Biomedical subjects

João T Cabral

Publications and source records attributed to João T Cabral.

5 recordsLinked to original sources

PubMed2006

Microfluidic approach for rapid multicomponent interfacial tensiometry.

We report a microfluidic instrument to rapidly measure the interfacial tension of multi-component immiscible liquids. The measurement principle rests upon the deformation and retraction dynamics of drops under extensional flow and was implemented for the first time in microfluidics (S. D. Hudson et al., Appl. Phys. Lett., 2005, 87, 081905 (ref. )). Here we describe in detail the instrument design and physics and extend this principle to investigate multicomponent mixtures, specifically two-component drops of adjustable composition. This approach provides fast real-time sigma measurements (on the order of 1 s), the possibility of rapidly adjusting drop composition and utilizes small sample volumes (approximately 10 microL). The tensiometer operation is illustrated with water drops and binary drops (water/ethylene glycol mixtures) in silicone oils. The technique should be particularly valuable for high-throughput characterization of complex fluids.

Equipment Design↗

PubMed2005

Solution of a field theory model of frontal photopolymerization.

Frontal photopolymerization (FPP) provides a versatile method for the rapid fabrication of solid polymer network materials by exposing photosensitive molecules to light. Dimensional control of structures created by this process is crucial in applications ranging from microfluidics and coatings to dentistry, and the availability of a predictive mathematical model of FPP is needed to achieve such control. Previous work has relied on numerical solutions in validating the model against experiments because of the intractability of the governing nonlinear equations. The present paper provides solutions to these equations in the general case in which the optical attenuation decreases (photobleaching) or increases (photodarkening) with photopolymerization. These solutions are of mathematical and physical interest because they support traveling waves of polymerization that propagate logarithmically or linearly in time, depending on the evolution of optical attenuation of the photopolymerized material.

Journal Article↗

PubMed2005

Microfluidic platform for the generation of organic-phase microreactors.

Rapid prototyping photolithography of a thiolene-based resin was used to fabricate microfluidic devices stable to aliphatic and aromatic organic solvents. The swelling of the cross-linked polymer matrix in various organic solvents was quantified, and the solvent resistance properties of these microfluidic devices are described. Discrete droplets of hexanes and toluene of uniform size were generated in microfluidic devices inside a water matrix containing SDS surfactant (SDS = sodium dodecyl sulfate). Variation of water and organic flow rates in the fluidic channels was used to control droplet size and separation. Droplet composition could be controlled by varying flow rates of two joined organic streams. Organic-phase synthetic reactions within the droplets were demonstrated with the bromination of alkenes inside benzene droplets.

Journal Article↗

PubMed2004

Frontal photopolymerization for microfluidic applications.

Frontal photopolymerization (FPP) offers numerous advantages for the rapid prototyping of microfluidic devices. Quantitative utilization of this method, however, requires a control of the vertical dimensions of the patterned resist material. To address this fundamental problem, we study the ultraviolet (UV) photopolymerization of a series of multifunctional thiolene resists through a combination of experiments and analytical modeling of the polymerization fronts. We describe this nonlinear spatio-temporal growth process in terms of a "minimal" model involving an order parameter phi(x, t) characterizing the extent of monomer-to-polymer conversion, the optical attenuation T(x, t), and the solid front position h(t). The latter exhibits an induction time (or equivalent critical UV dose) characterizing the onset of frontal propagation. We also observe a novel transition between two logarithmic rates of growth, determined by the Beer-Lambert attenuation constants mu(0) and mu(infinity) of the monomer and fully polymerized material, respectively. The measured frontal kinetics and optical transmission of the thiolene resist materials are consistent with our photopolymerization model, exhibiting both "photodarkening" and "photoinvariant" polymerization. This is apparently the first observation of photodarkening reported in FPP. On the basis of these results, multilevel fluidic devices with controlled height are readily fabricated with modulated illumination. A representative two-level microfluidic device, incorporating a chaotic mixer, a T junction, and a series of controlled flow constrictions, illustrates the practical versatility of this fabrication method.

Journal Article↗

PubMed2004

A new synthetic method for controlled polymerization using a microfluidic system.

While many parallel synthesis methods developed by the pharmaceutical and life science communities are being applied to polymer synthesis, there remains a need to construct "libraries" of polymeric materials that explore a wider range of polymer structures with accuracy, flexibility, and rapid, often small, changes. We report the use of microfluidics to create an environment for continuous controlled radical polymerization. Varying either the flow rate or the relative concentrations of reactants (i.e., stoichiometry) controls the molecular properties of the products. Molecular variables, here molecular weight, can then be varied continuously. Well-defined materials with narrow molecular weight distributions are produced inside the microfluidic reactor and are available for processing, such as further mixing, deposition, or coating on surfaces. Preliminary kinetic data appear to agree well with literature values reported for larger-scale reactions.

Journal Article↗