Biomedical subjects

Jaroslaw Drelich

Publications and source records attributed to Jaroslaw Drelich.

4 recordsLinked to original sources

PubMed2006

Structural effects recorded for AFM tips interacting with individual nanoparticles and their clusters deposited on substrates.

Mica and alumina were coated with nanoparticles using aqueous suspensions while managing attractive substrate-particle electrostatic forces. Using nanoparticle-coated substrates, structural forces were measured for 10 nm silica particles deposited on the alumina substrate and 5-80 nm alumina particles on mica using an atomic force microscopy technique. For nanoparticles forming clusters, oscillation of structural forces was recorded with a periodicity that is close to the size of nanoparticles used. Positioning the AFM tip over the single particles allowed, on the other hand, the study of probe-nanoparticle colloidal forces.

Journal Article↗

PubMed2005

Spreading kinetics of water drops on self-assembled monolayers of thiols: significance of inertial effects.

Spreading of 5-15 microL water drops on self-assembled monolayers of 1-hexadecanethiol and 11-mercapto-1-undecanol, both homogeneous and mixed compositions, formed on gold-coated silicon wafers or glass slides was recorded with a high-speed video camera. The time (t) evolution of the drop base diameter (D) during spreading was analyzed by a power law-correlation: D approximately t(n). The n value was found to increase from n = 0.3-0.5 for water drops on hydrophobic surfaces characterized by the advancing water contact angle of thetaA = 94-104 degrees to n = 0.5-0.8 on less hydrophobic surfaces (thetaA = 45-66 degrees ). These experimental values were found to be of similar magnitude as the literature values reported for small drops and bubbles, which spread over a variety of different substrates including water and water-ethanol drops on self-assembled monolayers of alkylsilanes, air bubbles in water on glass, molten metals on solid metals and ceramics, hydrocarbon drops on water, and others. Inertial effects, which are often not accounted for in the analysis of spreading results, appear to have an impact on the spreading kinetics of small drops in at least the first few milliseconds of the spreading phenomenon.

Journal Article↗

PubMed2004

Determination of solid surface tension from particle-substrate pull-off forces measured with the atomic force microscope.

Atomic force microscopy (AFM) is capable of solid surface characterization at the microscopic and submicroscopic scales. It can also be used for the determination of surface tension of solids (gamma) from pull-off force (F) measurements, followed by analysis of the measured F values using contact mechanics theoretical models. Although a majority of the literature gamma results was obtained using either Johnson-Kendall-Roberts (JKR) or Derjaguin-Muller-Toporov (DMT) models, re-analysis of the published experimental data presented in this paper indicates that these models are regularly misused. Additional complication in determination of gamma values using the AFM technique is that the measured pull-off forces have poor reproducibility. Reproducible and meaningful F values can be obtained with strict control over AFM experimental conditions during the pull-off force measurements (low humidity level, controlled and known loads) for high quality substrates and probes (surfaces should be free of heterogeneity, roughness, and contamination). Any probe or substrate imperfections complicate the interpretation of experimental results and often reduce the quality of the generated data. In this review, surface imperfection in terms of roughness and heterogeneity that influence the pull-off force are analyzed based upon the contact mechanics models. Simple correlations are proposed that could guide in selection and preparation of AFM probes and substrates for gamma determination and selection of loading conditions during the pull-off force measurements. Finally, the possibility of AFM measurements of solid surface tension using materials with rough surfaces is discussed.

Journal Article↗

PubMed2004

Theoretical contact angles on a nano-heterogeneous surface composed of parallel apolar and polar strips.

Neumann-Good's parallel strip model (J. Colloid Interface Sci. 1972, 38, 341) was used to analyze the contact angle hysteresis for a liquid on a heterogeneous surface composed of alternatively aligned horizontal apolar (theta = 70 degrees ) and polar (theta = 0 degree ) strips. The critical size of the strip width, below which the contact angle hysteresis disappears, was determined on the basis of the analysis of the activation energy for wetting to be from 6 to 12 nm. This calculated value of the critical strip size is 1 order of magnitude smaller than that of 0.1 microm, which has been commonly considered as the limit of heterogeneity size causing the appearance of the contact angle hysteresis.

Journal Article↗