Biomedical subjects

J Yliruusi

Publications and source records attributed to J Yliruusi.

At least 19 recordsLinked to original sources

PubMed2004

Determination of tackiness of chitosan film-coated pellets exploiting minimum fluidization velocity.

The tackiness of aqueous chitosan film coatings and effects of anti-sticking agents on sticking tendency, were evaluated. A novel rapid method exploiting minimum fluidization velocity to determine tackiness was introduced and tested. The pressure difference over the miniaturized fluidized-bed was precisely recorded as a function of velocity of fluidization air. High molecular weight chitosan plasticized with glycerol was used as a film-forming agent. Magnesium stearate, titanium dioxide, colloidal silicon dioxide and glyceryl-1-monostearate (GMS) were studied as anti-sticking agents. Film coatings were performed in a miniaturized top-spray coater. The incorporation of anti-sticking agents led to a clear decrease in tackiness of the chitosan films, and magnesium stearate and GMS were shown the most effective. Film-coated pellets containing magnesium stearate and GMS as an anti-sticking agent were very easily fluidized (showing very low values of minimum fluidization velocity) and were thus classified as the best flowing and the least sticking samples. Both these additives were found anti-sticking agents of choice for aqueous chitosan film coatings. Determination of the experimental minimum fluidization velocity in a fluidized bed, is a useful and sensitive method of measuring the tackiness tendency of film-coated pellets.

Adhesiveness↗

PubMed2003

Effect of beta-sitosterol on precipitation of cholesterol from non-aqueous and aqueous solutions.

The aim of the present work was to study the solubility and phase behaviour of the beta-sitosterol-cholesterol mixed crystals in the presence and absence of water. Cholesterol, beta-sitosterol and 3:1, 1:1 and 1:3 mixtures of these were co-precipitated from acetone and acetone-water solutions. Precipitated crystals were analysed using powder X-ray diffraction (PXRD), differential scanning calorimetry (DSC), optical microscopy and Karl-Fischer titrimetry. The quantification of the sterols in solutions was preformed using GC-MS. The solubility of the sterols was mutually limiting. In the aqueous system, the solubility of both the sterols were significantly lower than in the absence of water, but the decrease in the solubility was considerably greater with the more hydrophobic beta-sitosterol. In the aqueous system, the total sterol solubility decreased with the increasing proportion of beta-sitosterol. The formation of new crystal structures, solid solutions of cholesterol and beta-sitosterol, was observed in non-aqueous as well as in aqueous environments except with the lowest cholesterol proportion in the system, in which case mixed crystals with eutectic behaviour were formed.

Acetone↗

PubMed2003

Enhanced stability of rubbery amylose-rich maize starch films plasticized with a combination of sorbitol and glycerol.

Well known aging problems with rubbery starch films are the migration of plasticizer and increased crystallinity leading to embrittlement. The effects of a combination of sorbitol and glycerol used as plasticizers on mechanical, moisture permeability and solid-state properties of rubbery amylose maize starch (Hylon VII) films were studied. The films were prepared by casting and were exposed to conditions of 25 degrees C/60% relative humidity (RH) and 40 degrees C/75% RH for 9 months. The starch films plasticized with a combination of sorbitol and glycerol (1:1) at equal amount to the polymer weight, were shown to be the most stable alternative of the studied films during the 9 months storage period. The water vapor transmission (WVTR) of the films did not change during the period of storage and neither did the elongation at break, but the tensile strength increased. X-ray diffraction (XRD) results showed that during storage no crystallization had occurred. The combination of sorbitol and glycerol prevented the migration of the plasticizer molecules out of the film.

Amylose↗

PubMed2003

Development and characterization of aqueous amylose-rich maize starch dispersion for film formation.

Development and characterization of amylose-rich starch dispersion for film forming was performed. The influence of dispersion preparation temperature on amylose-rich maize starch (Hylon VII) film formation, and the physical properties of the films were investigated. The film-forming ability of the dispersions was evaluated with free films plasticized with glycerol and sorbitol, and the films were prepared at an elevated temperature (70 degrees C) by a casting technique. The solid-state and particle properties of dispersions were investigated by means of X-ray diffraction (XRD), Fourier transform near infrared (FT-NIR) spectroscopy and laser diffraction particle size analysis. Free films were characterized with respect to their appearance, by FT-NIR spectroscopy, and by XRD. Mechanical stress-strain properties were also studied. Increasing the temperature of dispersion preparation results in higher crystallinity, thus affecting the film forming ability. Mechanically strong and elastic films can be formed from amylose-rich starch dispersion formed at 40 degrees C. The more crystalline precipitate complex (obtained at 80 degrees C) and the entirely amorphous gel (obtained at 10 degrees C) formed non-continuous and cloudy films. The better film-forming properties of the dispersion formed at 40 degrees C are probably due to the highly amorphous structure and smaller particle size. The study shows the possibility of using ambient tempered amylose-starch dispersion for film forming.

Amylose↗

PubMed2003

Development of indomethacin Carbopol ETD 2001 gels and the influence of storage time and temperature on their stability.

We investigated the development of a topical indomethacin gel formulation of suitable consistency using Carbopol ETD 2001 as the gelling agent. Topical gel formulations containing 1% w/w indomethacin (IND), 1% w/w Carbopol ETD 2001 (C2001), 1% of trethanolamine (TEA), 30% hexylene glycol (HG) and 10% polyethylene glycol (PEG 300) were prepared with excipients Tween 80, PVP 25, both Tween 80 and PVP 25 or neither agent. These four gel formulations were tested after a period of 1 and 4 weeks at storage temperature of 6 degrees C, 20 +/- 2 degrees C and 45 degrees C. Physical evaluation of the stability of these gels was carried out by microscopic and rheological tests, measurement of pH and by visual inspection. Rheological properties were studied using the cone and plate method at shear rates of 600 to 6000 1/s. Viscosities corresponding to shear rates were also calculated. Our results indicated that C2001 could be used as a gelling agent for IND in topical preparations. IND-C2001 gels were clear and exhibited an acceptable appearance; gel behaviour was non-Newtonian and pseudoplastic. The addition of either Tween 80 or PVP 25 to the base gel formulation significantly increased the shear stresses and viscosity of the gels. These novel formulations exhibited good physical stability throughout the 4-week examination periods as inferred from pH measurements and microscopic examination. Additionally, the non-Newtonian pseudoplastic behaviour of the gels was maintained throughout storage, with only a minimal decrease in gel viscosity after 4 weeks. Differences in consistencies of the four formulations, although initially apparent, were no longer evident after 4 weeks of storage for all temperature conditions examined. Gels stored at high temperature (45 degrees C) developed a dark yellow color and decreased in viscosity compared to other storage temperature.

Acrylic Resins↗

PubMed2002

Amylopectin as a subcoating material improves the acidic resistance of enteric-coated pellets containing a freely soluble drug.

The effect of an aqueous amylopectin subcoating on the acidic resistance and dissolution behaviour of enteric-coated pellets was studied. Freely water-soluble riboflavin sodium phosphate (RSP) was used as a model drug, and microcrystalline cellulose (MCC) and lactose as fillers in the pellet cores. The pellets were subcoated with 5% aqueous amylopectin solution or with 5% hydroxypropyl methylcellulose (HPMC) solution, and subsequently film-coated with aqueous dispersion of cellulose acetate phthalate (CAP). Drug release of enteric-coated pellets was investigated by confocal laser scanning microscopy (CLSM). Dissolution tests showed that amylopectin subcoating improved the acidic resistance of the enteric-coated pellets in 0.1 N hydrochloric acid (HCl) compared with HPMC subcoating. As the amylopectin subcoating load was increased to 4% and the aqueous CAP coating load to 35%, the coated pellets resisted in 0.1 N HCl solution for approximately 1 h (the amount of drug released was below 10%), and they dissolved in the SIF without enzymes in less than 10 min. Confocal microscopy images and profiles of mean fluorescence intensities of RSP (obtained in the range of the interface of the pellet core and the film and the film coating surface) showed consistent results with dissolution tests. It seems that amylopectin subcoating can prevent the influx of the dissolution medium into the pellet core, and thus decrease the premature dissolution and release of the drug from the enteric-coated pellets in 0.1 N HCl solution. The drug release mechanism appeared to be osmotically driven release, and followed by diffusion through the polymer film.

Acids↗

PubMed2002

Diffusion of a freely water-soluble drug in aqueous enteric-coated pellets.

The effects of filler used in the pellet cores (ie, waxy cornstarch or lactose) and the enteric film coat thickness on the diffusion and dissolution of a freely soluble drug were studied. Two kinds of pellet cores containing riboflavin sodium phosphate as a model drug, microcrystalline cellulose (MCC) as a basic filler, and waxy cornstarch or lactose as a cofiller were film coated (theoretically weight increase 20% or 30%) with an aqueous dispersion of cellulose acetate phthalate (CAP). The diffusion of riboflavin sodium phosphate in aqueous enteric-coated pellets was investigated using noninvasive confocal laser scanning microscopy (CLSM). The in vitro release tests were performed using a USP apparatus I (basket method). Diffusion of drug from the core to the film coat was found to be greater with lactose-containing pellets than with waxy cornstarch-containing pellets. The dissolution test showed that 30% enteric-coated waxy cornstarch pellets had a good acidic resistance in 0.1 N HCl solution for at least 1 hour, while the other enteric pellet formulations failed the test. The waxy cornstarch-containing enteric pellets dissolved at SIF in less than 10 minutes. Confocal images of film-coated pellets showed that waxy cornstarch-containing pellets had less drug dissolved than respective lactose-containing pellets. The observations were further confirmed by measurement of fluorescence intensity of riboflavin sodium phosphate in the film coat. The dissolution test was consistent with the confocal microscopy results. In conclusion, waxy cornstarch as a cofiller in the pellet cores minimizes premature drug diffusion from the core into the film coat layer.

Diffusion↗

PubMed2002

Pluronic F-127 gels as a vehicle for topical formulations of indomethacin and rheological behaviour of these formulations.

Topical gel formulations containing a non-steroidal anti-inflammatory drug, indomethacin (IND), were prepared using 20% w/w Lutrol PF-127 as a gel-forming agent, and 16, 20 and 24% w/w Hexylene glycol (HG) or polyethylene glycol 300 (PEG) as solvents. 1% w/w Tween 80 and 1% w/w PVP 25 were added as excipients. The effects of the amounts of solvent and excipients on the physical characteristics of IND gel such as consistency, appearance, crystallization, pH and viscosity were studied. The results indicated that 1% w/w IND is able to form a structural gel. The viscosity values were calculated from the rheograms which were determined by a Haake Rotovisco sensor at a shear rate of 10,000 l/s. Viscosities corresponding to shear rates of 1000, 3000, 6000 and 9000 l/s were also calculated. Yield points were approximated from the rheograms. Although all IND gels maintained their pseudoplastic flow behaviour, their viscosities decreased markedly with increasing shear rates. Furthermore, increasing the amount of HG or PEG gave a more viscous gel except for the 24 w/w% HG gels which turned a jelly with or without either Tween or PVP. The difference in viscosities was explained by the changes in the gel compositions. 20% of PEG-1% PVP ranked first in viscosity followed by 16% PEG-1% PVP, 16% PEG-1% Tween, 24% PEG, 20% PEG-1% Tween and 16% HG-1% PVP. The results indicate that the excipients influence the physical characteristics of the gels. The optimum concentration for gels manifesting as strength of gel was 20% PEG in combination with 1% PVP which had the highest viscosity and yield value at a low shear rate.

Administration, Topical↗

PubMed2002

Influence of storage time and temperature on the stability of indomethacin Pluronic F-127 gels.

The stability of 20 topical gel formulations containing drug, 1% w/w indomethacin (IND), and 20% w/w Pluronic (PF-127) as a gel-forming agent, hexylene glycol (HG) and polyethylene glycol 300 (PEG) in different amounts (16, 20 and 24% w/w) as solvents and 1% w/w polyvinyl pyrrolidone (PVP, K-25) and Tween as excipients was determined by appearance and consistency of the gels, microscopy, pH and rheological measurements after 1 and 4 weeks storage, at 6 degrees C, 20 +/- 2 degrees C and 45 degrees C. Viscosity values were determined from rheograms by a Haake Rotovisco sensor at shear rates of 1000 to 10,000 l/s. The relationship between effectors (temperature and storage time) and response (viscosity) was determined using multiple regression analysis. All formulations were stable at room temperature (20 +/- 2 degrees C). The consistency of the gels containing HG and PEG decreased during storage at 6 degrees C. Storing the gels at 6 degrees C resulted in the precipitation of IND, but when PVP was incorporated into the IND-PF-127 gels, the stability of the gels was improved. All IND gels sustained their pseudoplastic flow behaviour. The viscosity decreased as storage time increased. A statistically significant model was obtained, showing that the effect of storage temperatures on the viscosity was much less than the effect of storage time.

Chemical Phenomena↗

PubMed2001

Process analysis of fluidized bed granulation.

This study assesses the fluidized bed granulation process for the optimization of a model formulation using in-line near-infrared (NIR) spectroscopy for moisture determination. The granulation process was analyzed using an automated granulator and optimization of the verapamil hydrochloride formulation was performed using a mixture design. The NIR setup with a fixed wavelength detector was applied for moisture measurement. Information from other process measurements, temperature difference between process inlet air and granules (T(diff)), and water content of process air (AH), was also analyzed. The application of in-line NIR provided information related to the amount of water throughout the whole granulation process. This information combined with trend charts of T(diff) and AH enabled the analysis of the different process phases. By this means, we can obtain in-line documentation from all the steps of the processing. The choice of the excipient affected the nature of the solid-water interactions; this resulted in varying process times. NIR moisture measurement combined with temperature and humidity measurements provides a tool for the control of water during fluid bed granulation.

Excipients↗

PubMed2001

Rheological properties of creams with four different surfactant combinations - effect of storage time and conditions.

Changes in the rheological properties of four o/w cream formulations differing in the combination of surfactants were studied. The non-ionic surfactants used were soybean derivatives, polyethylene glycol 10 and 25 soya sterol, and sorbitol derivatives, sorbitan monooleate and trioleate. Combinations of the soybean and sorbitol derivatives were used. The rheological properties were tested during a 28-day storage period at three different storage conditions (cold, room temperature and accelerated conditions). In addition to dynamic and static rheological tests, droplet size distributions and conductivities of the creams were also determined. The consistency of the creams containing polyethylene glycol 10 soya sterol decreased during storage. Despite the greatest decreases in consistency, the creams containing polyethylene glycol 10 soya sterol exhibited the most viscoelastic structures with linear viscoelastic behaviour. Storing the creams for 28 days in the three different storage conditions made the differences in the consistency of the formulations smaller. All three storage conditions were involved when the conditions of the most viscoelastic cream of each formulation was specified. In the case of linearly viscoelastically behaving creams containing polyethylene glycol 10 soya sterol, all the rheological tests correlated with the droplet size distributions and the conductivity tests.

Chemistry, Pharmaceutical↗

PubMed2001

Use of a capillary rheometer to evaluate the rheological properties of microcrystalline cellulose and silicified microcrystalline cellulose wet masses.

The influence of microcrystalline cellulose (MCC) type and water content on the rheological properties of the wet powder masses were studied using two different MCC grades (Avicel and Emcocel) and silicified microcrystalline cellulose (SMCC, Prosolv). A ram extruder was used as a capillary rheometer and unique flow curves for each cellulose grade and moisture content were derived. In addition, the elastic parameters of recoverable shear and compliance were determined. From different flow curve models evaluated, it was not possible to obtain clear evidence, which model best described the rheological properties of each cellulose grade at each water level. Furthermore, the residuals were shear rate dependent, which indicates that the models do not perfectly agree with physical properties of the wet masses. The elastic properties of wet masses increased with increasing water content and decreased with increasing shear stresses. SMCC grade proved to be more elastic than the simple MCC grades at each moisture content. Thus, the rheological properties of MCC and SMCC wet masses were different and changed with water content. Consequently, it was not possible to achieve similar rheological properties between different grades of cellulose by altering the water content of the wet mass.

Cellulose↗

PubMed2001

Novel identification of pseudopolymorphic changes of theophylline during wet granulation using near infrared spectroscopy.

The purpose of this study was to demonstrate the efficiency of near infrared (NIR) spectroscopy in studying the pseudopolymorphic changes and the state of water during the wet granulation process. Anhydrous theophylline was granulated in a planetary mixer using water as granulation liquid. NIR spectra and differential scanning calorimetric (DSC) and wide-angle X-ray scattering (WAXS) patterns of theophylline granules, anhydrous theophylline, and theophylline monohydrate were measured. At a low level of granulation liquid (0.3 mol of water per mole of anhydrous theophylline), water absorption maxima in the NIR region occurred first at around 1475 and 1970 nm. These absorption maxima were identical to those of theophylline monohydrate. At higher levels of granulation liquid (1.3-2.7 mol of water per mole of anhydrous theophylline), the increasing absorption maxima occurred at 1410 and 1905 nm due to OH vibrations of free water molecules. X-ray diffraction patterns confirmed the transformation of anhydrous theophylline to theophylline monohydrate during wet granulation. NIR spectroscopy was able to detect different states of water molecules during the wet granulation process faster and in a more flexible manner than conventional methods.

Calorimetry, Differential Scanning↗

PubMed2001

Characterization of microcrystalline cellulose and silicified microcrystalline cellulose wet masses using a powder rheometer.

A powder rheometer has been used to study the properties of wet powder masses and the results have been compared to the mixer torque rheometer (MTR). Two different microcrystalline cellulose (MCC) grades (Avicel and Emcocel) and silicified microcrystalline cellulose (SMCC, Prosolv) were used as model powders. The wet massing behaviour of one material (Prosolv) was studied by the powder rheometer using liquid addition experiments, while the rheological properties of wet granules were studied using both the powder rheometer and the MTR. In water addition measurements the torque behaved in a similar way to MTR measurements and the maximum value of ZTL (zero torque limit) was achieved at the capillary state of wet mass. The wet granules exhibited different behaviour in the powder rheometer and the MTR experiments, which indicates that these rheometers involve different shear forces or they measure different properties of the wet granules. Emcocel wet masses achieved the capillary state at lower liquid amount than Avicel and Prosolv masses, which indicates that Emcocel is not able to hold as much water in the internal structure as Avicel and Prosolv. The powder rheometer proved to be a sensitive piece of equipment, which can be used to study both dry and wet powder masses. It was able to distinguish wet granules from wet powder masses after liquid addition, whereas the MTR could not. However, before the powder rheometer can be properly utilised in wet powder mass studies, the problem of torque overload requires resolution.

Cellulose↗

PubMed2001

Influence of the centrifugal granulating process on the properties of layered pellets.

Drug-layered pellets based on microcrystalline cellulose (MCC) beads as substrates were prepared using a laboratory-scale centrifugal granulator. The effect of three independent process parameters (rotor rotation speed, slit air flow rate, and spray air rate) on responses describing the amount of drug loss during the process, amount of agglomerates, bulk density, flowability, friability, shape, and surface roughness were studied using a 3(3) full factorial experimental design. The variables studied were found to have a significant influence on the responses evaluated. Rotor rotation speed and slit air flow rate had a significant positive influence on the amount of drug loss during the process and the amount of agglomerates, whereas rotor rotation speed and spray air rate had the same effect on the bulk density, flowability, and the roundness of the pellets. The amount of agglomerates and the roundness value of the pellets were negatively affected by the spray air rate while the slit air flow rate showed the same effect on the bulk density and flow rate of the pellets. In addition to the main effects, there were some significant paired interactions between slit air flow rate and spray air rate as well as rotor rotation speed and slit air flow rate. Based on the results, the significance of these three parameters should be considered carefully for quality pellet preparation by the centrifugal granulating technique using MCC beads as substrates.

Cellulose↗

PubMed2001

Microcrystalline cellulose-water interaction--a novel approach using thermoporosimetry.

PURPOSE: To study the physical state of water in microcrystalline cellulose (MCC) and in silicified microcrystalline cellulose wet masses and the effect of granulation on different water fractions. METHODS: Thermoporosimetry, together with the solute exclusion technique, was used to measure different water fractions and pore size distributions of wet granules. To understand the effect of granulation on the physical state of water, both ungranulated and granulated wet masses were studied. In addition, dynamic and isothermal step melting procedures were compared. RESULTS: Four distinct fractions of water (nonfreezing, freezing bound, free, and bulk water) could be detected in MCC wet masses. Granulation decreased the volume of bulk water and increased the volume of freezing bound and free water. Consequently, granulated wet masses were able to hold more water inside the particles compared to ungranulated wet masses. Thus, granulation had a similar effect on MCC as beating has on cellulose fibers in the papermaking proces CONCLUSIONS: Thermoporosimetry and solute exclusion increased the understanding of MCC-water interaction and showed how the physical state of water in MCC wet masses changes during granulation.

Algorithms↗

PubMed2001

Characterization of wet massing behavior of silicified microcrystalline cellulose and alpha-lactose monohydrate using near-infrared spectroscopy.

The purpose of this study was to investigate the energetic state of water in silicified microcrystalline cellulose (SMCC) and alpha-lactose monohydrate wet masses using near-infrared (NIR) spectroscopy. The applicability of NIR spectroscopy to studying pharmaceutical wet masses at a wide moisture range was evaluated in comparison with mixer torque rheometry (MTR). With increasing moisture content changes in the physical properties of the samples resulted in an apparent increase in log (1/R) throughout the whole spectrum. The upward displacement of baseline and the relative height of water bands were greatest with materials that had a poor liquid-retention capacity. In the case of SMCC and 1:1 mixture of SMCC and alpha-lactose monohydrate, the height of the baseline-corrected water bands increased linearly at low moisture contents, thereafter achieving a plateau stage. According to the MTR results, the plateau stage of the band heights indicated a capillary state of liquid saturation. The second derivative spectrum was capable of distinguishing monohydrate, absorbed, and adsorbed water, which overlapped in the absorbance spectrum. When water was absorbed to the internal structure of the material (SMCC), the water bands were first seen at higher wavelengths, then followed by a shift to lower wavelengths. When water was only adsorbed onto the surface of the particles (glass ballotini), the water bands were seen directly in the region of bulk water.

Crystallization↗

PubMed2001

Corn starches as film formers in aqueous-based film coating.

The purpose of this study was to evaluate the film formation ability and mechanical stress-strain properties of aqueous native corn starches, using free films and film coatings applied to tablets. Free films were prepared from high-amylose corn (Hylon VII), corn and waxy corn starches, using sorbitol and glycerol as plasticizers. The tablets and pellets were film-coated using an air-suspension coater, and characterized with respect to the film coating surface topography, cross-sectional structure and thickness (SEM), and dissolution in vitro. The amylose content of the starch film formers affected both the tensile strength and the elongation. The elongations were under 5% for even the plasticized starches, and in most cases, no plasticization effect was seen by either of the plasticizers. Dissolution of native corn starch film-coated tablets (weight gain 1%) did not differ from uncoated ones. A notable delay in dissolution of the drug was found by increasing Hylon VII film coating thickness, suggesting controlled-release characteristics.

Amylose↗