Biomedical subjects
Publications and source records attributed to Jia-Ming Liu.
A new technique of dual-frequency Doppler-lidar measurement is investigated. This technique is based on the use of a coherently locked, tunable, dual-frequency laser source and is shown to accurately measure velocities as small as 26 mum/s. It is generated by exploiting the nonlinear dynamics of a semiconductor laser through a proper combination of optical injection and operating conditions.
A new solid substrate-room temperature phosphorescence (SS-RTP) method for the determination of trace manganese (II) has been established. It bases on the fact that fullerol (R) emits strong and stable room temperature phosphorescence (RTP) on filter paper substrate. H2O2 can oxidize R to cause the SS-RTP quenching. But manganese (II) can obstruct H2O2 to oxidize R, and enhance the RTP of R. alpha,alpha'-Bipyridine (Bipy) can sensitize the RTP. After adding Bipy, the DeltaI(p) enhances 7 times than that without Bipy. Under the optimum conditions, the linear dynamic range of this method is 0.016-1.12 pg spot(-1) with a detection limit (L.D.) of 4.6 fg spot(-1) (m(Mn(2+) is the absolute mass of Mn(2+)), and the regression equation of working curve is DeltaI(p)=25.20 + 63.55 m(Mn(2+) (pg spot(-1)), n=6, r=0.9983. For 0.016 and 1.12 pg spot(-1) Mn(2+), RSDS are 4.3 and 4.8%, respectively (n=7). This method has been applied to the determination of trace manganese (II) in actual sample with high sensitivity and good selection. And the reaction mechanism of SS-RTP is discussed.
In the presence of heavy atom perturber LiAc, the silicon dioxide nanoparticle containing rhodamine 6G (R) and dibromoluciferin (D) (R-D-SiO(2)) can emit strong and stable solid-substrate room temperature phosphorescence signal of R (lambda(ex)/lambda(em)=481/648 nm) and D (lambda(ex)/lambda(em)=457/622 nm) on the surface of acetyl cellulose membrane (ACM). R-D-SiO(2) is used to label triticum vulgare lectin (WGA). Then two types of affinity adsorption reactions, R-D-SiO(2)-WGA- alkaline phosphatase (ALP) (direct method) and WGA-ALP-WGA-R-D-SiO(2) (sandwich method), are carried out on ACM. The conditions and the analytical characteristics for the determination of ALP using affinity adsorption solid-substrate room temperature phosphorimetry (AA-SS-RTP) were studied. For a 0.40-microl drop of sample, results show that the detection limits of the sandwich method are 0.16 ag spot(-1)(457/622 nm) and 0.17 ag spot(-1)(481/648 nm), and the detection limits of the direct method are 0.41 ag spot(-1) (457/622 nm) and 0.44 ag spot(-1) (481/648 nm). The contents of ALP in human serum correlated well with those obtained by enzyme-linked immunoassay. This study shows that AA-SS-RTP whether by the sandwich method or the direct method, can combine very well the characteristics of both high sensitivity of SS-RTP and specificity of the immunoreaction. Simultaneously, whether the phosphorescence excitation/emission wavelength of either R or D in R-D-SiO(2) is chosen to determine ALP, this can promote the agility and widen the adaptability of AA-SS-RTP.
A new method for the determination of trace mercury by solid substrate-room temperature phosphorimetry (SS-RTP) quenching method has been established. In glycine-HCl buffer solution, xylenol orange (XO) can react with Sn4+ to form the complex [Sn(XO)6]4+. [Sn(XO)6]4+ can interact with Fin- (fluorescein anion) to form the ion associate [Sn(XO)6]4+.[(Fin)4]-, which can emit strong and stable room temperature phosphorescence (RTP) on polyamide membrane (PAM). Hg2+ can catalyze H2O2 oxidizing the ion association complex [Sn(XO)6]4+.[(Fin)4]-, which causes the RTP to quench. The DeltaIp value is directly proportional to the concentration of Hg2+ in the range of 0.016-1.6 fg spot(-1) (corresponding concentration: 0.040-4.0 pg ml(-1), 0.40 microl spot(-1)), and the regression equation of working cure is DeltaIp=10.03+83.15 m Hg2+ (fg spot(-1)), (r=0.9987, n=6) and the detection limit (LD) is 3.6 ag spot(-1)(corresponding concentration: 9.0 x 10(-15) g ml(-1), the sample volume: 0.4 microl). This simple, rapid, accurate method is of high selectivity and good repeatability, and it has been successfully applied to the determination of trace mercury in real samples. The reaction mechanism for catalyzing H2O2 oxidizing the ion association complex ([Sn(XO)6]4+.[(Fin)4]-) SS-RTP quenching method to determine trace mercury is also discussed.
A radio-over-fiber system uses light to carry a microwave subcarrier on optical fibers. The microwave is usually frequency modulated for wireless broadcasting. A conventional optical communication system usually operates at the baseband with amplitude modulation. The interface of the two systems thus needs an upconversion from the baseband to the microwave band with AM-to-FM transformation. An all-optical solution employing an optically injected semiconductor laser is investigated. The laser is operated in a dynamic state, where its intensity oscillates at a microwave frequency that varies with the injection strength. When the injection carries AM data, the microwave is frequency modulated accordingly. We demonstrate optical conversion from an OC-12 622-Mbps AM baseband signal to the corresponding FM microwave signal. The microwave is centered at 15.90 GHz. A bit-error rate of less than 10(-9) is measured.
A new method for the determination of trace selenium based on solid substrate-room temperature phosphorimetry (SS-RTP) has been established. This method was based on the fact that in HCl-KCl buffer solution, potassium chlorate could oxidize phenyl hydrazine to form chloridize diazo-ion after being heated at 100 degrees C for 20 min, and then the diazo-ion reacted with 1,2-dihydroxynaphthalene-3,6-disulfonic acid to form red azo-compound which could emit strong room temperature phosphorescence (RTP) signal on filter paper. Selenium could catalyze potassium chlorate oxidizing the reaction between phenyl hydrazine and 1,2-dihydroxynaphthalene-3,6-disulfonic acid, which caused the sharp enhancement of SS-RTP. Under the optimum condition, the relationship between the phosphorescence emission intensity (DeltaIp) and the content of selenium obeyed Beer's law when the concentration of selenium is within the range of 1.60-320 fg spot-1 (or 0.0040-0.80 ng ml-1 with a sample volume of 0.4 microl). The regression equation of working curve can be expressed as DeltaIp=13.12+0.4839CSe(IV) (fg spot-1) (n=6), with correlation coefficient r=0.9991 and a detection limit of 0.28 fg spot-1 (corresponding to a concentration range of 7.0x10(-13) g ml-1 Se(IV), n=11). After 11-fold measurement, R.S.D. were 2.8 and 3.5% for the samples containing 0.0040 and 0.80 ng ml-1 of Se(IV), respectively. This accurate and sensitive method with good repeatability has been successfully applied to the determination of trace selenium in Chinese wolfberry and egg yolk with satisfactory results. The mechanism of the enhancement of phosphorescence was also discussed.
We theoretically investigate the nonlinear dynamics and synchronization properties between two mutually coupled semiconductor lasers units. Each unit can self-oscillate by means of delayed optoelectronic feedback loops. The mutual optoelectronic interactions between the laser units take into account the finite propagation time of the signals. Under perfectly symmetric conditions, we find different "death by delay" islands that persist for instantaneous coupling. The appearance of (zero lag) isochronous chaotic synchronization, under appropriate driving conditions, is another distinctive feature of the delayed feedback loops in the laser units. For slightly asymmetric operation, we obtain frequency locked bands (Arnold Tongue) whose width periodically changes with the coupling delay time.
Dissoluble manganese supramolecule containing rhodamine 6G luminescent particles (M2) are synthesized, based on dissoluble manganese supramolecule (M1) doping rhodamine 6G (R.6G), by crystalline method. The particle diameters of M1 and M2 determined by ETM are both of micron degree. M1 and M2 can emit solid substrate room temperature phosphorescence (SS-RTP) on filter paper. The transition probability from the singlet state (S1) to triplet state (T1) of the luminescent molecules was greatly enhanced, based on the increment of luminescent molecules for each spot and the heavy atom effect of certain amount of Pb2+. As a result, the phosphorescence intensity (Ip) of M2 was increased sharply, and the enhancing value of phosphorescence intensity (DeltaIp) is directly proportional to the concentration of Pb2+. Thus, a new method of SS-RTP enhancing for the determination of trace lead is established based on manganese supramolecule containing rhodamine 6G luminescent particles. The linear range of this method is 0.0040-0.400 pg spot-1 of Pb2+ (corresponding concentration, 0.01-1.0 ng mL-1; sample volume, 0.4 microL spot-1), with a detection limit (LD) of 0.0011 pg spot-1 (corresponding concentration, 2.8x10(-12) g mL-1 of Pb2+, n=11). For the working solutions containing 0.0040 and 0.40 ng mL-1 of Pb2+, they were determined repeatedly for seven times, respectively. The R.S.D.s were 3.2 and 3.8%, respectively. This method has good repeatability, sensitivity and high precision. It has been applied to the determination of trace lead in human hair and tea samples with satisfactory results.
Luminescent 20-nm silicon dioxide nanoparticles containing dibromofluorescein (D; particles denoted D-SiO(2)) were synthesized by the sol-gel method. In the presence of Pb(Ac)(2) as a heavy atom perturber, the particle can emit the intense and stable room temperature phosphorescence(RTP) signal on a polyamide membrane at the wavelength of lambdaex(max)/lambdaem(max) = 460/623 nm for D. Our research indicates that the specific immune reaction between goat-anti-human IgG antibody labeled with D-SiO(2) and human IgG can be carried out quantitatively on a polyamide membrane, and the phosphorescence intensity was evidently enhanced after the immunoreaction. Thus a new solid substrate-room temperature phosphorescence immunoassay (SS-RTP-IA) for determination of human IgG was established. The linear range of this method is 0.0624-20.0 pg spot(-1) of human IgG (corresponding to a concentration range of 0.156-50.0 ng ml(-1), sample volume: 0.40 microl spot(-1)). The regression equation of the working curve is DeltaIp = 94.39 + 17.00 m IgG (pg spot(-1)) (460/623 nm, r = 0.9998). Detection limit calculated as 3 Sb/k is 0.015 pg spot(-1). After elevenfold replicate measurement, RSD are 3.2% and 2.4% for samples containing 0.156 and 50.0 ng l(-1) IgG, respectively. This method is sensitive, accurate, and of high precision. And it has been applied to the determination of IgG in human serum with satisfactory results. Meanwhile, the mechanism of SS-RTP-IA based on an antibody labeled with nanoparticles containing dibromofluorescein luminescent molecules was discussed.
Silicon dioxide nano-particles, diameter 50 nm, containing morin (morin-SiO2) have been synthesized by the sol-gel method. They emit strong and stable room-temperature phosphorescence (SS-RTP) on filter paper as substrate, and bismuth can quench the intensity of the SS-RTP. On this basis a new morin-SiO2 solid-substrate room-temperature phosphorescence-quenching method has been established for determination of traces of bismuth. Reduction of phosphorescence intensity (DeltaI(p)) is directly proportional to the concentration of bismuth in the working range 0.16-14.4 ag spot(-1) (sample volume 0.40 muL spot(-1), corresponding to the concentration range 0.40-36.0 fg mL(-1)). The regression equation of the working curve is DeltaI(p)=14.86+5.279x[Bi3+] (ag spot(-1)) (n=6, r=0.9982). The detection limit of this method is 0.026 ag spot(-1) (corresponding to a concentration of 6.5 x 10(-17) g mL(-1)).This sensitive, reproducible and accurate method has been used for successful analysis of real samples.
A direct experimental observation of phase synchronization, amplitude synchronization, and frequency locking for the high-frequency broadband chaotic optical fields of the transmitter and the receiver is demonstrated in a fully optical system, where its chaotic optical wave form is generated through the high-speed nonlinearity of semiconductor lasers subject to optical injection. This experimentally achieved chaotic synchronous scenario is verified as identical chaos synchronization by observing several key characteristics of chaos synchronization in this system. The observation at the frequency detuning, the phase sensitivity, and the effect of mismatch at the injection strength from the master laser and match at the laser output power is in good agreement with the theoretical analysis of this system.
The dynamical behavior of two mutually coupled semiconductor lasers is studied. An optoelectronic coupling including a time delay in the propagation of the signals between the two lasers is considered. Starting from the appropriate rate equations for the photon and carrier densities, we investigate the stability of the fixed points and limit cycles of the system as a function of the coupling strength and the propagation time. From this analysis, a quasiperiodic route to chaos with boundary crisis events is identified as the responsible mechanism leading the system from regular to complex behavior. Several interesting phenomena are predicted for this system. Our analytical and numerical results are supported by experiments which are in good agreement with our predictions.
Luminescent 50-nm silicon dioxide nanoparticles containing both types of rhodamine 6G (R; particles denoted R-SiO2) were synthesized by the sol-gel method. In the presence of Pb(Ac)2 as a heavy atom perturber the particle can emit the intense and stable room-temperature phosphorescence (RTP) signal of R on a polyamide membrane, with lambda(ex)max/ lambda(em)max=470/635 nm for R. Our research indicates that the specific immune reaction between goat-anti-human IgG antibody labeled with R-SiO2 and human IgG can be carried out quantitatively on a polyamide membrane, and the phosphorescence intensity was enhanced after the immunoreaction. Thus a new method for solid-substrate room-temperature phosphorescence immunoassay (SS-RTP-IA) for determination of human IgG was established on the basis of antibody labeled with the nanoparticles containing binary luminescent molecules. The linear range of this method is 0.0624-20.0 pg spot(-1) of human IgG (corresponding to a concentration range of 0.156-50.0 ng mL(-1), sample volume 0.40 microL spot(-1)). The regression equations of the working curves are DeltaIp = 71.27+7.208 m(IgG) (pg spot(-1)) (r = 0.9996). Detection limits calculated as 3 Sb/k are 0.022 pg spot(-1). Compared with the same IA using fluorescein isothiocyanate (FITC) as the marker the new method was more sensitive and had a wider linear range. After elevenfold replicate measurement RSD are 4.5 and 3.6% for samples containing 0.156 and 50.0 ng mL(-1) IgG, respectively. This method is sensitive, accurate, and of high precision.
A solid substrate room temperature phosphorescence immunoassay (SS-RTP-IA) for the determination of human complement3 (C3) based on a sandwich type assay and a labelled avidin-biotin (LAB) type assay was described. The anti-human complement3 and avidin were labeled with eosin5-isothiocyanate. On a polyamide membrane (PM), SS-RTP signals (lambda(ex)/lambda(em) = 535/678 nm) of immune complexes obtained by both assays were linear with the concentration of complement3 in the range of 6.25-100 ng/ml. The detection limits are 1.37 ng/ml for sandwich assay and 2.74 ng/ml for labeled avidin-biotin assay. (For a sample volume of 0.4 microl per spot, the mass detection limits are 0.546 and 1.09 pg/spot, respectively. If the molecular weight of human complement3 is 185,000, the detection limits are 2.95 and 5.91 amol per spot.) The results of determination of complement3 in 20 human sera obtained by labeled avidin-biotin SS-RTP-IA are correlated well with those obtained by ELISA. This study shows that SS-RTP-IA by whichever direct, sandwich or labeled avidin-biotin type assay can combine very well the characteristics of both the high sensitivity of SS-RTP and specificity of the immunoreaction.
The medium (pH, organic solvents, cyclodextrin (CD) or surfactants) effects on the fluorescence of ciprofloxacin hydrochloride (CPFX.HCl) were studied in detail. It is found that the three acid constants of ciprofloxacin (CPFX) are near to each other. Therefore the relation curve between pH and fluorescence intensity has no strident change and keeps relative stable in the pH range of 2-7. When pH was in the range of 5.5-6.0, the fluorescence intensity of CPFX reached the max. The kind and amount of organic solvent added to the luminescent system have various effects. Ethanol quenched fluorescence and the fluorescence excitation wavelength is red shift at first and then blue shift. Acetone has complicated effects on the fluorescence properties of CPFX.HCl solution. The experiment result shows that acetone is really a quencher when its volume content in the system is from 0 to 20%, but when its content is 90%, the signal intensity is unexpectedly one and a half times as much as that of no acetone. This means that there is a strong interaction between the acetone and CPFX; CPFX.H(+) could be included into the gamma-CD but the capping effect is not notable. The effect of cationic surfactant cetyltrimethylammonium bromide and non-ionic surfactant TX-100 and TX-80 on CPFX fluorescence was unimpressive, but the anionic surfactant's effect is aberrant. The fluorescence intensity of CPFX.HCl solution experiences three stages of increasing, decreasing and increasing in turn, as sodium dodecyl sulfate is adding gradually. But for sodium lauryl sulfonate, there are only two stages of decreasing and increasing with the concentration increasing. It is problematic to illustrate clearly the effect mechanism of acetone and anionic surfactant at present. Undoubtedly, the experimental results in this paper should be useful in practice works and the research is worth studying still further.
A comparative study of the photoluminescence properties of three kinds of tetra-ring aromatic hydrocarbon (1-sodium pyrenesulphonate, benz[alpha]anthracene and chrysene) solution in the absence of any protecting medium is described. It was found that a room temperature phosphorescence signal with different intensities can be induced for these solutions, using only TlNO3 or KI as a heavy atom perturber (HAP) and Na2SO3 as a deoxygenator. An appropriate amount of organic solvent added to the systems of pyrene, benz[alpha]anthracene and chrysene is necessary for increasing the solubility and phosphorescence intensity, and the preferable solvent is acetonitrile. For the pyrene, pyrenesulphonate and chrysene systems, a delayed excimer fluorescence accompanied with the room temperature phosphorescence (RTP) emission can be observed, but that for benz[alpha]anthracene cannot. The ratio of delayed excimer fluorescence and phosphorescence signals for pyrene, pyrenesulphonate and chrysene systems can be controlled by adjusting the concentration of luminophor, kinds and amount of both organic solvents and HAP. Under the optimal conditions, the RTP signals are proportional to the concentration of the four aromatic hydrocarbons, which means that the RTP properties of the four tetra-ring aromatic hydrocarbons can be used for quantitative analysis.