PubMed Health⌕ Search

Biomedical subjects

Joerg Lahann

Publications and source records attributed to Joerg Lahann.

9 recordsLinked to original sources

Switching the electrochemical impedance of low-density self-assembled monolayers.

Because the active remodeling of biointerfaces is a paramount feature of nature, it is very likely that future, advanced biomaterials will be required to mimic at least certain aspects of the dynamic properties of natural interfaces. This need has fueled a quest for model surfaces that can undergo reversible switching upon application of external stimuli. Herein, we report the synthesis and characterization of a model system for studying reversibly switching surfaces based on low-density monolayers of mercaptohexadecanoic acid and mercaptoundecanoic acid. These monolayers were assembled on both gold and silver electrodes. When conducting electrochemical impedance spectroscopy under physiological conditions, these monolayers exhibit significant changes in their electrochemical barrier properties upon application of electrical DC potentials below +400 mV with respect to a standard calomel electrode. We further found the impedance switching to be reversible under physiological conditions. Moreover, the impedance can be fine-tuned by changing the magnitude of the applied electrical potential. Before and during impedance switching at pH 7.4 in aqueous buffer solutions, the low-density monolayers showed good stability according to grazing angle infrared spectroscopy data. We anticipate low-density monolayers to be potentially useful model surfaces when designing active biointerfaces for cell-based studies or rechargeable biosensors.

Biosensing Techniques↗

Triphasic nanocolloids.

Triphasic nanocolloids, that is, nanocolloids with three distinct compartments, were successfully produced by use of electrified co-jetting. Simultaneous manipulation of the three parallel liquid with laminar flows yielded a liquid droplet with three interfaces between the jetting liquids. Under a high electric potential, a single liquid jet was produced from the triple point of the droplet. Separation between the phases was maintained throughout the jetting process and resulted in triphasic nanocolloids. Poly(ethylene oxide), poly(acrylic acid), and poly(acrylamide-co-acrylic acid) solutions were used and verified to be compatible with the process. Fluorescent-labeled biomolecules were selectively incorporated in each phase of the nanocolloids, and confocal laser scanning microscopy was employed for the characterization. Scanning electron microscopy results verified that the sizes of the colloids are in the range of nanocolloids. This simple and versatile technique to fabricate multicompartment nanocolloids is expected to have great impact on drug delivery, molecular imaging, and smart displays.

Journal Article↗

Surface modification of confined microgeometries via vapor-deposited polymer coatings.

The development of generally applicable protocols for the surface modification of complex substrates has emerged as one of the key challenges in biotechnology. The use of vapor-deposited polymer coatings may provide an appealing alternative to the currently employed arsenal of surface modification methods consisting mainly of wet-chemical approaches. Herein, we demonstrate the usefulness of chemical vapor deposition polymerization for surface modification in confined microgeometries with both nonfunctionalized and functionalized poly(p-xylylenes). For a diverse group of polymer coatings, homogeneous surface coverage of different microgeometries featuring aspect ratios as high as 37 has been demonstrated based on optical microscopy and imaging X-ray photoelectron spectroscopy. In addition, height profiles of deposited polymer footprints were obtained by atomic force microscopy and imaging ellipsometry indicating continuous transport and deposition throughout the entire microchannels. Finally, the ability of reactive coatings to support chemical binding of biological ligands, when deposited in previously assembled microchannels, is demonstrated, verifying the usefulness of the CVD coatings for applications in micro/nanofluidics, where surface modifications with stable and designable biointerfaces are essential. The fact that reactive coatings can be deposited within confined microenvironments exhibits an important step toward new device architectures with potential relevance to bioanalytical, medical, or "BioMEMS" applications.

Biotin↗

A surface-modified sperm sorting device with long-term stability.

Microfluidic devices fabricated from poly (dime- thylsiloxane) (PDMS) offer the ability to improve our biological and medical capabilities. Although PDMS offers a range of intriguing benefits for biomedical applications, the intrinsically hydrophobic nature of PDMS may impede with the tremendous potential of these devices. Here, we describe a PDMS-based sperm sorting device, which has been surface-modified via graft-co-polymerization of poly(ethylene glycol) methyl ether methacrylate to create a moderately hydrophilic and non-fouling surface. This process involves the exposure of PDMS to UV/ozone, which activates the PDMS surface to bond to the substrate and, at the same time, initiates the graft-co-polymerization from the PDMS surface. In this study, we confirmed long-term stability of surface-modified PDMS for up to 56 days based on Fourier transformation infrared spectroscopy (FTIR), contact angle measurements, and protein adsorption studies. Moreover, the applicability of our method to PDMS-based sperm sorting devices was demonstrated by successfully sorting human sperm.

Cell Culture Techniques↗

Fabrication of discontinuous surface patterns within microfluidic channels using photodefinable vapor-based polymer coatings.

In this report, we introduce a surface modification method for the fabrication of discontinuous surface patterns within microfluidic systems. The method is based on chemical vapor deposition (CVD) of a photodefinable coating, poly(4-benzoyl-p-xylylene-co-p-xylylene), onto the luminal surface of a microfluidic device followed by a photopatterning step to initiate spatially controlled surface binding. During photopatterning, light-reactive groups of the CVD polymer spontaneously react with molecules adjunct to the surface, such as poly(ethylene oxide). We demonstrate the potential of these reactive polymers for surface modification by preventing nonspecific protein adsorption on different substrates including silicon and poly(dimethylsiloxane) as measured by fluorescence microscopy. More importantly, three-dimensional patterns have successfully been created within polymer-based microfluidic channels, establishing spatially controlled, bioinert surfaces. The herein reported surface modification method addresses a critical challenge with respect to surface engineering of microfluidic devices, namely, the fabrication of discontinuous patterns within microchannels.

Light↗

Biphasic Janus particles with nanoscale anisotropy.

Advances in the field of nanotechnology have fuelled the vision of future devices spawned from tiny functional components that are able to assemble according to a master blueprint. In this concept, the controlled distribution of matter or 'patchiness' is important for creating anisotropic building blocks and introduces an extra design parameter--beyond size and shape. Although the reliable and efficient fabrication of building blocks with controllable material distributions will be of interest for many applications in research and technology, their synthesis has been addressed only in a few specialized cases. Here we show the design and synthesis of polymer-based particles with two distinct phases. The biphasic geometry of these Janus particles is induced by the simultaneous electrohydrodynamic jetting of parallel polymer solutions under the influence of an electrical field. The individual phases can be independently loaded with biomolecules or selectively modified with model ligands, as confirmed by confocal microscopy and transmission electron microscopy. The fact that the spatial distribution of matter can be controlled at such small length scales will provide access to unknown anisotropic materials. This type of nanocolloid may enable the design of multicomponent carriers for drug delivery, molecular imaging or guided self-assembly.

Anisotropy↗

Biologic response to polymer-coated stents: in vitro analysis and results in an iliac artery sheep model.

PURPOSE: To evaluate biologic response to poly(hydroxymethyl-p-xylylene-co-p-xylylene) (PHPX)-coated stents in vitro and in vivo in sheep. MATERIALS AND METHODS: Physical stability, hemocompatibility, and cytotoxicity of the coating were first assessed in vitro. Thirty-six self-expanding nitinol (Memotherm), 24 stainless steel balloon-mounted (Palmaz), and 12 self-expanding nitinol (ZA) stents were coated with PHPX by using chemical vapor deposition polymerization. Seventy-two coated and 72 uncoated stents were placed into iliac arteries of 36 sheep. Sheep were classified into three groups of 12 animals each. In each group, six sheep were killed after 1 month; six, after 6 months. In each sheep, two uncoated stents were placed into one limb; two coated stents of the same type, into the opposite limb. In groups 1 and 2, Palmaz and Memotherm stents were used; in group 3, Memotherm and ZA stents were used. In groups 1 and 3, arteries were healthy. In group 2, arteries were pretreated with a Fogarty maneuver. Stent patency was measured with intravascular ultrasonography (US) and histologic analysis. Cellular response to coated and uncoated stents was assessed. Measurements were compared (Wilcoxon test). RESULTS: In vitro, PHPX coating was stable; hemocompatibility and cytotoxicity were similar to those of stainless steel. In vivo, patency of coated and uncoated Palmaz and ZA stents was not different (P >.05). Patency of coated and uncoated Memotherm stents did not differ in four of six follow-up subgroups, but it was significantly reduced in group 2 after 6 months (intravascular US, P =.03; histologic analysis, P =.01) and in group 3 after 1 month (histologic analysis, P =.01). Histologically, the cellular response to coated and uncoated stents was not different (P >.05). CONCLUSION: PHPX coating had good physical stability and biocompatibility in vitro and in vivo. Performance of coated and uncoated Palmaz and ZA stents was similar. Patency of Memotherm stents was similar in four of six follow-up subgroups. Materials effects did not result in severely enhanced neointimal hyperplasia.

Animals↗

A reversibly switching surface.

We report the design of surfaces that exhibit dynamic changes in interfacial properties, such as wettability, in response to an electrical potential. The change in wetting behavior was caused by surface-confined, single-layered molecules undergoing conformational transitions between a hydrophilic and a moderately hydrophobic state. Reversible conformational transitions were confirmed at a molecular level with the use of sum-frequency generation spectroscopy and at a macroscopic level with the use of contact angle measurements. This type of surface design enables amplification of molecular-level conformational transitions to macroscopic changes in surface properties without altering the chemical identity of the surface. Such reversibly switching surfaces may open previously unknown opportunities in interfacial engineering.

Adsorption↗