PubMed Health⌕ Search

Biomedical subjects

Joachim Kohn

Publications and source records attributed to Joachim Kohn.

At least 19 recordsLinked to original sources
PubMed2006

Selective protein adsorption on a phase-separated solvent-cast polymer blend.

Polymer-based biomedical devices are growing increasingly sophisticated as compositions evolve toward copolymers and blends in order to satisfy complex design criteria. Such polymers afford opportunities for both micro- and macrophase separation at nano- and micro-length scales and raise questions concerning the role of heterogeneous surface morphology on protein adsorption. Adsorbed protein layers play a critical role in mediating the interaction of cells with polymer surfaces, and both understanding and controlling protein adsorption is assuming greater significance in the development of surfaces with enhanced physiological compatibility. Here we study the short-time adsorption of ferritin, a model protein highly resistant to denaturation and easily imaged in the transmission electron microscope (TEM), onto a phase-separated homopolymer blend of polycaprolactone (PCL) and a polycarbonate derived from desaminotyrosyl-tyrosine dodecyl ester (PDTD). At physiological pH, ferritin selectively adsorbs onto the PDTD phase at a surface density approximately three times greater than that on the PCL phase. By decreasing the pH below ferritin's isoelectric point so its average charge becomes positive, the selective adsorption disappears and the surface density of adsorbed ferritin becomes independent of the phase separation. We attribute the selectivity to the electrostatic repulsion between ferritin and hydrolytically charged PCL, both of which will have a net negative charge at physiological pH. To perform these experiments, we solvent-cast ultrathin polymer films onto dissolvable salt substrates, and we characterize the morphology by TEM imaging and quantitative spatially resolved electron energy-loss spectroscopy (EELS). We find that the film morphology depends strongly on such processing-related variables as the solvent evaporation rate and the nature of the surface in contact with the polymer film during casting. The adsorption of ferritin depends on whether the film is phase-separated as well as to which surface of the film the protein solution is exposed, and these findings suggest that seemingly small variations in polymer processing that influence both the bulk and surface morphology can have a profound effect on the short-time protein adsorption.

Adsorption↗
PubMed2006

Minute changes in composition of polymer substrates produce amplified differences in cell adhesion and motility via optimal ligand conditioning.

We explored the interplay between substratum chemistry of polymeric materials and surface-adsorbed ligand concentration (human plasma fibronectin) in the control of cell adhesion and cell motility. We found that small changes in the chemical composition of a polymeric substratum had different effects on cellular motility--depending on the concentration of preadsorbed fibronectin. We used two tyrosine-derived polyarylates, poly(DTD diglycolate) and poly(DTD glutarate), as substrata for the seeding of NIH-3T3 fibroblasts. The only compositional difference between the two test polymers was that one single oxygen atom in the polymer backbone of poly(DTD diglycolate) had been substituted by a methylene group in the backbone of poly(DTD glutarate), The two polymers had closely matched hydrophobicity and physical properties. Flat, spin-coated surfaces of these polymers were pretreated with different concentrations of human plasma fibronectin (0-20 microg/ml). After seeding with NIH-3T3 fibroblasts, we examined the adhesion and motility behavior of these cells. We found that NIH-3T3 fibroblasts migrated significantly faster on poly(DTD diglycolate), but only when the polymer surfaces were pretreated with intermediate concentrations of fibronectin. Only at these intermediate levels of ligand conditioning, did the presence of an extra oxygen atom in the backbone of poly(DTD diglycolate) relative to poly(DTD glutarate) (i) alter the overall organization/concentration of the fibronectin; (ii) weaken cell attachment strength and inhibited excessive cell spreading; and (iii) promote cell motility kinetics. These findings indicate that the biological effect of minute changes in substratum chemistry is critically dependent on the level of surface-adsorbed cell-binding ligands.

Adsorption↗
PubMed2006

Cellular response to phase-separated blends of tyrosine-derived polycarbonates.

Two-dimensional thin films consisting of homopolymer and discrete compositional blends of tyrosine-derived polycarbonates were prepared and characterized in an effort to elucidate the nature of different cell responses that were measured in vitro. The structurally similar blends were found to phase separate after annealing with domain sizes dependent on the overall composition. The thin polymer films were characterized with the use of atomic force microscopy (AFM), water contact angles, and time-of-flight secondary ion mass spectrometry (TOF-SIMS) and significant changes in roughness were measured following the annealing process. Genetic expression profiles of interleukin-1beta and fibronectin in MC3T3-E1 osteoblasts and RAW 264.7 murine macrophages were measured at several time points, demonstrating the time and composition-dependent nature of the cell responses. Real-time reverse transcriptase polymerase chain reaction (RT-PCR) depicted upregulation of the fibronectin gene copy numbers in each of the blends relative to the homopolymers. Moreover, the interleukin-1beta expression profile was found to be compositionally dependent. The data suggest strongly that optimal composition and processing conditions can significantly affect the acute inflammatory and extracellular matrix production responses.

Animals↗
PubMed2006

Electrospun mat of tyrosine-derived polycarbonate fibers for potential use as tissue scaffolding material.

Desaminotyrosyl-tyrosine ethyl ester (DTE) and desaminotyrosyl-tyrosine (DT) were used as monomers in the synthesis of two tyrosine-derived polycarbonates: the slow degrading homopolymer poly(DTE carbonate) and the fast degrading co-polymer poly(DTE-co-20%DT carbonate). Ultrafine fibers of these polymers were successfully fabricated using an electrospinning process. The effects of some solution and process parameters (i.e., polymer concentration, electrostatic field strength and solvent system) on morphological appearance and diameters of the obtained fibers were investigated by scanning electron microscopy (SEM). Smooth fibers were obtained at high enough solution concentrations (i.e., 15 and 20% (w/v)). The average fiber diameter was found to increase with increasing polymer concentration and applied electrostatic field strength. The electrospinnability of poly(DTE-co-20%DT carbonate) in dichloromethane was enhanced when methanol was used as the co-solvent. In all of the conditions investigated, the average diameter of the obtained smooth fibers ranged between 1.9 and 5.8 microm. A qualitative assessment of an as-spun mat of poly(DTE carbonate) fibers as a tissue scaffolding material showed that three different cultured cell lines appeared to adhere and propagate well within the scaffold. For poly(DTE carbonate) exceptionally high cell densities could be achieved after 10 days of cell culture.

Animals↗
PubMed2005

pH triggered release of protective poly(ethylene glycol)-b-polycation copolymers from liposomes.

Triggered release of adsorbed polymers from liposomes enables protection against immune recognition during circulation and subsequent intracellular delivery of DNA. Polycationic blocks, poly[2-(dimethylamino) ethyl methacrylate] (DMAEMA) (0.8, 3.1, 4.9, or 9.8 kg/mol) or polylysine (K) (3 kg/mol), act as anchors for poly(ethylene glycol) (PEG) (2 or 5 kg/mol) protective blocks. In addition, a copolymer with 15 strictly alternating blocks of PEG (2 kg/mol) and cationic amine sites was evaluated as a protective coating. Incorporation of 1,2-dioleoyl-3-dimethylammonium-propane, a titratable lipid with a pKa of approximately 6.7, allows the liposome's net charge to increase as the pH shifts from 7.4 in the bloodstream to 5.5 in the endosome. The increased net liposome cationicity results in decreased cationic polymer adsorption. The EMPEG113-DMAEMA31 and EMPEG113-DMAEMA62 association constants decrease from 3.1 and 6.2 (mg/m(2))/(mg/ml) at pH 7.4 to 1.7 and 3.2 (mg/m(2))/(mg/ml) at pH 5.5, respectively. However, EMPEG45-DMAEMA5, EMPEG45-DMAEMA20, and EMPEG45-N-DP15 did not show a strong response to changes in pH. Cationic polymer adsorption exceeds calculated values for liposome neutralization, resulting in adsorption profiles in the brush regime.

Adsorption↗
PubMed2005

A computational approach to predicting cell growth on polymeric biomaterials.

A predictive model that can correlate the chemical composition of a biomaterial with the biological response of cells that are in contact with that biomaterial would represent a major advance and would facilitate the rational design of new biomaterials. As a first step toward this goal, we report here on the use of Logical Analysis of Data (LAD) to model the effect of selected polymer properties on the growth of two different cell types, rat lung fibroblasts (RLF, a transformed cell line), and normal foreskin fibroblasts (NFF, nontransformed human cells), on 112 surfaces obtained from a combinatorially designed library of polymers. LAD is a knowledge extraction methodology, based on using combinatorics, optimization, and Boolean logic. LAD was trained on a subset of 62 polymers and was then used to predict cell growth on 50 previously untested polymers. Experimental validation indicated that LAD correctly predicted the high and low cell growth polymers and found optimal ranges for polymer chemical composition, surface chemistry, and bulk properties. Particularly noteworthy is that LAD correctly identified high-performing polymer surfaces, which surpassed commercial tissue culture polystyrene as growth substratum for normal foreskin fibroblasts. Our results establish the feasibility of using computational modeling of cell growth on flat polymeric surfaces to identify promising "lead" polymers for applications that require either high or low cell growth.

Animals↗
PubMed2005

Formation of viscoelastic protein layers on polymeric surfaces relevant to platelet adhesion.

The hemocompatibility of biomaterials is highly dependent on the adhesion and activation of platelets. Surface-adsorbed fibrinogen has a dominant role in promoting platelet adhesion to artificial surfaces by binding glycoprotein IIb-IIIa (GPIIb-IIIa), the major platelet membrane receptor. Using quartz crystal microbalance with dissipation monitoring (QCM-D), we have investigated the material-dependent binding kinetics of purified GPIIb-IIIa to polymer-adsorbed fibrinogen. The following ranking of polymer-adsorbed mass (fibrinogen and GPIIb-IIIa) to test polymers could be established: poly[desaminotyrosyl-tyrosine ethyl (DTE) carbonate]/poly(lactide-co-glycolide)>poly[DTE co-5% poly(ethylene glycol) carbonate]. The QCM-D fibrinogen adsorption data were confirmed using an immunofluorescence assay. A synthetic RGD-containing peptide, but not a control peptide, inhibited GPIIb-IIIa binding to polymer-adsorbed fibrinogen, demonstrating the specificity of binding. Importantly, the binding efficiency of purified GPIIb-IIIa to polymer-adsorbed fibrinogen correlated with increased platelet adhesion in an in vitro model. Theoretical simulations using a Voight-based model provided quantitative data on the thickness and viscoelastic properties of the polymer-adsorbed protein layers. The precision of the modeling technique was limited with respect to the shear moduli values, leading to large variations. However, the other modeling parameters showed reproducible results. The thickness of both protein layers was polymer-dependent and ranged from 5 to 35 nm and the viscosity from 0.001 to 0.005 kg/ms, whereas the protein layer densities showed little differences between the test polymers. These results suggest that material-dependent changes in the thickness and viscoelastic properties of adsorbed fibrinogen-GPIIb-IIIa layers are crucial factors in the binding behavior of platelets to biomaterials.

Adsorption↗
PubMed2005

Degradable, drug-eluting stents: a new frontier for the treatment of coronary artery disease.

This article reviews the clinical use of stents in the treatment of coronary artery disease and the rationale for the use of degradable, drug-eluting polymer stents. The authors note the challenges of using off-the-shelf polymers for the development of degradable stents, as well as the interplay between polymer properties and a functional stent design. Drug-eluting metal stents are the most significant advancement in the treatment of coronary artery disease, and have significantly reduced the occurrence of in-stent restenosis after placement. Some regard drug-eluting metal stents as the final technologic advancement in the treatment of coronary artery disease, others consider the future development of degradable, drug-eluting stents as the next logical step.

Absorbable Implants↗
PubMed2004

Nontoxic block copolymer nanospheres: design and characterization.

Biodegradable polymers capable of self-assembly into hollow nanospheres of less than 100 nm have significant potential for biotechnology applications such as drug delivery and gene therapy. Here we describe the synthesis of a novel ABA-type triblock copolymer made from a hydrophobic tyrosine-derived core and two hydrophilic poly(ethylene glycol) end groups (poly(ethylene glycol)-block-oligo(desaminotyrosyltyrosine octyl ester suberate)-block-poly(ethylene glycol)). We describe the self-assembly of this triblock copolymer and characterize its particles as 100 nm size vesicular nanospheres. The vesicular nature of these particles was determined by light scattering and electron microscopy. The nanospheres did not exhibit any short-term cytotoxicity toward UMR-106 cells at a concentration up to 2 mg/mL.

Cell Line↗
PubMed2004

Poly(ethylene glycol) enhances cell motility on protein-based poly(ethylene glycol)-polycarbonate substrates: a mechanism for cell-guided ligand remodeling.

The regulation of cell motility on ligand-adsorbed poly(ethylene glycol) (PEG)-based polymeric biomaterials is governed by variables that are not well characterized. In this report, we examined keratinocyte migratory responsiveness to PEG-variant tyrosine-derived polycarbonates adsorbed with equivalent levels of the cell adhesion ligand, fibronectin. The equivalently adsorbed ligand adopted differential distributions, confirmed via atomic force microscopy, and the total number of exposed cell-binding domains (CBD), quantified through immunosorbent fluorometry, varied as a function of PEG concentration. Specifically, the CBD exposure was maximized at 4 mol % PEG and diminished at 8 mol % PEG, suggesting, based on our previous work (Tziampazis et al., Biomaterials 2000;21:511-520), that activation of cell adhesion and motility could be potentially promoted through increased CBD exposure at intermediate levels of PEG. This was confirmed through cell migration studies wherein cell speed values increased from 11 to 22 microm/h as the PEG concentration was increased from 0 to 4 mol %. Unexpectedly, however, high cell motility rates were sustained at 8 mol % PEG despite diminished levels of initial CBD exposure beyond 4 mol % PEG, suggesting that factors other than the initial CBD exposure may additionally have a role in activating cell migration at higher levels of PEG. Through studies of direct ligand mobility, cell-ligand-polymer interactions via atomic force microscopy, and CBD variation and integrin receptor roles in ligand remodeling, we offer evidence that cell motility is enhanced by a new mechanism for the regimen of higher PEG concentration: upon cell attachment and spreading, the ligand exhibits greater "slippage" at the polymer interface, and undergoes cell-engendered remodeling, which further activates cell motility, likely through enhanced exposure of hitherto encrypted sites for cell binding and signaling.

Antibodies↗
PubMed2004

Small changes in the polymer structure influence the adsorption behavior of fibrinogen on polymer surfaces: validation of a new rapid screening technique.

Numerous studies conclude that the selective adsorption of plasma proteins on materials contacting blood or tissue affects all subsequent interactions related to the biocompatibility of artificial surfaces. However, there are only a few studies available, which clearly demonstrate that there is a correlation between surface chemistry and selective protein adsorption. Detailed knowledge of such correlations would facilitate the design of biocompatible materials. In this study, a rapid, fluorescence-based, screening technique using a 384-well format for polymer-protein interactions was developed. The screening assay was used to measure the adsorption of human fibrinogen on 46 test polymers (44 polyarylates selected from a combinatorial library of tyrosine-derived polyarylates, and two lactide-based polymers). In this library of polyarylates, structural changes are generated by variations in either the polymer backbone or the polymer pendent chain. Although no overall trend between polymer hydrophobicity and fibrinogen adsorption could be identified using the entire set of test polymers (R(2) = 0.43), fibrinogen adsorption was clearly correlated with variations in the pendent chain structure. Thus, when the test polymers were grouped by backbone composition, increased hydrophobicity of the pendent chain was significantly correlated with reduced fibrinogen adsorption. The following R(2) coefficients within the polymer backbone groups were determined: 0.87 (diglycolates); 0.98 (glutarates); 0.73 (adipates); 0.87 (suberates); 0.67 (3-methyl-adipates). Our results demonstrate that it is possible to screen for protein-material interactions in a cost-effective fashion using a miniaturized immunofluorescence technique. Further, we demonstrate that small changes in chemical composition can significantly influence the adsorption of human fibrinogen on polymer surfaces. The lactide-based polymers were among those polymers exhibiting the highest tendency to adsorb fibrinogen. This information may be useful when polymers have to be selected for specific biomaterial applications.

Adsorption↗
PubMed2004

New approaches to biomaterials design.

The adoption of combinatorial and computational methods in biomaterials design is a highway towards the discovery and realization of tailored polymeric materials to satisfy the specific requirements of many diverse biomedical or prosthetic applications.

Biocompatible Materials↗
PubMed2003

A photo-crosslinked poly(vinyl alcohol) hydrogel growth factor release vehicle for wound healing applications.

The objective of this study was to develop and evaluate a hydrogel vehicle for sustained release of growth factors for wound healing applications. Hydrogels were fabricated using ultraviolet photo-crosslinking of acrylamide-functionalized nondegradable poly(vinyl alcohol) (PVA). Protein permeability was initially assessed using trypsin inhibitor (TI), a 21 000 MW model protein drug. TI permeability was altered by changing the solids content of the gel and by adding hydrophilic PVA fillers. As the PVA content increased from 10% to 20%, protein flux decreased, with no TI permeating through 20% PVA hydrogels. Further increase in model drug release was achieved by incorporating hydrophilic PVA fillers into the hydrogel. As filler molecular weight increased, TI flux increased. The mechanism for this is most likely an alteration in protein/gel interactions and transient variations in water content. The percent protein released was also altered by varying protein loading concentration. Release studies conducted using growth factor in vehicles with hydrophilic filler showed sustained release of platelet-derived growth factor (PDGF-beta,beta) for up to 3 days compared with less than 24 hours in the controls. In vitro bioactivity was demonstrated by doubling of normal human dermal fibroblast numbers when exposed to growth factor-loaded vehicle compared to control. The release vehicle developed in this study uses a rapid and simple fabrication method, and protein release can be tailored by modifying solid content, incorporating biocompatible hydrophilic fillers, and varying protein loading concentration.

Becaplermin↗
PubMed2003

Association of hydrophobically-modified poly(ethylene glycol) with fusogenic liposomes.

We present results on using cooperative interactions to shield liposomes by incorporating multiple hydrophobic anchoring sites on polyethylene glycol (PEG) polymers. The hydrophobically-modified PEGs (HMPEGs) are comb-graft polymers with strictly alternating monodisperse PEG blocks (M(w)=6, 12, or 35 kDa) bonded to C18 stearylamide hydrophobes. Cooperativity is varied by changing the degree of oligomerization at a constant ratio of PEG to stearylamide. Fusogenic liposomes prepared from N-C12-DOPE:DOPC 7:3 (mol:mol) were equilibrated with HMPEGs. Affinity for polymer association to liposomes increases with the degree of oligomerization; equilibrium constants (given as surface coverage per equilibrium concentration of free polymer) for 6 kDa PEG increased from 6.1+/-0.8 (mg/m(2))/(mg/ml) for 2.5 loops to 78.1+/-12.2 (mg/m(2))/(mg/ml) for 13 loops. In contrast, the equilibrium constant for distearoylphosphatidylethanolamine-poly(ethylene glycol) (DSPE-PEG5k) was 0.4+/-0.1 (mg/m(2))/(mg/ml). The multi-loop HMPEGs demonstrate higher levels of protection from complement binding than DSPE-PEG5k. Greater protection does not correlate with binding strength alone. The best shielding was by HMPEG6k-DP3 (with three 6 kDa PEG loops), suggesting that PEG chains with adequate surface mobility provide optimal protection from complement opsonization. Complement binding at 30 min and 12 h demonstrates that protection by multi-looped PEGs is constant whereas DSPE-PEG5k initially protects but presumably partitions off of the surface at longer times.

Adsorption↗
PubMed2003

Polymers derived from the amino acid L-tyrosine: polycarbonates, polyarylates and copolymers with poly(ethylene glycol).

The natural amino acid L-tyrosine is a major nutrient having a phenolic hydroxyl group. This feature makes it possible to use derivatives of tyrosine dipeptide as a motif to generate diphenolic monomers, which are important building blocks for the design of biodegradable polymers. Particularly useful monomers are desaminotyrosyl-tyrosine alkyl esters (abbreviated as DTR, where R stands for the specific alkyl ester used). Using this approach, a wide variety of polymers have been synthesized. Here, tyrosine-derived polycarbonates, polyarylates, and polyethers are reviewed with special emphasis on recent developments relating to cellular and in vivo responses, sterilization techniques, surface characterization, drug delivery, and processing and fabrication techniques. The commercial development of tyrosine-derived polycarbonates is most advanced, with one polymer, poly(DTE carbonate) (E=ethyl), being under review by the USA Federal Drug Administration.

Animals↗
PubMed2002

A synthetic polymer matrix for the delayed or pulsatile release of water-soluble peptides.

The design of a polymeric peptide release system with a controlled delay time and a burst-free pre-release phase is described. In general, the system consists of a blend of a tyrosine-derived polyarylate and a fast-degrading copolymer of lactic and glycolic acid (PLGA). Due to the peptide-like structure of the polyarylate backbone, peptide-polymer interactions prevented the release of peptide from neat polyarylate films. The addition of PLGA acts as a 'delayed' excipient: as PLGA degrades, it generates acidic degradation products that cause a drop in the internal pH of the polyarylate matrix. This drop in pH weakens the peptide-polymer interactions and causes the release of peptide to commence. The initial molecular weight of PLGA can be used to control the length of time before degradation occurs. Consequently, this parameter can also be used to control the duration of the delay period prior to peptide release. As a specific model system, blends of poly(DTH adipate) with three different copolymers of lactic and glycolic acid were prepared and used for the delayed release of Integrilin, a synthetic water-soluble heptapeptide (clinically used in antithrombic injections) that acts as a highly potent glycoprotein IIb/IIIa antagonist. Blends composed of a 1:1 weight ratio of poly(DTH adipate) and PLGA and containing Integrilin (15%, w/w) were prepared. In vitro release studies were conducted in phosphate buffered solution at 37 degrees C and the release of Integrilin was followed by HPLC. As the initial molecular weight of PLGA varied from 12000 to 62000, the duration of the delay period prior to release increased from 5 to 28 days.

Delayed-Action Preparations↗
PubMed2002

Biomaterials and scaffolds in reparative medicine.

Most approaches currently pursued or contemplated within the framework of reparative medicine, including cell-based therapies, artificial organs, and engineered living tissues, are dependent on our ability to synthesize or otherwise generate novel materials, fabricate or assemble materials into appropriate 2-D and 3-D forms, and precisely tailor material-related physical and biological properties so as to achieve a desired clinical response. This paper summarizes the scientific and technological opportunities within the fields of biomaterials science and molecular engineering that will likely establish new enabling technologies for cellular and molecular therapies directed at the repair, replacement, or reconstruction of diseased or damaged organs and tissues.

Animals↗