Biomedical subjects

Khee Hiang Lim

Publications and source records attributed to Khee Hiang Lim.

7 recordsLinked to original sources

PubMed2006

Forces at single point attached commissures (SPAC) in pericardial aortic valve prosthesis.

OBJECTIVE: New pericardial aortic bioprostheses (3F Therapeutics and temporarily stented autologous pericardial valve prosthesis) were developed recently. These valves are designed with commissures connected to the aortic wall at only three single points (single point attached commissures (SPAC)). The aim of this study was to investigate the forces acting on SPAC during varying pressure load. METHODS: Aortic roots with diameters 19, 25, and 29 mm were made using silicone polymer. A bovine pericardial SPAC aortic valve prosthesis was constructed using a 3D-mold and was implanted in the silicone aortic root. The base of the valve was sutured onto the aortic annulus with 4-0 polypropylene running suture and each commissure was sutured to a miniaturized force transducer with only one 3-0 polypropylene U-stitch. Three silicon aortic roots of each size were pressurized up to 200 mmHg and forces on SPAC were measured. RESULTS: All valves remained competent at a pressure of 200 mmHg. Recordings showed a linear correlation between applied pressure and forces measured at SPAC. At a pressure of 80 mmHg (equivalent to diastolic pressure), the forces were 0.44+/-0.22N, 1.15+/-0.18N, and 2.00+/-0.35N in annular diameters 19 mm, 25 mm, and 29 mm, respectively. It was observed, that the main forces were acting along the axial direction and not along the radial direction. CONCLUSIONS: Forces on "single point attached commissures" in pericardial aortic valves were measured. These forces were acting mainly in axial direction and not in radial direction. This knowledge is important for the implantation technique of SPAC pericardial aortic valves.

Animals↗

PubMed2005

Three-dimensional asymmetrical modeling of the mitral valve: a finite element study with dynamic boundaries.

BACKGROUND AND AIM OF THE STUDY: Previous computational studies of the normal mitral valve have been limited because they assumed symmetrical modeling and artificial boundary conditions. The study aim was to model the mitral valve complex asymmetrically with three-dimensional (3-D) dynamic boundaries obtained from in-vivo experimental data. METHODS: Distance tracings between ultrasound crystals placed in the sheep mitral valve were converted into 3-D coordinates to reconstruct an initial asymmetric mitral model and subsequent dynamic boundary conditions. The non-linear, real-time left ventricular and aortic pressure loads were acquired synchronously. A quasi-static solution was applied over one cardiac cycle. RESULTS: The mitral valve leaflet stress was heterogeneous. The trigones experienced highest stresses, while the mid-anterior annulus between trigones experienced low stress. High leaflet stress was observed during peak pressure loading. During isovolumic relaxation, the leaflets were highly stretched between the anterolateral trigone and the posteromedial commissure, resulting in a prominent secondary leaflet stress re-increment. This has not been observed previously, as symmetric models with artificial boundary conditions were studied only in the ejection phase. CONCLUSION: Here, the first asymmetrical mitral valve model synchronized with 3-D dynamic boundaries and non-linear pressure loadings over the whole cardiac cycle based on in vivo experimental data is described. Despite its limitations, this model provides new insights into the distribution of leaflet stress in the mitral valve.

Animals↗

PubMed2005

Aortic root dynamics are asymmetric.

BACKGROUND AND AIM OF THE STUDY: The presence of conformational changes in the aortic root during the cardiac cycle is well known, but precise information on time-related changes at each level of the root is lacking. METHODS: High-resolution, 3D sonomicrometry (200 Hz) was applied in an acute sheep model. Twelve crystals were implanted in eight sheep at each base (n = 3), commissure (n = 3), sinotubular junction (n = 3) and ascending aorta (n = 3). Under stable hemodynamic conditions, geometric changes of the perimeter of each sinus of Valsalva, sinus height, and twist and root tilt angles were time-related to left ventricluar (LV) and aortic pressures. RESULTS: Expansion of the perimeter of the three sinuses of Valsalva was homogeneous, but in significantly different proportions (p < 0.001): the right sinus expanded (+32.4 +/- 2.4%) more than the left (+29.3 +/- 3.2%), and more than the non-coronary (NC) sinus (+25.8 +/- 1.7%). A similar pattern was found for aortic root height: right greater than left, and left greater than NC sinus (p < 0.001). This asymmetry resulted in changes of the root's twist and tilt angles. Although the twist deformation was consistent for each sheep, no general pattern was found. The aortic root tilt angle (between the basal plane and the commissural plane) was 16.3 +/- 1.5 degrees at end-diastole (angle oriented posteriorly and to the left). During systole, it was reduced by 6.6 +/- 0.5 degrees, aligning the LV outflow tract with the ascending aorta. This tilt angle returned to its original value after valve closure. CONCLUSION: Aortic root expansion is asymmetric, generating precise changes in its tilt angle. During systole, tilt angle reduction resulted in a straight cylinder that probably facilitates ejection; during diastole, the tilt angle increased, probably reducing leaflet stress. These findings should impact upon surgical procedures and the design of new prostheses.

Animals↗

PubMed2004

Sonometric study of the normal tricuspid valve annulus in sheep.

BACKGROUND AND AIM OF THE STUDY: Mitral valve dynamic changes during the cardiac cycle have been previously studied in sheep using sonomicrometry. The study aim was to analyze geometric changes of the normal tricuspid annulus in sheep using a similar methodology. This is most likely the first tricuspid valve study using high temporal resolution (200 Hz = 200 data points per second). METHODS: Thirteen crystals were implanted in seven sheep along the annulus (n = 6), at the tips of papillary muscles (n = 3), at the free edge of the leaflets (n = 3), and at the apex of the left ventricle (n = 1). Recordings (10 s) of crystal distances were used to create a three-dimensional (3D) coordinate system based on the least-squares plane of the annulus, and maximum and minimum values were calculated for length, area, and position in xyz coordinates. RESULTS: During the cardiac cycle, the tricuspid annulus area expanded 28.6 +/- 3.6% with similar maximum expansions of each segment along the annulus: septal (10.4 +/- 1.2%), anterior (13.0 +/- 1.5%), and posterior (14.0 +/- 1.6%). The annulus was saddle-shaped, with a circumferential expansion from elliptical at minimum area to more circular at maximum area. The time delay to maximum leaflet area and maximum papillary area occurred 83 +/- 13 ms and 279 +/- 30 ms respectively after maximum annulus area. CONCLUSION: The tricuspid valve undergoes continual and complex geometric changes during the cardiac cycle. In addition, the annulus expands significantly due to similar increases in length of the septal and free wall segments. The annulus is not in a single plane, but is saddle-shaped. The expansion and contraction of the tricuspid valve complex is stepwise, and sequential from base to apex.

Animals↗

PubMed2004

Flat or curved pericardial aortic valve cusps: a finite element study.

BACKGROUND AND AIM OF THE STUDY: The finite element method (FEM) has frequently been used to investigate the behavior of the aortic valve, but studies on the performance and behavior of free-hand autologous pericardial aortic valves reconstructed using specially designed valve molds have not been performed. The study aim was to demonstrate the effectiveness of a three-dimensional (3-D) cusp of the authors' design (H-Mold) versus a two-dimensional (2-D) (flat) cusp using a FEM to compare stress distribution and leaflet contact properties. METHODS: Solid models of the aortic root and valve cusps were constructed using a computer-aided design package. All models had different free edge lengths and surface areas, but a constant leaflet attachment length corresponding to a 19 mm annulus diameter. A static pressure of 80 mmHg was applied to all models. RESULTS: The maximum von Mises stress value in the H-Mold at the cusp commissure was 34.5% lower than the stress value in the flat leaflet, while the contact area in the H-Mold leaflet was 85.7% greater than that of the flat leaflet. The length of leaflet free edge greatly influenced maximum von Mises stress intensity at the commissures, and the contact area between leaflets was mainly affected by the geometric shape of the leaflet and its surface area. CONCLUSION: 3-D leaflet geometry was found positively to influence leaflet stress distribution and coaptation. This geometry should have a significant impact on the reliability and long-term durability of pericardial aortic valve reconstruction.

Aortic Valve↗

PubMed2003

Comparison of human and porcine aortic valves.

We compared the anatomy of human and porcine aortic valves. Porcine hearts were collected from the abattoir. Human hearts from patients who had died of non-cardiac causes were examined in the mortuary; only undamaged and anatomically normal hearts were used. Silicon casts were prepared by injecting engineering silicon at 80 mm Hg into the aortic arch. Various features of the aortic valve were measured: circumference, length between the commissural end point and central point of coaptation, surface diameter, and surface area. In total, 12 porcine and 12 human aortic valves were studied. The average circumferences of the human and porcine aortic valves were 8.00 +/- 0.2 (SD) cm and 7.90 +/- 1.0 cm, respectively. The central point of coaptation in human valves was skewed toward the left coronary cusp, whereas in porcine valves it was skewed toward the non-coronary cusp. In human aortic valves, the non-coronary cusp had the largest surface diameter and surface area with mean measurements of 3.6 +/- 0.2 cm and 1.230 +/- 0.228 cm(2), respectively; the left coronary cusp was smallest for the same variables with measurements of 3.1 +/- 0.3 cm and 0.898 +/- 0.357 cm(2). In porcine valves, the right coronary cusp had the largest surface diameter and surface area with mean measurements of 3.9 +/- 0.7 cm and 1.716 +/- 0.81 cm(2), respectively; the non-coronary cusp was the smallest for the same variables with measurements of 2.9 +/- 0.5 cm and 1.023 +/- 0.659 cm(2). These differences suggest that when using porcine valves as transplant material (e.g., stentless valves), geometric considerations, such as commissural length, may be important.

Anatomy, Comparative↗

PubMed2002

Dynamic balance of the aortomitral junction.

OBJECTIVE: The aortic and mitral valves have been studied in isolation, as if their functions were independent. We hypothesized that both valves work in synchrony on the basis of the shared myocardial pump and orifice. METHODS: Six sonometric crystals (7 sheep) were placed in both trigones, the midpoint of the anterior and posterior anulus, and the lateral extremities of the posterior anulus. In a separate series of animals, 3 crystals (8 sheep) were implanted in the aortic annular base of the right, left, and noncoronary sinuses of Valsalva. In an acute, open-chest model, under stable hemodynamic conditions, geometric changes were time related to simultaneous left ventricular and aortic pressures. RESULTS: From mid-diastole to end-systole, the mitral anulus area contracted by -16.1% +/- 1.9% (mean +/- SEM), whereas the aortic base area expanded by +29.8% +/- 3.3% during systole. The mitral anulus deformation was heterogeneous. In systole, the anterior mitral anulus expanded (intertrigonal distance, +11.5% +/- 2.3%) and the posterior mitral anulus contracted (distance between lateral extremities of the posterior anulus, -12.1% +/- 1.5%). The intertrigonal distance corresponded to the base of the left and noncoronary sinus of Valsalva, which expanded similarly during systole (+12.9% +/- 2.0%). The anteroposterior diameter of the mitral anulus was reduced twice that of the transverse diameter. This disparity of reduction can be explained by the posterior displacement of the intertrigonal area corresponding to the systolic aortic root expansion. CONCLUSIONS: Mitral anulus deformation is closely related to aortic root dynamics. During systole, the posterior movement of the aortic curtain allows for aortic root expansion, probably to maximize ejection, whereas during diastole, aortic root reduction participates in mitral anulus dilatation. These findings should affect mitral and aortic surgical approaches.

Animals↗