Biomedical subjects

Jef Adriaensen

Publications and source records attributed to Jef Adriaensen.

4 recordsLinked to original sources

PubMed2006

Novel generic UPLC/MS/MS method for high throughput analysis applied to permeability assessment in early Drug Discovery.

A novel generic ultra performance liquid chromatography-tandem mass spectrometric (UPLC/MS/MS) method for the high throughput quantification of samples generated during permeability assessment (PAMPA) has been developed and validated. The novel UPLC/MS/MS methodology consists of two stages. Firstly, running a 1.5min isocratic method, compound-specific multiple reaction monitoring (MRM) methods were automatically prepared. In a second stage, samples were analyzed by a 1.5min generic gradient UPLC method on a BEH C18 column (50mmx2.1mm). Compounds were detected with a Waters Micromass Quattro Premier mass spectrometer operating in positive electrospray ionization using the compound-specific MRM methods. The linearity for the validation compounds (caffeine, propranolol, ampicillin, atenolol, griseofulvin and carbamazepine) typically ranges from 3.05nM to 12,500nM and the limits of detection for all generically developed methods are in the range between 0.61nM and 12nM in an aqueous buffer. The novel generic methodology was successfully introduced within early Drug Discovery and resulted in a four-fold increase of throughput as well as a significant increase in sensitivity compared to other in-house generic LC/MS methods.

Ampicillin↗

PubMed2006

Hot stage extrusion of p-amino salicylic acid with EC using CO2 as a temporary plasticizer.

The aim of the current research project was to explore the possibilities of combining pressurized carbon dioxide with hot stage extrusion during manufacturing of solid dispersions of the thermally labile p-aminosalicylic acid (p-ASA) and ethylcellulose 20cps (EC 20cps) and to evaluate the ability of the pressurized gas to act as a temporary plasticizer. The thermal stability of the p-ASA was investigated using DSC, TGA and HPLC. The compound decomposes completely upon melting. Below 110 degrees C and under atmospheric conditions, the compound is thermally stabile for 10min. Pressurized carbon dioxide was injected into a Leistritz Micro 18 intermeshing co-rotating twin-screw melt extruder using an ISCO 260D syringe pump. Carbon dioxide acted as plasticizer for p-ASA/EC 20cps, reducing the processing temperature during the hot stage extrusion process. HPLC showed that without carbon dioxide injection, approximately 17% of p-ASA degraded, while less than 5% degraded with CO(2) injection. The experiments clearly showed that injecting pressurized carbon dioxide broadens the application of hot stage extrusion to thermally labile compounds in a one step process.

Aminosalicylic Acid↗

PubMed2005

Preparation and physicochemical characterization of biodegradable nerve guides containing the nerve growth agent sabeluzole.

The objective of this study was to develop and characterize a biodegradable drug-loaded nerve guide for peripheral nerve regeneration. Sabeluzole, a nerve growth agent, was selected as model compound. Four biodegradable polymers were selected for this study: a copolymer of polylactic acid and polycaprolactone (PCL); a copolymer of polyglycolic acid and polycaprolactone PCL; a copolymer of PCL/polydioxanone (PDO) and PDO. Placebo and drug loaded nerve guides were obtained by melt compression and melt extrusion. It was observed that melt compression and melt extrusion are feasible techniques to prepare the nerve guides. Based on the physicochemical characterization, all samples show absence of crystalline sabeluzole, indicating the formation of an amorphous dispersion. The in vitro release measurements show that the release of sabeluzole is complete, reproducible and can be controlled by the proper selection of the polymer. The release mechanism for all samples follows Fickian release behaviour.

Absorbable Implants↗

PubMed2005

The effect of pressurized carbon dioxide as a temporary plasticizer and foaming agent on the hot stage extrusion process and extrudate properties of solid dispersions of itraconazole with PVP-VA 64.

The aim of the current research project was to explore the possibilities of combining pressurized carbon dioxide with hot stage extrusion during manufacturing of solid dispersions of itraconazole and polyvinylpyrrolidone-co-vinyl acetate 64 (PVP-VA 64) and to evaluate the ability of the pressurized gas to act as a temporary plasticizer as well as to produce a foamed extrudate. Pressurized carbon dioxide was injected into a Leistritz Micro 18 intermeshing co-rotating twin-screw melt extruder using an ISCO 260D syringe pump. The physicochemical characteristics of the extrudates with and without injection of carbon dioxide were evaluated with reference to the morphology of the solid dispersion and dissolution behaviour and particle properties. Carbon dioxide acted as plasticizer for itraconazole/PVP-VA 64, reducing the processing temperature during the hot stage extrusion process. Amorphous dispersions were obtained and the solid dispersion was not influenced by the carbon dioxide. Release of itraconazole from the solid dispersion could be controlled as a function of processing temperature and pressure. The macroscopic morphology changed to a foam-like structure due to expansion of the carbon dioxide at the extrusion die. This resulted in increased specific surface area, porosity, hygroscopicity and improved milling efficiency.

Acrylates↗