Biomedical subjects

Jouko Peltonen

Publications and source records attributed to Jouko Peltonen.

4 recordsLinked to original sources

PubMed2006

Topography and surface energy dependent calcium phosphate formation on Sol-Gel derived TiO2 coatings.

Heterogeneous nucleation and growth of calcium phosphate (CaP) on sol-gel derived TiO(2) coatings was investigated in terms of surface topography and surface energy. The topography of the coatings was derived from AFM measurements, while the surface energy was determined with contact angle measurements. The degree of precipitation was examined with scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The precipitation of CaP was found to be dependent on both topography and surface energy. A high roughness value when combining the RMS roughness parameter S(q) with the number of local maxima per unit area parameter S(ds) enhances CaP formation. The hydrophilicity of the coating was also found to be of importance for CaP formation. We suggest that the water contact angle, which is a direct measure of the hydrophilicity of the surface, may be used to evaluate the surface energy dependent precipitation kinetics rather than using the often applied Lewis base parameter.

Journal Article↗

PubMed2006

Optical properties of thermally responsive amphiphilic gold nanoparticles protected with polymers.

Amphiphilic thermally responsive gold nanoparticles have been prepared by protecting the particles with both polystyrene, PS, and poly(N-isopropylacrylamide), PNIPAM, chains. Particles form a monolayer on a water surface in a Langmuir trough, and according to in situ spectroscopic measurements, the surface plasmon resonance, SPR, band undergoes a blue-shift during the monolayer compression. The compression-induced blue-shift is related to a change in the conformation of tethered PNIPAM chains; the phenomenon is discussed on the basis of Mie-Drude theory. In contrast, a red-shift in the SPR of the multilayers of the same nanoparticles transferred at different temperatures has been observed with increasing the deposition cycle, attributed to the presence of a weak interparticle coupling in the multilayer.

Journal Article↗

PubMed2006

Rapid electrochemiluminoimmunoassay of human C-reactive protein at planar disposable oxide-coated silicon electrodes.

Electrochemiluminescence (ECL) of aromatic Tb(III) chelates at thin insulating film-coated electrodes provides a means for extremely sensitive detection of Tb(III) chelates and also of biologically interesting compounds if these chelates are used as labels in bioaffinity assays. The suitability of silicon electrodes coated with thermally grown silicon dioxide film as disposable working electrodes in sensitive time-resolved ECL measurements is demonstrated, and a rapid electrochemiluminoimmunoassay (ECLIA) of human C-reactive protein (hCRP) is described. Tb(III) chelate labels can be detected almost down to picomolar level, and the calibration curve of these labels covers more than 6 orders of magnitude of chelate concentration. The calibration curve of the present immunometric hCRP assay was found to be linear over a wide range, approximately 4 orders of magnitude of hCRP concentration, the detection limit of the protein being 0.3 ng mL(-1) (mean background + 2SD) on CV values of about 10-30%, depending on the immunoassay incubation time. In the ECLIA measurements, different incubation times were tested from 15 min (giving above-mentioned performance) to as short as only 2 min, which still gave successful results with approximately 20,000 times better detection limit levels than traditional commercial assay methods. During the ECLIA process, also the Si electrode surface morphology was also investigated by atomic force microscope monitoring.

Biosensing Techniques↗

PubMed2004

Topographical parameters for specifying a three-dimensional surface.

The importance of different surface geometries and thereby the need for versatile surface identification by describing a number of different surface features is emphasized. A set of topographical parameters for the description of the amplitude and spatial and hybrid properties of surfaces was utilized for a versatile three-dimensional surface characterization of sol-gel samples with different topographies. The image data were measured by atomic force microscopy. The results demonstrate the power of the roughness parameters to identify surfaces according to their specific characteristics. An example is also given about how certain surface topographical properties may control the material reactivity.

Letter↗