Biomedical subjects

Jukka Rantanen

Publications and source records attributed to Jukka Rantanen.

5 recordsLinked to original sources

PubMed2003

Tablet surface characterisation by various imaging techniques.

The aim of this study was to characterise tablet surfaces using different imaging and roughness analytical techniques including optical microscopy, scanning electron microscopy (SEM), laser profilometry and atomic force microscopy (AFM). The test materials compressed were potassium chloride (KCl) and sodium chloride (NaCl). It was found that all methods used suggested that the KCl tablets were smoother than the NaCl tablets and higher compression pressure made the tablets smoother. Imaging methods like optical microscopy and SEM can give useful information about the roughness of the sample surface, but they do not provide quantitative information about surface roughness. Laser profilometry and AFM on the other hand provide quantitative roughness data from two different scales, laser profilometer from 1 mm and atomic force microscope from 90 microm scale. AFM is a powerful technique but other imaging and roughness measuring methods like SEM, optical microscopy and laser profilometry give valuable additional information.

Compressive Strength↗

PubMed2003

Effects of excipients on hydrate formation in wet masses containing theophylline.

Transformations between solid phases in dosage forms can lead to instability in drug release. Thus, it is important to understand mechanisms and kinetics of phase transformations and factors that may influence them. During wet granulation theophylline shows pseudopolymorphic changes that may alter its dissolution rate. The aim of this study was to investigate whether excipients, such as alpha-lactose monohydrate or the highly water absorbing silicified microcrystalline cellulose (SMCC) can influence the hydrate formation of theophylline. In particular, the aim was to study if SMCC offers protection against the formation of theophylline monohydrate relative to alpha-lactose monohydrate in wet masses after an overnight equilibration and the stability of final granules during controlled storage. In addition, the aim was to study the use of spectroscopic methods to identify hydrate formation in the formulations containing excipients. Off-line evaluation of materials was performed using X-ray powder diffractometry, near infrared and Raman spectroscopy. alpha-Lactose monohydrate with minimal water absorbing potential was not able to prevent but enhanced hydrate formation of theophylline. Even though SMCC is able to take large amounts of water into its internal structure, it was able to inhibit the formation of theophylline monohydrate only at low moisture contents, not at the amounts of water needed to form granules. Both the spectroscopic methods used could identify the hydrate formation even though there were excipients in the formulation.

Absorption↗

PubMed2003

Physical stability of a microcrystalline beta-sitosterol suspension in oil.

Sterols have been shown to reduce plasma cholesterol by blocking the absorption of cholesterol from the gut. The physical properties of crystalline plant sterols limit their use in foods. A coarse-grained structure can be avoided by recrystallisation, a method that affords a reduction in the particle size. A previous work described how to produce a microcrystalline beta-sitosterol suspension. The present study deals with the stability of that suspension. Recrystallisation was carried out by two different methods; one based on rapid the other based on slow cooling, whereby six different compositions were made containing 5-30% of beta-sitosterol and secondly either 5 or 20% water was added. The particle size and habit were evaluated during a 16 weeks storage period (+4 or -19 degrees C) by way of optical microscopy. The crystal structure and degree of crystallinity was analysed by X-ray diffraction. Suspensions can, in most cases, be stored for 16 weeks without any changes to the size and habit. The only evidence of crystal growth came from a suspension with a low sterol concentration at a temperature of +4 degrees C. This is due to the dissolution-diffusion process which is affected by temperature and viscosity. Suspensions containing higher amounts of sterol remained stable, if stored at +4 or -19 degrees C, for 16 weeks. The suspensions included both hemihydrous and monohydrous beta-sitosterol crystals. Suspensions containing less sterol showed greater amounts of monohydrated crystals. This illustrates more water penetration into the crystals. A higher sterol concentration led to a larger number of smaller crystals creating reflections similar to hemihydrated crystals.

Cholesterol↗

PubMed2002

Hydrate formation during wet granulation studied by spectroscopic methods and multivariate analysis.

PURPOSE: The aim was to follow hydrate formation of two structurally related drugs, theophylline and caffeine, during wet granulation using fast and nondestructive spectroscopic methods. METHODS: Anhydrous theophylline and caffeine were granulated with purified water. Charge-coupled device (CCD) Raman spectroscopy was compared with near-infrared spectroscopy (NIR) in following hydrate formation of drugs during wet granulation (off-line). To perform an at-line process analysis, the effect of water addition was monitored by NIR spectroscopy and principal components analysis (PCA). The changes in the crystal arrangements were verified by using X-ray powder diffraction (XRPD). RESULTS: Hydrate formation of theophylline and caffeine could be followed by CCD Raman spectroscopy. The NIR and Raman spectroscopic results were consistent with each other. NIR revealed the state of water, and Raman spectroscopy gave information related to the drug molecule itself. The XRPD confirmed the spectroscopic results. PCA with three principal components explained 99.9 of the spectral variation in the second derivative NIR spectra. CONCLUSIONS: Both CCD Raman and NIR spectroscopic methods can be applied to monitoring of hydrate formation processes. However, NIR is more suitable for monitoring solid-water interactions.

Multivariate Analysis↗

PubMed2002

Development of an automation system for a tablet coater.

An instrumentation and automation system for a side-vented pan coater with a novel air-flow rate measurement system for monitoring the film-coating process of tablets was designed and tested. The instrumented coating system was tested and validated by film-coating over 20 pilot-scale batches of tablets with aqueous-based hydroxypropyl methylcellulose (HPMC). Thirteen different process parameters were continuously measured and monitored, and the most significant ones were logged for analysis. Laser profilometry was used to measure the surface roughness of the coated tablets. The instrumentation system provided comprehensive and quantitative information on the process parameters monitored. The measured process parameters and the responses of the film-coated tablet batches showed that the coating process is reproducible. The inlet air-flow rate influenced the coating process and the subsequent quality of the coated tablets. Increasing the inlet flow rate accelerated the drying of the tablet surface. At high inlet flow rate, obvious film-coating defects (ie, unacceptable surface roughness of the coated tablets) were observed and the loss of coating material increased. The instrumented and automated pan-coating system described, including historical data storage capability and a novel air-flow measurement system, is a useful tool for controlling and characterizing the tablet film-coating process. Monitoring of critical process parameters increases the overall coating process efficiency and predictability.

Automation↗