Biomedical subjects

Jordi Esquena

Publications and source records attributed to Jordi Esquena.

5 recordsLinked to original sources

PubMed2006

Phase behavior and preparation of mesoporous silica in aqueous mixtures of fluorinated surfactant and hydrophobic fluorinated polymer.

The phase behavior and formation of self-assemblies in the ternary water/fluorinated surfactant (C(8)F(17)EO(10))/hydrophobic fluorinated polymer (C(3)F(6)O)(n)COOH system and the application of those assemblies in the preparation of mesostructured silica have been investigated by means of phase study, small angle X-ray scattering, and rheology. Hexagonal (H(1)), bicontinuous cubic (V(1)) with Ia3d symmetry, and polymer rich lamellar (L(alpha)(')) are observed in the ternary diagram. C(8)F(17)EO(10) molecules are dissolved in polymer rich aggregates, whereas (C(3)F(6)O)(n)COOH molecules are practically insoluble in the surfactant lamellar phase due to packing restrictions. Hence, two types of lamellar phases exist: one with surfactant rich (L(alpha)) and the other with polymer rich (L(alpha)(')) in the water/C(8)F(17)EO(10)/(C(3)F(6)O)(n)COOH system. As suggested by rheological measurements, worm-like micelles are present in C(8)F(17)EO(10) aqueous solutions but a rod-sphere transition takes place by solubilization of (C(3)F(6)O)(n)COOH. C(8)F(17)EO(10) acts as a structure directing agent for the preparation of hexagonal mesoporous silica by the precipitation method. The addition of (C(3)F(6)O)(n)COOH induces the formation of larger but disordered pores.

Journal Article↗

PubMed2005

Emulsion polymerization of styrene and methyl methacrylate using a hydrophobically modified inulin and comparison with other surfactants.

The use of a new class of graft polymer surfactants, based on inulin, in emulsion polymerization of poly(methyl methacrylate) (PMMA) and polystyrene (PS) particles is described. PS and PMMA were synthesized by emulsion polymerization, and stable particles with a high monomer content (50 wt %) were obtained with a very small amount of polymeric surfactant ([surfactant]/[monomer] = 0.0033). The latex dispersions were characterized by dynamic light scattering and by transmission electron microscopy to obtain the average particle size and the polydispersity index, and the stability was determined by turbidimetry measurements and expressed in terms of critical coagulation concentration. The last section gives a comparison of PMMA particles prepared by emulsion polymerization using classical surfactants from different types as emulsifiers with that obtained using the copolymer surfactant. It shows the superiority of INUTEC SP1 as it is the only one that allows stable particles at 20 wt % monomer content, with a smaller ratio [surfactant]/[monomer] = 0.002.

Journal Article↗

PubMed2005

The influence of surfactant mixing ratio on nano-emulsion formation by the pit method.

The formation of O/W nano-emulsions by the PIT emulsification method in water/mixed nonionic surfactant/oil systems has been studied. The hydrophilic-lipophilic properties of the surfactant were varied by mixing polyoxyethylene 4-lauryl ether (C12E4) and polyoxyethylene 6-lauryl ether (C12E6). Emulsification was performed in samples with constant oil concentration (20 wt%) by fast cooling from the corresponding HLB temperature to 25 degrees C. Nano-emulsions with droplet radius 60-70 nm and 25-30 nm were obtained at total surfactant concentrations of 4 and 8 wt%, respectively. Moreover, droplet size remained practically unchanged, independent of the surfactant mixing ratio, X(C12E6). At 4 wt% surfactant concentration, the polydispersity and instability of nano-emulsions increased with the increase in X(C12E6). However, at 8 wt% surfactant concentration, nano-emulsions with low polydispersity and high stability were obtained in a wide range of surfactant mixing ratios. Phase behavior studies showed that at 4 wt% surfactant concentration, three-liquid phases (W+D+O) coexist at the starting emulsification temperature. Furthermore, the excess oil phase with respect to the microemulsion D-phase increases with the increase in X(C12E6), which could explain the increase in instability. At 8 wt% surfactant concentration, a microemulsion D-phase is present when emulsification starts. The low droplet size and polydispersity and higher stability of these nano-emulsions have been attributed, in addition to the increase in the surface or interfacial activity, to the spontaneous emulsification produced in the microemulsion D-phase.

Journal Article↗

PubMed2004

Phase behavior and nano-emulsion formation by the phase inversion temperature method.

Formation of oil-in-water nano-emulsions has been studied in the water/C12E4/isohexadecane system by the phase inversion temperature emulsification method. Emulsification started at the corresponding hydrophilic-lipophilic balance temperature, and then the samples were quickly cooled to 25 degrees C. The influence of phase behavior on nano-emulsion droplet size and stability has been studied. Droplet size was determined by dynamic light scattering, and nano-emulsion stability was assessed, measuring the variation of droplet size as a function of time. The results obtained showed that the smallest droplet sizes were produced in samples where the emulsification started in a bicontinuous microemulsion (D) phase region or in a two-phase region consisting of a microemulsion (D) and a liquid crystalline phase (L(alpha)). Although the breakdown process of nano-emulsions could be attributed to the oil transference from the smaller to the bigger droplets, the increase in instability found with the increase in surfactant concentration may be related to the higher surfactant excess, favoring the oil micellar transport between the emulsion droplets.

Journal Article↗

PubMed2000

Nitrogen Sorption Studies of Silica Particles Obtained in Emulsion and Microemulsion Media.

The internal surface structures of silica aerogel particles synthesized using different catalysts in emulsion and microemulsion media have been investigated by means of N(2) adsorption and desorption isotherms. Surface fractal dimensions have been computed using different methods: Frankel-Halsey-Hill plots of the adsorption isotherms, the thermodynamic fractal isotherm equation, and a modification of the thermodynamic fractal isotherm equation. Silica aerogels synthesized in emulsion media with an acidic catalyst have a high specific surface area without micropores and show two separate ranges of scales where the surface fractal dimensions are different and constant. Silica aerogels synthesized in emulsion media with a basic catalyst have a moderate specific surface area with a high percentage of micropores and show constant surface fractal dimensions over a larger range. Silica aerogels synthesized in microemulsion media with a basic catalyst have a low specific surface area with a moderate percentage of micropores and show a moderate range of scales over which the surface fractal dimension is constant. Analyses by both the thermodynamic and modified thermodynamic methods give similar ranges of the surface fractal dimensions of the silica particles. Copyright 2000 Academic Press.

Journal Article↗