Biomedical subjects

J T Czernuszka

Publications and source records attributed to J T Czernuszka.

8 recordsLinked to original sources

PubMed2006

Collagen-hydroxyapatite composites for hard tissue repair.

Bone is the most implanted tissue after blood. The major solid components of human bone are collagen (a natural polymer, also found in skin and tendons) and a substituted hydroxyapatite (a natural ceramic, also found in teeth). Although these two components when used separately provide a relatively successful mean of augmenting bone growth, the composite of the two natural materials exceeds this success. This paper provides a review of the most common routes to the fabrication of collagen (Col) and hydroxyapatite (HA) composites for bone analogues. The regeneration of diseased or fractured bones is the challenge faced by current technologies in tissue engineering. Hydroxyapatite and collagen composites (Col-HA) have the potential in mimicking and replacing skeletal bones. Both in vivo and in vitro studies show the importance of collagen type, mineralisation conditions, porosity, manufacturing conditions and crosslinking. The results outlined on mechanical properties, cell culturing and de-novo bone growth of these devices relate to the efficiency of these to be used as future bone implants. Solid free form fabrication where a mould can be built up layer by layer, providing shape and internal vascularisation may provide an improved method of creating composite structures.

Animals↗

PubMed2003

Making tissue engineering scaffolds work. Review: the application of solid freeform fabrication technology to the production of tissue engineering scaffolds.

Tissue engineering is a new and exciting technique which has the potential to create tissues and organs de novo. It involves the in vitro seeding and attachment of human cells onto a scaffold. These cells then proliferate, migrate and differentiate into the specific tissue while secreting the extracellular matrix components required to create the tissue. It is evident, therefore, that the choice of scaffold is crucial to enable the cells to behave in the required manner to produce tissues and organs of the desired shape and size. Current scaffolds, made by conventional scaffold fabrication techniques, are generally foams of synthetic polymers. The cells do not necessarily recognise such surfaces, and most importantly cells cannot migrate more than 500 microm from the surface. The lack of oxygen and nutrient supply governs this depth. Solid freeform fabrication (SFF) uses layer-manufacturing strategies to create physical objects directly from computer-generated models. It can improve current scaffold design by controlling scaffold parameters such as pore size, porosity and pore distribution, as well as incorporating an artificial vascular system, thereby increasing the mass transport of oxygen and nutrients into the interior of the scaffold and supporting cellular growth in that region. Several SFF systems have produced tissue engineering scaffolds with this concept in mind which will be the main focus of this review. We are developing scaffolds from collagen and with an internal vascular architecture using SFF. Collagen has major advantages as it provides a favourable surface for cellular attachment. The vascular system allows for the supply of nutrients and oxygen throughout the scaffold. The future of tissue engineering scaffolds is intertwined with SFF technologies.

Biocompatible Materials↗

PubMed2003

Novel collagen scaffolds with predefined internal morphology made by solid freeform fabrication.

Novel collagen scaffolds possessing predefined and reproducible internal channels with widths of 135 microm and greater have been produced. The process employed to make the collagen scaffold utilises a sacrificial mould, manufactured using solid freeform fabrication technology, and critical point drying technique. A computer aided design (CAD) file of the mould to be produced is created. This mould is manufactured using a phase change ink-jet printer. A dispersion of collagen is then cast into the mould and frozen. The mould is dissolved away with ethanol and the collagen scaffold is then critical point dried with liquid carbon dioxide. The effect of processing on the tertiary structure of collagen is assessed by monitoring the wavenumber of the N-H stretching vibration peak using Fourier transform infra-red spectroscopy and it is found that processing does not denature the collagen. Ultraviolet-visual spectroscopy was used to detect the presence of any contamination from the sacrificial mould on the collagen. The ability to use computer aided design and manufacture (CAD/CAM) provides a route to optimise scaffold designs using collagen in tissue engineering applications.

Animals↗

PubMed2001

A simple method for orienting silk and other flexible fibres in transmission electron microscopy specimens.

When microstructures are characterized by transmission electron microscopy (TEM), the interpretation of results is facilitated if the material can be sectioned in defined orientations. In the case of fibres, it is especially useful if transverse and longitudinal sections can be obtained reliably. Here we describe a procedure for orienting spider silk and other flexible fibres for TEM investigation. Prior to embedding in epoxy resin, the silk is wound around a notched support made from polyester film. No glue is required. After the silk and its supporting film have been embedded and the resin has been cured the film can be peeled away to reveal nearly perfectly orientated silk threads. Both transverse and longitudinal sections can then be cut with a microtome. The method can be extended to obtain sections at any intermediate orientation.

Animals↗

PubMed2001

Material removal during the sliding of hydroxyapatite against UHMWPE.

Hydroxyapatite has been rubbed against ultra-high-molecular-weight-polyethylene (UHMWPE) under calcium-containg aqueous solutions. Further, hardness tests were carried out in air and in calcium-containing solutions whose pH ranged from pH 5 to pH 9. Hardness was found to vary with pH with a peak at around pH 7, i.e. - a chemomechanical effect was observed. Wear tests consisted in sliding hydroxyapatite samples against a UHMWPE disk for eight hours when lubricated by the same solutions as those used for the hardness tests. Volume loss, pH and calcium concentration were measured for up to 8 hours of sliding. Linking wear tests results with hardness results and supersaturation levels, it was concluded that two wear mechanisms occurred. A chemical mechanism depending on supersaturation occurred at the early stages of sliding. The wear rate was essentially independent of hardness during this stage. After a few hours, depending on the supersaturation of the lubricant, the chemical mechanism turned into a chemomechanical mechanism dependant on hardness.

Biocompatible Materials↗

PubMed1999

Compositional and structural control in bone regenerative coatings.

The development of a low-temperature method of producing bioactive coatings for medical implants has been shown to bypass the problems associated with high temperature processing routes, in particular the appearance of amorphous phases and non-stoichiometric hydroxyapatite (HA), and delamination of the coating from the substrate. An electric field/aqueous solution technique for producing adherent, crack-free calcium phosphate coatings on titanium and stainless steel substrates is described. The characteristics of the coating are a function of electrode spacing, supersaturation, temperature and current and voltage conditions. Scanning electron microscopy (SEM) characterized the surface morphology of the coatings, which were shown to be HA. The possibility of producing a coating of carbonate-substituted HA having the same chemical composition as bone apatite, and forming at physiological temperatures, has also been demonstrated. The size of the microstructure decreased and the morphology changed as the carbonate ion concentration in the calcium and phosphate ion solution increased.

Journal Article↗

PubMed1998

Collagen--calcium phosphate composites.

There is a widespread clinical need for bone augmentation and replacement. The major solid phases of bone are collagen and calcium phosphate and a bone analogue based on these two constituents should have some useful properties. In this review this theme is developed and the properties of natural and naturally based composites are compared. Composites have been produced by the precipitation of calcium phosphates on to collagen and a summary of the methods and results from mechanical testing and scanning electron microscopy are presented. Composites with mechanical properties intermediate between cancellous and cortical bone have been produced. The review concludes by explaining some of the mechanical properties of the composites, using knowledge of the hierarchical architecture of bone and results from microscopical examination of the fractured composites.

Biomechanical Phenomena↗

PubMed1995

The effect of two types of cross-linking on some mechanical properties of collagen.

Samples of collagen were cross-linked by two different methods: (a) glutaraldehyde and (b) a combination of dehydrothermal treatment and cyanamide. The elastic modulus, the ultimate tensile strength (fracture stress), strain to failure, work of fracture, and fracture toughness were measured before and after cross-linking in ambient laboratory conditions, and during immersion in water. These tests were all performed over a range of strain rates. For collagen tested in the wet condition, it was found that cross-linking increased the elastic modulus from approximately 25-30 MPa, to between 55 and 60 MPa, but there was little effect on fracture stress, and strain to failure was reduced. The work of fracture of the collagen decreased on cross-linking. Cross-linking had the same effect on the elastic modulus, fracture stress, and strain to failure of dry collagen, but the work of fracture was unaffected. In conclusion, cross-linking increased the elastic modulus, reduced the strain to failure, and had little effect on the fracture stress of collagen under the present experimental conditions.

Biocompatible Materials↗