha-lactose monohydrate tablets formulated without and with PVP and produced at optimum conditions showed tensile strengths above 0.7 and 1.5 MPa, friabilities below 1.0 and 0.9%, and disintegration times below 1 and 8 min, respectively. This technique allows single-step granulation/tabletting of pure alpha-lactose monohydrate, indicating that cold extrusion could be used as alternative tablet production technique for ingredients with poor compaction properties. As the tablets prepared by extrusion have a much higher porosity compared with conventional tablets, this technique could also be useful for tablet production of formulations with poor disintegrating properties.

Chemistry, Pharmaceutical↗

PubMed2001

The mucosal toxicity of different benzalkonium chloride analogues evaluated with an alternative test using slugs.

PURPOSE: The objective of this study was to evaluate the mucosal toxicity of different benzalkonium chloride (BAC) analogues using slugs as the alternative test organism. METHODS: The effect of different BAC analogues on the mucosal tissue of slugs was determined from the protein, lactate dehydrogenase, and alkaline phosphatase released from the foot mucosa after treatment. Additionally, mucus production and reduction in body weight of the slugs were measured. The eye irritation potency of the molecules was evaluated with the Bovine Corneal Opacity and Permeability (BCOP) assay. The antimicrobial activity of the different BAC analogues was also assessed. RESULTS: All BAC analogues induced severe damage to the mucosal epithelium of the slugs, and the irritation increased with decreasing alkyl chain length: BAC-C16 < BAC-C14 < BAC-C12 approximately BAC-mix. A similar ranking was obtained with the BCOP assay for eye irritation. The relative order of activities among the three BAC analogues was the same, i.e., BAC-C14 > or = BAC-C16 > BAC-C12. The BAC-C14 exhibited higher activity than the BAC-mix. CONCLUSIONS: The toxicity and activity of BAC analogues depend on the alkyl chain length. The use of BAC-C14 as a conservative agent in pharmaceutical preparations instead of the BAC-mix should be considered.

Alkaline Phosphatase↗

PubMed2001

The oral bioavailability of ibuprofen enantiomers in broiler chickens.

Doses of racemic ibuprofen ranging from 5 to 20 mg/kg body weight were administered intravenously (i.v.) and orally to broiler chickens and plasma concentration-time profiles for both ibuprofen enantiomers were determined. The absorption of ibuprofen was evaluated after a bolus administration of a commercially available suspension into the crop and proventriculus, respectively. An enterohepatic circulation as described for other nonsteroidal anti-inflammatory drugs (NSAIDs) in other species could be suggested for both enantiomers after i.v. and oral administration. Significantly higher area under the curve (AUC) values for S(+)-ibuprofen compared with R(-)-ibuprofen were collected after crop and proventriculus administration. Several factors could be responsible for the significant differences in AUC values between both enantiomers.

Absorption↗

PubMed2000

Validation of a high-performance liquid chromatographic method for the determination of ibuprofen enantiomers in plasma of broiler chickens.

To characterise the pharmacokinetic properties of each enantiomer of ibuprofen in broiler chickens, a stereospecific HPLC method based on a alpha1-acid glycoprotein bonded chiral stationary phase has been validated. S-(+)-naproxen was used as internal standard. Enantiomers of ibuprofen and S-(+)-naproxen were baseline separated using a mobile phase consisting of 0.1 M phosphate buffer pH = 7 and 0.4% 2-propanol. The method is precise, specific, accurate and reproducible. Recoveries were higher than 80% and the limits of quantification for R-(-)- and S-(+)-ibuprofen were 1.16 and 1.37 microg ml(-1), respectively. The method seemed suitable for the pharmacokinetic studies of ibuprofen in chickens.

2-Propanol↗

PubMed2000

Bioavailability of ibuprofen from matrix mini-tablets based on a mixture of starch and microcrystalline wax.

The bioavailability of ibuprofen from matrix mini-tablets based on microcrystalline wax and a starch derivative was tested. An oral dose of 300 mg of ibuprofen was administered to healthy volunteers (n=8) in a randomized cross-over study design either as a commercial matrix formulation (Ibu-Slow 600) or as mini-tablets (filled into hard gelatin capsules). The mini-tablets consisted of 60% ibuprofen, 15% Paracera M (wax), 22.5% DDWM (starch) and 2.5% triacetin (lubricant). t50% of the in vitro release was 4.5 and 5 h for the mini-tablet and Ibu-slow formulations, respectively. Both formulations behaved in vivo as sustained-release formulation; their HVDt50%Cmax value was determined at 5.6 and 5.1 h for the mini-tablet and Ibu-slow formulations, respectively. A significantly higher value of Cmax was seen for the mini-tablet formulation, resulting in a relative bioavailability of 116 +/- 22.6% compared to the Ibu-slow matrix. These data demonstrate that the experimental mini-tablets can be used to formulate sustained-release dosage forms.

Adult↗

PubMed2000

Optimisation of an in vitro procedure for the determination of the enzymatic inhibition potency of multifunctional polymers.

An in vitro procedure for the determination of the inhibition potency of multifunctional polymers towards the proteolytic enzyme trypsin was optimised. Carbopol((R)) 934P was used as the reference polymer. The enzymatic reaction was optimised and the HPLC method was validated. The optimal substrate concentration and enzymatic activity were determined aiming at extracting the linear or steady-state part of the metabolite concentration versus time curve of the enzymatic degradation reaction. A substrate concentration of 20 mmol/l N-alpha-benzoyl-L-arginine-ethylester and an enzymatic activity of 30 enzymatic units trypsin/ml were used. The degree of trypsin inhibition was expressed by the inhibition factor (IF), defined as the ratio of the enzymatic reaction rate without a polymer (control) to the reaction rate in the presence of a polymer. During the optimisation of the trypsin inhibition assay, formation of an ion complex between the substrate and the poly(acrylic acid) was observed. The complex formation was concentration dependent, but the influence on the enzymatic reaction was negligible as long as an excessive substrate concentration was present in the reaction medium. The optimised method allows to characterize, evaluate and compare the in vitro trypsin inhibition strength for most multifunctional polymers.

Acrylic Resins↗

PubMed2000

A validated HPLC method for the determination of thiazinamium methylsulphate in pharmaceutical preparations.

The phenothiazine derivative thiazinamium methylsulphate is a drug with antihistaminic and anticholinergic properties, often used in some types of obstructive lung diseases. Because there is a lack of chromatographic data available for its determination, the objective of the present investigation was to develop a sensitive and rapid HPLC method for the quantitative estimation of thiazinamium methylsulphate in a pharmaceutical dosage form, applicable to routine analysis. The drug was chromatographed on a C18-reversed phase system applying a Licrocart column (LiChrospher 100 RP 18, 125 x 4 mm) with a mobile phase consisting of acetonitrile-water (3:7, v/v), employing as ion-pairing agent octanesulphonic acid sodium salt (20 mM) together with N,N-dimethyloctylamine (20 mM), adjusted to pH 3. Detection occurred at 254 nm. Propylparaben was used as an internal standard. The method was applied to solutions for intramuscular injection containing thiazinamium methylsulphate (65 mg/2 ml). Since little sample preparation is required, most analyses can be carried out within 15 min. The optimized method was validated and provided acceptable results with respect to linearity (r = 0.9999), precision and accuracy in the concentration range of 26-78 microg/ml. The proposed method is presently employed to investigate the stability of thiazinamium methylsulphate in solutions for intramuscular injection in the presence of anti-oxidizing agents.

Chromatography, High Pressure Liquid↗