PubMed Health⌕ Search

Biomedical subjects

J Vierendeels

Publications and source records attributed to J Vierendeels.

5 recordsLinked to original sources

Optimisation of solute transport in dialysers using a three-dimensional finite volume model.

Dialyser manufacturers only provide limited information about mass removal under well-defined flow and solute conditions in commercially available dialysers for hemodialysis. This computational study aimed at assessing the solute transport efficiency in a dialyser for different geometries (fiber lengths and diameters). A three-dimensional finite volume model of a single fiber in a high flux polysulphone dialyser (Fresenius F60) was developed. Different equations describe blood and dialysate flow (Navier-Stokes), radial filtration flow (Darcy) and solute transport (convection-diffusion). Fluid and membrane properties were derived from in vitro and in vivo tests as well as from literature data. Urea (MW60) was used as marker to simulate small molecule removal, while middle molecule transport was modelled using vitamin B12 (MW1355) and inulin (MW5200). Keeping the fluid velocity in a single fiber constant, fiber diameter and length were changed in a wide range for evaluation of solute removal efficiency. Clearances were found enhanced by 13% (urea), 50% (vitamin B12) and 89% (inulin) for a fiber twice as long as a standard one and by 5.5% (vitamin B12) and 21% (inulin) for a fiber diameter of 150 mum instead of 200 mum. The impact of fiber dimensions was more pronounced for the middle molecules compared to urea.

Biological Transport↗

Validation of a fluid-structure interaction model of a heart valve using the dynamic mesh method in fluent.

Simulations of coupled problems such as fluid-structure interaction (FSI) are becoming more and more important for engineering purposes. This is particularly true when modeling the aortic valve, where the FSI between the blood and the valve determines the valve movement and the valvular hemodynamics. Nevertheless only a few studies are focusing on the opening and closing behavior during the ejection phase (systole). In this paper, we present the validation of a FSI model using the dynamic mesh method of Fluent for the two-dimensional (2D) simulation of mechanical heart valves during the ejection phase of the cardiac cycle. The FSI model is successfully validated by comparing simulation results to experimental data obtained from in vitro studies using a CCD camera.

Algorithms↗

Validation of the coupling of magnetic resonance imaging velocity measurements with computational fluid dynamics in a U bend.

Magnetic resonance imaging (MRI) can be used in vivo in combination with computational fluid dynamics (CFD) to derive velocity profiles in space and time and accordingly, pressure drop and wall shear stress distribution in natural or artificial vessel segments. These hemodynamic data are difficult or impossible to acquire directly in vivo. Therefore, research has been performed combining MRI and CFD for flow simulations in flow phantoms, such as bends or anastomoses, and even in human vessels such as the aorta, the carotid, and the abdominal bifurcation. There is, however, no unanimity concerning the use of MRI velocity measurements as input for the inflow boundary condition of a CFD simulation. In this study, different input possibilities for the inflow boundary conditions are compared. MRI measurements of steady and pulsatile flow were performed on a U bend phantom, representing the aorta geometry. PAMFLOW (ESI Software, Krimpen aan den Ussel, The Netherlands), an industrial CFD software package, was used to solve the Navier-Stokes equations for incompressible flow. Three main parameters were found to influence the choice of an inflow boundary condition type. First, the flow rate through a vessel should be exact, since it proves to be a determining factor for the accuracy of the velocity profile. The other decisive parameters are the physiology of the flow profile and the required computer processing unit time. Our comparative study indicates that the best way to handle an inflow boundary condition is to use the velocities measured by MRI at the inflow plane as being fixed velocities. However, before using these MRI velocity data, they first should be corrected for the partial volume effect by filtering and second scaled in order to obtain the correct flow rate. This implies that a reliable flow rate measurement absolutely is needed for CFD calculations based on MRI velocity measurements.

Aorta↗

Diastolic filling and pressure imaging: taking advantage of the information in a colour M-mode Doppler image.

The ability to derive non-invasively information on left ventricular diastolic function on one hand and pressure gradients on the other hand, makes Doppler ultrasound a very attractive tool in clinical practice. However, the limitations of the standard Doppler approaches in differentiating between normal and pseudonormal filling patterns, together with the limitations of the simplified Bernoulli equation for assessing pressure gradients, are well described. In this manuscript the role of colour M-mode Doppler echocardiography as a tool that can overcome these limitations is discussed. Relevant key concepts of the haemodynamics of left ventricular filling and its relationship with colour M-mode Doppler echocardiography are introduced.

Coronary Circulation↗

Left-ventricular pressure gradients: a computer-model simulation.

Both invasive left-ventricular pressure measurements and non-invasive colour M-mode echographic measurements have shown the existence of intraventricular pressure gradients (IVPGs) during early filling. The mechanisms responsible for these IVPG cannot be completely explained by the experiments. Therefore a one-dimensional numerical model is developed and validated. The model describes filling (both velocities and pressures) along a left ventricular (LV) base-apex axis. Blood-wall interaction in the left ventricle with moving boundaries is taken into account. The computational results for a canine heart indicate that the observed IVPGs during filling are the consequence of a complex interaction between, on the one hand, pressure waves travelling in the LV and, on the other hand, LV geometry, relaxation and compliance. The computational results indicate the pressure dependency of wavespeed (0.77-1.90 m-1 s) for different mean intraventricular pressures (0.88-5.00 mmHg) and IVPGs up to 2 mmHg, independent of the ratio of end systolic volume and equilibrium volume. Increasing relaxation rate not only decreases minimum basal pressure (2.8 instead of 3.6 mmHg) but also has a strong influence on the time delay between the minimum basal and apical pressures (14 ms instead of 49 ms). The results sustain the hypothesis that pressure-wave propagation determines IVPGs and that IVPGs are no proof of elastic recoil.

Blood Pressure↗