Biomedical subjects

Julio San Román

Publications and source records attributed to Julio San Román.

At least 19 recordsLinked to original sources

PubMed2007

Development of wollastonite-poly(ethylmethacrylate co-vinylpyrrolidone) based materials for multifunctional devices.

The manufacturing of a composite made of a synthetic bioactive ceramic, pseudowollastonite (psW), and a bioresorbable copolymer ethylmethacrylate-vinylpyrrolidone (EMA/VP) is presented in this article. psW porous blocks were produced by dipping an open porous polyurethane foam in a psW containing slurry. A 40/60 wt % EMA/VP monomers mixture was poured on the blocks, and free radical polymerization initiated by azobis(isobutyronitrile) at 50 degrees C. Disks of 1 mm height were obtained by cutting the composite with a diamond saw, and bioresorption and bioactivity of the specimens were tested by immersion of the disks into SBF. A ceramic/polymer weight ratio of 72/28, greater than the usually achievable ratio by polymeric solidification of slurries of monomers charged with a powdered solid component, has been obtained. The system is bioactive and does not change the pH of the medium during the degradation test.

Biocompatible Materials↗

PubMed2007

Influence of the activator in an acrylic bone cement on an array of cement properties.

In all but one of the acrylic bone cement brands used in cemented arthroplasties, N,N-dimethyl-4-toluidine (DMPT) serves as the activator of the polymerization reaction. However, many concerns have been raised about this activator, all related to its toxicity. Thus, various workers have assessed a number of alternative activators, with two examples being N,N-dimethylamino-4-benzyl laurate (DMAL) and N,N-dimethylamino-4-benzyl oleate (DMAO). The results of limited characterization of cements that contain DMAL or DMAO have been reported in the literature. The present work is a comprehensive comparison of cements that contain one of these three activators, in which the values of a large array of their properties were determined. These properties range from the setting time and maximum exotherm temperature of the curing cement to the variation of the loss elastic modulus of the cured cement with frequency of the applied indenting force in dynamic nanoindentation tests. The present results, taken in conjunction with those presented in previous reports by the present authors and co-workers on other properties of these cements, indicate that both DMAL and DMPT are suitable alternatives to DMPT.

Acrylic Resins↗

PubMed2006

Bioresorbable poly(ester-ether urethane)s from L-lysine diisocyanate and triblock copolymers with different hydrophilic character.

Bioresorbable linear poly(ester-ether urethane)s with different hydrophilic character were synthesized from block copolymers of poly(epsilon-caprolactone)-poly(ethylene oxide)-poly(epsilon-caprolactone) (PCL-PEO-PCL) as macrodiols, and L-lysine diisocyanate (LDI). A series of PCL-PEO-PCL triblock copolymers with different PEO and PCL chain length was obtained by reacting PEO with epsilon-caprolactone. Polyurethanes were synthesized by reacting the triblock copolymers with LDI in solution using stannous 2-ethylhexanoate as catalyst. The prepared triblock copolymers and polyurethanes were fully characterized by proton nuclear magnetic resonance spectroscopy, size exclusion chromatography, differential scanning calorimetry, and wide-angle X-ray diffraction. Water uptake, hydrolytic stability, and tensile properties of polyurethanes with different composition were evaluated and discussed in terms of the chain length and molecular weight of the polymers and its block components. Water uptake seems to depend on the ethylene oxide unit content of the polyurethane regardless of the triblock structure. Mechanical properties of the synthesized polymers were strongly affected by the molecular weight achieved during polymerization. The use of triblock macrodiols with different hydrophilicity allowed the preparation of a series of polyurethanes having a broad range of properties.

Biocompatible Materials↗

PubMed2006

Capillary electrophoresis-mass spectrometry of a new cross-linker with acrylic functionality.

Analytical characterization of dimethacrylate-tyrosine-lysine-tyrosine (DMTLT, a new biodegradable acrylic cross-linker synthesized at our laboratory) is carried out using CE-MS. DMTLT is a pseudopeptide composed by tyrosine-lysine-tyrosine amino acids linked through urea bonds with two methacrylic groups, one at each end of the molecule, making this compound an excellent cross-linker for polymerization reactions and for obtaining new biodegradable materials. A new CE-MS method is developed for the characterization of DMTLT and its products of degradation after basic hydrolysis. In order to carry out an exhaustive examination of such degradation products methods based on CE coupled to IT and TOF-MS are employed. Based on CE-IT-MS results and the elemental composition of the degradation products obtained by CE-TOF-MS, conclusions on the mechanism and kinetic of hydrolysis of DMTLT are obtained confirming both the usefulness of CE-MS to characterize new biomaterials and the applicability of DMTLT for preparing new biodegradable polymers. These results are corroborated through the CE-MS detection of the identified products of degradation in a dimethyl acrylamide polymer cross-linked with DMTLT.

Cross-Linking Reagents↗

PubMed2006

Capillary electrophoresis using copolymers of different composition as physical coatings: a comparative study.

In this work, a comparative study on the use of different polymers as physically adsorbed coatings for CE is presented. It is demonstrated that the use of ad hoc synthesized polymers as coatings allows tailoring the EOF in CE increasing the flexibility of this analytical technique. Namely, different polymers were synthesized at our laboratory using different percentages of ethylpyrrolidine methacrylate (EpyM) and N,N-dimethylacrylamide (DMA). Thus, by modifying the percentage of EpyM and DMA monomers it is possible to manipulate the positive charge of the copolymer, varying the global electrical charge on the capillary wall and with that the EOF. These coated capillaries are obtained by simply flushing a given EpyM-DMA aqueous solution into bare silica capillaries. It is shown that by using these coated capillaries at adequate pHs, faster or more resolved CE separations can be achieved depending on the requirements of each analysis. Moreover, it is demonstrated that these coated capillaries reduce the electrostatic adsorption of basic proteins onto the capillary wall. Furthermore, EpyM-DMA coatings allow the reproducible chiral separation of enantiomers through the partial filling technique (PFT). The EpyM-DMA coated capillaries are demonstrated to provide reproducible EOF values independently of the pH and polymer composition with%RSD values lower than 2% for the same day. It is also demonstrated that the coating procedure is reproducible between capillaries. The compatibility of this coating protocol with CE in microchips is discussed.

Acrylamides↗

PubMed2006

Antithrombogenic properties of bioconjugate streptokinase-polyglycerol dendrimers.

Dendrimers are monodisperse, spherical and hyperbranched synthetic macromolecules with a large number of surface groups that have the potential to act as carriers for drug immobilization by covalent binding or charge transfer complexation. In this work, a bioconjugate of streptokinase and a polyglycerol dendrimer (PGLD) generation 5 was used to obtain fibrinolytic surfaces. The PGLD dendrimer was synthesized by the ring opening polymerization of deprotonated glycidol using polyglycerol as core functionality in a step-growth processes denominated divergent synthesis. The PGLD dendritic structure was confirmed by gel permeation chromatography (GPC), nuclear magnetic resonance (1H-NMR, 13C-NMR) and matrix assisted laser desorption/ionization (MALDI-TOF) techniques. The synthesized dendrimer presented low dispersion in molecular weights (Mw/Mn = 1.05) and a degree of branching of 0.82 which characterize the polymer dendritic structure. The blood compatibility of the bioconjugate PGLD-Sk was evaluated by in vitro assays such as platelet adhesion and thrombus formation. Uncoated polystyrene -microtitre plates (ELISA) was used as reference. The epifluorescence microscopy results indicate that PGLD-Sk coating showed an improved antithrombogenic character relative to the uncoated ELISA plates.

Biocompatible Materials↗

PubMed2006

Physicochemical and antimicrobial properties of boron-complexed polyglycerol-chitosan dendrimers.

A polyglycerol with dendritic structure (PGLD) was synthesized by ring-opening polymerization of deprotonated glycidol using a polyglycerol as core functionality in a step-growth process. Then, PGLD reacted with O-carboxymethylated chitosan to obtain PGLD-chitosan dendrimer (PGLD-Ch). After the reaction of PGLD-Ch with boric acid, there was a marked increase in the bulk viscosity evidencing physically that boron can initiate a charge transfer complex formation, (PGLD-Ch)B. Gel permeation chromatography analysis was used to characterize the molecular weight and the polydispersivity of the synthesized PGLD-Ch. A dendritic structure with a molecular mass of 16.7 kDa and a narrow polydispersity (Mw/Mn = 1.05) was obtained. 1H-NMR and 13C-NMR measurements were employed to assess the degree of branching in PGLD. The obtained value of 0.85 indicates the tendency toward a dentritic structure for PGLD. The glass transition temperature values of (PGLD-Ch)B membranes containing 10% and 30% PGLD were -19 degrees C and -26 degrees C, respectively, which favor its potential use as surface coating of several polymers. The in vitro cytotoxicity was evaluated using the minimum essential medium elution test assay. Extracts of boron-complexed PGLD exhibited lower cytotoxicity than the controls, suggesting that the material has an improved biocompatibility. Antibacterial studies of (PGLD-Ch)B against Staphylococcus aureus and Pseudomonas aeruginosa showed a significant activity. Our study confirms and supports the effectiveness of (PGLD-Ch)B as an antimicrobial coating due to its capacity in suppressing the bacterial proliferation. The best in vivo response was found for (PGLD-Ch)B-30 membranes, which exhibited higher synthesis of collagen fibers than PGLD-ChB-10.

Animals↗

PubMed2005

Injectable and self-curing composites of acrylic/bioactive glass and drug systems. A histomorphometric analysis of the behaviour in rabbits.

Injectable self-curing systems based on PMMA, phosphate-free bioactive glasses and the drug fosfosal, a phosphate derivative of salicylic acid with analgesic and moderate anti-inflammatory properties, have been tested in vivo to evaluate their biocompatibility. The model consisted of the injection of dough of cement into a defect created in the femur of rabbits, and the cure of the cement in situ after implantation. The biological response was studied in the short and long terms by macroscopic, radiological and histopathological examination, and quantitatively by histomorphometric and statistical analysis considering the most representative variables at the bone-cement interface: cement, bone marrow, newly formed bone and connective tissue. All bioactive formulations presented resorption of the cement at the end of the experiment in contrast to the control of PMMA, due to the presence of resorbable components. The presence or absence of the phosphate group added by the drug fosfosal influenced mainly on the new bone formation process. The cement formulated with bioactive glasses and in absence of fosfosal produced the maximum amount of neoformed bone at 2 weeks, and then it resorbed at 4 weeks to give a higher amount of neoformed bone at the end of the experiment, compared with the formulation containing only fosfosal. The presence of fosfosal and bioactive glass together affected the ossification process strongly. The osseous tissue was produced more gradually but it continuously increased giving rise to a more stable bone at the end of the experiment.

Animals↗

PubMed2005

Self-curing controlled release systems for steroids. Application of prednisolone-based polymeric systems to ear diseases.

An injectable delivery system for prednisolone has been prepared based on a self-curing formulation comprised of poly(methyl methacrylate) particles and hydroxyethyl methacrylate as monomer. The polymerisation reaction was initiated by the redox system 4,4'-bis (dimethylaminobenzydrol)/benzoyl peroxide (BZN/BPO) and followed at 25 degrees C by measuring the time-temperature profile. A maximum temperature of 53 degrees C and a setting time of 15 min were obtained, calculated according to standard specifications. The swelling of the cured system was studied in phosphate-buffered saline (PBS) at 37 degrees C giving a hydration degree at equilibrium of 20%. The swelling kinetics fitted a fickian behaviour at the initial stages of the experiments, with a diffusion coefficient of 0.72 x 10(-7) cm2/s. The release of the drug was sustained from the beginning without an initial drug burst. The study of the wettability showed a rather hydrophilic character of the surface of the loaded system, and the biocompatibility evaluated through MTT assay revealed the absence of cytotoxicity due to the release of toxic substances.

Animals↗

PubMed2005

Acrylic bone cements modified with beta-TCP particles encapsulated with poly(ethylene glycol).

Beta-tricalcium phosphate (beta-TCP) has been encapsulated with poly(ethylene glycol) (PEG) to improve the filler/cement interface, and it was later incorporated to a poly(methyl methacrylate) bone cement in order to obtain cements with improved stability in the long term. Size and size distribution of the agglomerates forming the initial powder was drastically changed after its dispersion in a PEG aqueous solution. Whereas the initial beta-TCP particles had a 584 microm average diameter, the treated particles (TCP-PEG) presented more than 60% of the particles in a range of 2-6 microm. The effect of adding the treated particles to an acrylic cement was evaluated in terms of curing parameters, in vitro behaviour and mechanical performance. The presence of the TCP-PEG particles did not affect either peak temperature or setting time, indicating a good homogeneity of polymerising mass in contrast to the effect observed with the plain beta-TCP particles, which gave rise to higher setting times. In vitro behaviour studies revealed hydration degree values of the modified cements comparable to that of PMMA cements. Early stages of water uptake was Fickian in nature for all the experimental formulations indicating that the water absorption followed a diffusion controlled mechanism. After 3 months of storage in SBF the experimental formulations presented values of compressive strength in the range 76-78 MPa, higher than the minimum required by ISO 5833 (70 MPa) and those of tensile strength in the range 42-48 MPa, higher than the minimum reported for commercial formulations (30 MPa), but no significant differences in the strengths and elastic modulus were observed with the treatment of the filler particles. This observation was confirmed by ESEM analysis of the tensile fracture surfaces, which revealed a rather good cohesion between the bioceramic particles with some gaps around them, independently of the type of particles. The themogravimetric analysis of dry and wet specimens showed a higher dissolution rate of the plain beta-TCP particles in comparison to the encapsulated ones, indicating that the PEG adsorbed on the surface of the TCP particles could be a way to control the resorbability of the bioceramic component.

Absorption↗

PubMed2004

Evaluation of drug delivery characteristics of microspheres of PMMA-PCL-cholesterol obtained by supercritical-CO2 impregnation and by dissolution-evaporation techniques.

Poly(methyl methacrylate), PMMA, and of PMMA/Poly(epsilon-caprolactone), PCL, microspheres were loaded with different amounts of cholesterol by using a supercritical carbon dioxide (SC-CO2) impregnation process in order to use a clean technique with the absence of organic solvents, and to provide information for the infusion of additives into nonporous polymeric substrates. A conventional dissolution-evaporation method was also used to obtain PMMA and PMMA-PCL microparticles loaded with cholesterol. The obtained microspheres were characterized by environmental scanning electronic microscope, ESEM, nuclear magnetic resonance spectroscopy, NMR, and differential scanning calorimetry, DSC, thermal analysis. A comparison of drug release from particles obtained using both methods, the supercritical and the conventional, is presented.

Calorimetry, Differential Scanning↗

PubMed2004

Modulation of proteins adsorption onto the surface of chitosan complexed with anionic copolymers. Real time analysis by surface plasmon resonance.

The interpolyelectrolyte complex formation between chitosan and anionic polyacrylic derivatives, bearing sulfonic moieties, as well as the protein adsorption onto the chitosan/polyacrylic complexes were studied by surface plasmon resonance (SPR) optical biosensor. This unique technique allows a real time monitoring of different surface molecular interactions with very high sensitivity. The acrylic macromolecules are two families of copolymers of 2-acrylamido-2-methylpropane sulfonic acid (AMPS) and, respectively, 2-hydroxyethylmethacrylate (HEMA) and N,N'-dimethylacrylamide (DMAA). The complexation process was evaluated through the SPR measurements resulting from the flowing of polyacrylic aqueous solution over the sensor previously coated with chitosan. The SPR was able to differentiate strong ionic bonds from other weak and reversible interactions. By means of the coated sensors (uncomplexed and the whole series of complexed chitosan), SPR cold be used for a simple "in vitro" protein adsorption analysis, by flowing aqueous solutions of albumin and fibrinogen. While both proteins were adsorbed on the uncomplexed chitosan, the complexed coatings exhibited different and very promising behaviors. In particular, they showed no adsorption or only selective adsorption of albumin.

Adsorption↗

PubMed2004

Hydrophilic polymer drug from a derivative of salicylic acid: synthesis, controlled release studies and biological behavior.

Hydrophilic polymeric drugs bearing "Triflusal" (4-trifluoromethylsalicylic acid), a drug widely used as antithrombogenic agent (Disgren), have been prepared by free radical copolymerization of methacryloyloxyethyl [2-(acetyloxy)-4-(trifluoromethyl)] benzoate (HTRF) and N,N'-dimethylacrylamide (DMA). The reactivity ratios of both monomers have been determined by 1H NMR spectra by applying non-linear least square treatments to the copolymerization equation (terminal model), and the kinetic parameters obtained indicated that the microstructure of copolymer chains is homogeneous, with a random distribution of the active HTRF units along the copolymer chains. That means that for the copolymer system THDMA22 used in this work, HTRF units are mainly isolated in relatively long DMA sequences. Therefore, in this structure the intramolecular interactions between adjacent HTRF units are negligible. Release of Triflusal from THDMA22 has been studied in vitro using buffered solutions at pH = 2, 7.4 and 10 and 37 degrees C. The system showed an interesting pseudo-zero order release profile at pH = 7.4 during several months. It has been also evaluated the pharmacological activity and the behavior of the system in contact with biological media. In this sense, we have carried out some in vitro studies about the antiaggregant properties and biocompatibility of THDMA22. Results demonstrate that this copolymer inhibits platelet aggregation in its macromolecular form and presents a good biocompatibility with Human Osteoblastic Cells (HOS).

Humans↗

PubMed2004

Macroporous poly(epsilon-caprolactone) with antimicrobial activity obtained by iodine polymerization.

The most serious problem usually encountered in the field of implanted biomedical devices is infectious morbidity as a primary source of mortality. In this work, the synthesis and characterization of a macroporous iodine-based sanitizer (iodophor), poly(caprolactone)-iodine (PCL-I(2)), are presented. Characterization methods include nuclear magnetic resonance spectroscopy, gel permeation chromatography, nitrogen adsorption-desorption, and scanning electron microscopy. The in vitro cytotoxicity to CHO cells based on cell viability with Chinese hamster ovary cells (CHO) and antimicrobial activities against Escherichia coli and Staphylococcus aureus were examined. The obtained macropore PCL-I(2) structures had a rather narrow size distribution. The PCL-I(2) iodophor was noncytotoxic to Chinese hamster ovary cells. The antimicrobial activities of the PCL-I(2) were assessed against E. coli and S. aureus. The tested PCL-I(2) showed better antimicrobial activity against E. coli than against S. aureus.

Animals↗

PubMed2004

Polymeric drugs with prolonged sustained delivery of specific anti-aggregant agents for platelets: kinetic analysis of the release mechanism.

The in vitro aqueous behaviour of a metacryloyloxyethyl [2-(acetyloxy)-4-(trifluoromethyl)]benzoate (THEMA)/N,N'-dimethylacrylamide (DMA) copolymer with a THEMA molar content of 39% (labeled THDMA39) has been investigated. This composition has been selected to achieve a system able to keep both the non-water solubility during the release and the resorbability (and the water solubility) after the completion of the drug release. This copolymer exhibited, at pH 7.4, a constant release during several months, very interesting for a long term treatments required for the application of some cardiovascular devices. A kinetic model has been developed to explain the pseudo-zero-order kinetics of the release process. This model, which considers (from the aqueous studies) a linear increase with time of the amount of water present in the polymeric matrix, has been able to fit adequately the experimental data.

Acrylamides↗

PubMed2003

New physically adsorbed polymer coating for reproducible separations of basic and acidic proteins by capillary electrophoresis.

In this work, a new physically adsorbed coating for capillary electrophoresis (CE) is presented. The coating is based on a N,N-dimethylacrylamide-ethylpyrrolidine methacrylate (DMA-EPyM) copolymer synthesized in our laboratory. The capillary coating is simple and easy to obtain as only requires flushing the capillary with a polymer aqueous solution for 2 min. It is shown that by using these coated capillaries the electrostatic adsorption of a group of basic proteins onto the capillary wall is significantly reduced allowing their analysis by CE. Moreover, the DMA-EPyM coating provides reproducible separations of the basic proteins with RSD values for migration times lower than 0.75% for the same day (n = 5) and lower than 3.90% for three different days (n = 15). Interestingly, the electrical charge of the coated capillary wall can be modulated by varying the pH of the running buffer which makes possible the analysis of basic and acidic proteins in the same capillary. The usefulness of this coating is further demonstrated via the reproducible separation of whey (i.e. acidic) proteins from raw milk. The coating protocol should be compatible with both CE in microchips and CE-MS of different types of proteins.

Adsorption↗

PubMed2003

Central neural tumor destruction by controlled release of a synthetic glycoside dispersed in a biodegradable polymeric matrix.

An octyl N-acetylglucosaminide derivative with a pentaerythritol chain at position 6 has been synthesized and evaluated as an inhibitor of neural tumor growth. The glycoside inhibited the growth of a neuroectodermic tumor implanted in rats and, when loaded on a slow-delivery polymer disk, caused the destruction of cultured human astroblastoma obtained after surgical biopsy.

Acetylglucosamine↗

PubMed2003

Polymeric matrices based on graft copolymers of PCL onto acrylic backbones for releasing antitumoral drugs.

Graft copolymers of poly(epsilon-caprolactone) (PCL) on poly(dimethylacrylamide) (PDMAm), poly(methylmethacrylate) (PMMA), or on copolymers of poly(DMAm-co-MMA) have been synthesized and characterized by (1)H NMR spectroscopy, differential scanning calorimetry (DSC), and size exclusion chromatography (SEC). These partially biodegradable copolymer matrices have been proposed as drug delivery systems for the release of low-molecular-weight glycosides. Octyl-N-acetyl-6-O-[2,2-bis(hydroxymethyl)-3-hydroxypropyl]-alpha-D-glucosamide, a synthetic carbohydrate able to inhibit the proliferation of human malignant glioma cells in culture and transplanted glioma in rats was selected as drug model. The in vitro aqueous behavior of four drug-loaded and unloaded graft copolymers of different MMA: DMAm and PCL ratios has been analyzed performing swelling, degradation, and drug release experiments. An intimate dependence of the aqueous behavior with the composition has been found. The higher was the DMAm content, the higher was the hydrophilicity of the synthesized systems as well as the swelling, degradation, and drug release rate. In vivo experiments in pigs demonstrated the very good tolerance of drug-loaded implanted polymeric discs, and that >95% of the charged drug is released after 2 months' implantation.

Acrylamides↗