Biomedical subjects

Jonnalagadda Raghava Rao

Publications and source records attributed to Jonnalagadda Raghava Rao.

13 recordsLinked to original sources

PubMed2006

Removal of basic yellow dye from aqueous solution by sorption on green alga Caulerpa scalpelliformis.

Dynamic batch experiments were carried out for the biosorption of basic yellow dye on to the green macroalgae Caulerpa scalpelliformis. The factors affecting the sorption process such as the initial concentration of the dye and pH of the solution, the adsorbent dosage and the time of contact were studied. The sorption kinetics followed pseudo-second order kinetic model. The Caulerpa species exhibited a maximum uptake of 27 mg of dye per gram of seaweed. The Boyd's plot confirmed the external mass transfer as the rate-limiting step. The average effective diffusion coefficient was found to be 2.47 x 10(-4)cm(2)/s. Sorption equilibrium studies demonstrated that the biosorption followed Freundlich isotherm model, which implies a heterogeneous sorption phenomenon. Various thermodynamic parameters such as enthalpy of sorption DeltaH degrees , free energy change DeltaG degrees and entropy DeltaS degrees were estimated. The negative value of DeltaH degrees and negative values of DeltaG degrees show the sorption process is exothermic and spontaneous. The negative value of entropy DeltaS degrees shows the decreased randomness at the solid-liquid interface during the sorption of dyes onto green seaweed.

Adsorption↗

PubMed2006

Stabilization of type I collagen against collagenases (type I) and thermal degradation using iron complex.

The widespread application of collagen as a biomaterial warrants research in understanding the stabilization of the same. In this study, interaction of iron-tetrakis (hydroxymethyl) phosphonium (THP) complex with type I collagen has been investigated. DSC and hydrothermal measurement studies reveal that the shrinkage temperature of iron-THP treated rat tail tendon (RTT) collagen is 33 degrees C higher than that of native RTT collagen. Fe-THP complex also brings about high degree of enzymatic stability to type I collagen. The effect of Fe-THP on the conformation of collagen was studied using circular dichroism and it was found that no major alterations in the triple helical structure of collagen occur on treatment with Fe-THP. It is observed from viscosity experiment results that though Fe-THP complex is able to bring about long range ordering of collagen, as evident from the thermal and enzymatic stability imparted to collagen, this ordering does not lead to any aggregation of collagen. Since THPS is reducing in nature, it is expected to keep iron in the +2 state and if THP chelates to Fe(II), the hydrolytic behavior of iron can also be controlled.

Animals↗

PubMed2006

Wet oxidation of acid brown dye by hydrogen peroxide using heterogeneous catalyst Mn-salen-Y zeolite: a potential catalyst.

Catalytic wet hydrogen peroxide oxidation of acid dye has been explored in this study. Manganese(III) complex of N,N'-ethylene bis(salicylidene-aminato) (salenH(2)) has been encapsulated in super cages of zeolite-Y by flexible ligand method. The catalyst has been characterized by FT-IR, XRD, TG/DTA and nitrogen adsorption studies. The effects of various parameters such as pH, catalyst and hydrogen peroxide concentration on the oxidation of dye were studied. The results indicate that after 20 min at 30 degrees C, 0.175 M H(2)O(2) and 3g/L catalyst, about 90% dye removal was obtained. These studies indicate that manganese-salen complex immobilized on zeolite framework can act as a good heterogeneous catalyst for removal of dye from wastewaters.

Catalysis↗

PubMed2006

Reversing the conventional leather processing sequence for cleaner leather production.

Conventional leather processing generally involves a combination of single and multistep processes that employs as well as expels various biological, inorganic, and organic materials. It involves nearly 14-15 steps and discharges a huge amount of pollutants. This is primarily due to the fact that conventional leather processing employs a "do-undo" process logic. In this study, the conventional leather processing steps have been reversed to overcome the problems associated with the conventional method. The charges of the skin matrix and of the chemicals and pH profiles of the process have been judiciously used for reversing the process steps. This reversed process eventually avoids several acidification and basification/neutralization steps used in conventional leather processing. The developed process has been validated through various analyses such as chromium content, shrinkage temperature, softness measurements, scanning electron microscopy, and physical testing of the leathers. Further, the performance of the leathers is shown to be on par with conventionally processed leathers through bulk property evaluation. The process enjoys a significant reduction in COD and TS by 53 and 79%, respectively. Water consumption and discharge is reduced by 65 and 64%, respectively. Also, the process benefits from significant reduction in chemicals, time, power, and cost compared to the conventional process.

Animals↗

PubMed2005

Silicate enhanced enzymatic dehairing: a new lime-sulfide-free process for cowhides.

A conventional dehairing process with sodium sulfide and lime is a major source of the pollution from the tanning industry. In other words, conventional dehairing processes degrade the hair to the extent that it cannot be recovered; thus, these processes become a major contributor to wastewater pollution. In this study, an attempt has been made to develop a lime and sulfide-free dehairing process using a commercial enzyme formulation with the activation of a silicate salt. A dip and pile method of application has been standardized. The amount of enzyme and sodium metasilicate has also been optimized based on complete removal of hair. Enhancement of enzyme activity by the addition of silicate has been demonstrated through activity measurements. Hair removal is found to be complete using scanning electron microscope analysis. Strength and bulk properties of the experimental leathers are comparable to that of control leathers. The process enjoys a significant reduction in chemical oxygen demand (COD) and total solids (TS) by 53 and 26%, respectively. More importantly, the application of enzyme for dehairing results in an 8% area increase in the final leather. Also, the process is proven to be techno-economically feasible.

Animals↗

PubMed2005

Solid waste removes toxic liquid waste: adsorption of chromium(VI) by iron complexed protein waste.

The leather processing industry generates huge amounts of wastes, both in solid and liquid form. Fleshing from animal hides/skins is one such waste that is high in protein content. In this study, raw fleshing has been complexed with iron and is used for removal of chromium(VI). The effect of pH and the initial concentration of chromium(VI) on the removal of Cr(IV) by iron treated fleshing is presented. Iron treatment is shown to greatly improve adsorption of the fleshing for hexavalent chromium. The ultimate adsorption capacity of iron treated fleshing is 51 mg of chromium(VI) per gram of fleshing. That of untreated fleshing is 9 mg/g such that iron treatment increases the adsorption capacity of fleshing by 10-fold. The measured adsorption kinetics is well described by a pseudo-second-order kinetic model. The uptake of chromium(VI) by fleshing is best described by the Langmuir adsorption isotherm model. X-ray photoelectron spectroscopic (XPS) studies show that the iron is incorporated into the protein matrix. Shifts in XPS spectra suggest that dichromate binding occurs with iron at active adsorption sites and that iron treated fleshing removes chromium(VI) without reducing it to chromium(III).

Adsorption↗

PubMed2004

Natural leathers from natural materials: progressing toward a new arena in leather processing.

Globally, the leather industry is currently undergoing radical transformation due to pollution and discharge legislations. Thus, the leather industry is pressurized to look for cleaner options for processing the raw hides and skins. Conventional methods of pre-tanning, tanning and post-tanning processes are known to contribute more than 98% of the total pollution load from the leather processing. The conventional method of the tanning process involves the "do-undo" principle. Furthermore, the conventional methods employed in leather processing subject the skin/ hide to a wide variation in pH (2.8-13.0). This results in the emission of huge amounts of pollution loads such as BOD, COD, TDS, TS, sulfates, chlorides and chromium. In the approach illustrated here, the hair and flesh removal as well as fiber opening have been achieved using biocatalysts at pH 8.0, pickle-free natural tanning employing vegetable tannins, and post-tanning using environmentally friendly chemicals. Hence, this process involves dehairing, fiber opening, and pickle-free natural tanning followed by ecofriendly post-tanning. It has been found that the extent of hair removal and opening up of fiber bundles is comparable to that of conventionally processed leathers. This has been substantiated through scanning electron microscopic analysis and softness measurements. Performance of the leathers is shown to be on par with conventionally chrome-tanned leathers through physical and hand evaluation. The process also exhibits zero metal (chromium) discharge and significant reduction in BOD, COD, TDS, and TS loads by 83, 69, 96, and 96%, respectively. Furthermore, the developed process seems to be economically viable.

Animals↗

PubMed2004

Bioaccumulation of chromium from tannery wastewater: an approach for chrome recovery and reuse.

The presence of chromium in the effluent is a major concern for the tanning industry. Currently, chemical precipitation methods are practiced for the removal of chromium from the effluent, but that leads to the formation of chrome-bearing solid wastes. The other membrane separation and ion exchange methods available are unfeasible due to their cost. In this study, the removal of chromium from tannery effluent has been carried out using abundantly available brown seaweed Sargassum wightii. Simulated chrome tanning solution was used for the standardization of experimental trials. Various factors influencing the uptake of chromium, viz., quantity of seaweed, concentrations of chromium, pH of the chrome-bearing wastewater, and duration of treatment, have been studied. Chemical modification of the seaweed through pretreatment with sulfuric acid, magnesium chloride, and calcium chloride showed improved uptake of chromium. Langmuir and Freundlich isotherms have been fitted for various quantities of seaweed. The dynamic method of treatment of protonated seaweed with simulated chrome tanning solution at a pH of 3.5-3.8 for a duration of 6 h gave the maximum uptake of about 83%. A similar uptake has been established for commercial chrome tanning wastewater containing the same concentration of chromium. The Sargassum species exhibited a maximum uptake of 35 mg of chromium per gram of seaweed. Fourier transform infrared spectroscopy, energy-dispersive X-ray analysis, and flame photometry studies have been carried out to understand the mechanistic pathway for the removal of chromium. The potential reuse of chromium-containing seaweed for the preparation of basic chromium sulfate (tanning agent) has been demonstrated.

Animals↗

PubMed2004

Interaction of aldehydes with collagen: effect on thermal, enzymatic and conformational stability.

Stabilization of type I rat tail tendon (RTT) collagen by various aldehydes, viz. formaldehyde, gluteraldehyde, glyoxal and crotanaldehyde was studied to understand the effect of each on the thermal, enzymatic and conformational stability of collagen. The aldehydes have been found to increase the heat stability of rat tail tendon collagen fibres from 62 to 77-86 degrees C. The increase in thermal stability was found to be in a species dependent manner. The variation in the thermal stability of collagen brought about by aldehydes was in the order of formaldehyde > gluteraldehyde > glyoxal > crotanaldehdye. The aldehydes also impart a high degree of stability to collagen against the activity of the degrading enzyme, collagenase. The order of enzymatic stability brought about by aldehydes follows the same trend as the thermal stability brought about by them. This shows that the number of cross-links formed influence both the thermal and enzymatic stability in the similar manner. The effect of various aldehydes on the secondary structure of collagen was studied using circular dichroism and it was found that the aldehydes lead to changes in the amplitude of the circular dichroic (CD) spectrum but did not alter the triple helical conformation of collagen. The secondary structure of collagen is not significantly altered on interaction with different aldehydes.

Aldehydes↗

PubMed2003

Biointervention makes leather processing greener: an integrated cleansing and tanning system.

The do-undo methods adopted in conventional leather processing generate huge amounts of pollutants. In other words, conventional methods employed in leather processing subject the skin/hide to wide variations in pH. Pretanning and tanning processes alone contribute more than 90% of the total pollution from leather processing. Included in this is a great deal of solid wastes such as lime and chrome sludge. In the approach described here, the hair and flesh removal as well as fiber opening have been achieved using biocatalysts at pH 8.0 for cow hides. This was followed by a pickle-free chrome tanning, which does not require a basification step. Hence, this tanning technique involves primarily three steps, namely, dehairing, fiber opening, and tanning. It has been found that the extent of hair removal, opening up of fiber bundles, and penetration and distribution of chromium are comparable to that produced by traditional methods. This has been substantiated through scanning electron microscopic, stratigraphic chrome distribution analysis, and softness measurements. Performance of the leathers is shown to be on par with conventionally processed leathers through physical and hand evaluation. Importantly, softness of the leathers is numerically proven to be comparable with that of control. The process also demonstrates reduction in chemical oxygen demand load by 80%, total solids load by 85%, and chromium load by 80% as compared to the conventional process, thereby leading toward zero discharge. The input-output audit shows that the biocatalytic three-step tanning process employs a very low amount of chemicals, thereby reducing the discharge by 90% as compared to the conventional multistep processing. Furthermore, it is also demonstrated that the process is technoeconomically viable.

Animals↗

PubMed2003

Effect of zirconium(IV) complexes on the thermal and enzymatic stability of type I collagen.

Understanding the mechanism of stabilization of collagen is an important area of research. Metal ions are known to interact with collagen and bring about the stability of the same. In the present investigation, the interaction of zirconium(IV) complexes with collagen was studied. The effect of zirconium(IV) complexes, namely zirconium oxychloride and zirconium oxalate on the enzymatic and thermal stability of collagen was investigated. Zirconium has been found to increase the hydrothermal stability of the rat tail tendon (RTT) collagen fibers to about 8-10 degrees C more than that of the native collagen. The order of stabilization of zirconium(IV) complexes is zirconium oxychloride>zirconium oxalate. This could be due to the differences in the type of interaction with collagen, which is also reflected in the differences in the conformational changes of collagen brought about by the two complexes. Zirconium oxychloride, which forms tetrameric species in solution, has been shown to have better crosslinking with collagen as seen from viscometry studies and hence provides better enzymatic stability to collagen than zirconium oxalate, which largely forms monomeric species in solution.

Animals↗

PubMed2002

Zero discharge tanning: a shift from chemical to biocatalytic leather processing.

Beam house processes (Beam house processes generally mean liming-reliming processes, which employ beam.) contribute more than 60% of the total pollution from leather processing. The use of lime and sodium sulfide is of environmental concern (1, 2). Recently, the authors have developed an enzyme-based dehairing assisted with a very low amount of sodium sulfide, which completely avoids the use of lime. However, the dehaired pelt requires opening up of fiber bundles for further processing, where lime is employed to achieve this through osmotic swelling. Huge amounts of lime sludge and total solids are the main drawbacks of lime. An alternative bioprocess, based on alpha-amylase for fiber opening, has been attempted after enzymatic unhairing. This totally eliminates the use of lime in leather processing. This method enables subsequent processes and operations in leather making feasible without a deliming process. A control experiment was run in parallel using conventional liming-reliming processes. It has been found that the extent of opening up of fiber bundles using alpha-amylase is comparable to that of the control. This has been substantiated through scanning electron microscopic, stratigraphic chrome distribution analysis, and softness measurements. Performance of the leathers is shown to be on a par with leathers produced by the conventional process through physical and hand evaluation. Importantly, softness of the leathers is numerically proven to be comparable with that of control. The process also demonstrates reduction in chemical oxygen demand load by 45% and total solids load by 20% compared to the conventional process. The total dry sludge from the beam house processes is brought down from 152 to 8 kg for processing 1 ton of raw hides.

Animals↗

PubMed2002

Green route for the utilization of chrome shavings (chromium-containing solid waste) in tanning industry.

Chromium-containing wastes from various industrial sectors are under critical review. Leather processing is one such industrial activity that generates chromium-bearing wastes in different forms. One of them is chrome shavings, and this contributes to an extent of 10% of the quantum of raw skins/hides processed, amounting to 0.8 million ton globally. In this study, the high protein content of chrome shavings has been utilized for reduction of chromium(VI) in the preparation of chrome tanning agent. This approach has been exploited for the development of two products: one with chrome shavings alone as reducing agent and the other with equal proportion of chrome shavings and molasses. The developed products exhibit more masking due to the formation of intermediate organic oligopeptides. This has been corroborated through the spectral, hydrolysis, and species-wise distribution studies. The formation of these organic masking agents helps in chrome tanning by shifting the precipitation point of chromium to relatively higher pH levels. Hence, the developed products find use as chrome tanning agents for leather processing, thus providing a means for better utilization of chrome shaving wastes.

Carcinogens, Environmental↗